2017 INFINITI QX30 oil capacities

6.Avoid Idling
•Shutting off your engine when safe for
stops exceeding 30 seconds saves fuel
and reduces emissions.
7. Buy an Automated Pass for Toll Roads
•Automated passes permit drivers to use
special lanes to maintain cruising speed
through the toll and avoid stopping and
starting.
8. Winter Warm Up
•Limit idling time to minimize impact to
fuel economy.
•Vehicles typically need no more than 30
seconds of idling at start-up to effectively
circulate the engine oil before driving.
•Your vehicle will reach its ideal operating
temperature more quickly while driving
versus idling.
9. Keeping your Vehicle Cool
•Park your vehicle in a covered parking
area or in the shade whenever possible.
•When entering a hot vehicle, opening the
windows will help to reduce the inside
temperature faster, resulting in reduced
demand on your A/C system.
•Keep your engine tuned up.
•Follow the recommended scheduled mainte-
nance.
•Keep the tires inflated to the correct pres-
sure. Low tire pressure increases tire wear
and lowers fuel economy.
•Keep all the wheels in correct alignment.
Improper alignment increases tire wear and
lowers fuel economy.
•Use the recommended viscosity engine oil.
For additional information, see Recom-
mended fluids/lubricants and capacities in
the 10. Technical information section
WARNING
•Do not drive beyond the performance capa-
bility of the tires, even with 4WD engaged.
Accelerating quickly, sharp steering ma-
neuvers or sudden braking may cause loss
of control.
•Always use tires of the same type, size,
brand, construction (bias, bias-belted or ra-
dial), and tread pattern on all four wheels.
•This vehicle is not designed for off-road
(rough road) use. Do not drive on sandy or
muddy roads that tires may get stuck in.
•For 4WD equipped vehicles, do not attempt
to raise two wheels off the ground and shift
the transmission to any drive or reverse po-
sition with the engine running. Doing so
may result in drivetrain damage or unex-
pected vehicle movement which could re-
sult in serious vehicle damage or personal
injury.
•Do not attempt to test a 4WD equipped ve-
hicle on a 2-wheel dynamometer (such as
the dynamometers used by some states for
emissions testing) or similar equipment
even if the other two wheels are raised off
the ground. Make sure that you inform the
test facility personnel that your vehicle is
INCREASING FUEL ECONOMY FOUR-WHEEL DRIVE (4WD) (IF EQUIPPED)
Starting and driving5-83

1. Park the vehicle on a level surface and applythe parking brake.
2. Start the engine and let it idle until it reaches the normal operating temperature,
then turn it off.
3. Remove the oil filler cap by turning it coun- terclockwise.
4. Remove the engine undershield.
5. Place a large drain pan under the drain plug.
6. Remove the drain plug with a wrench by turning it counterclockwise and completely
drain the oil. If the oil filter is to be changed,
remove and replace it at this time. For
additional information, refer to Changing
engine oil filter later in this section.
•Waste oil must be disposed of properly.
•Check your local regulations.
7. Clean and reinstall the drain plug and a new washer. Securely tighten the drain plug with
a wrench. Do not use excessive force.Drain
plug tightening torque: 22 ft-lb, 30 N•m
8. Refill engine with recommended oil through the oil filler opening, then install the oil filler
cap securely.
For additional information on drain and refill
capacity, refer to Recommended fluids/
lubricants and capacities in the
9. Maintenance and Schedules section.
The drain and refill capacity depends on the
oil temperature and drain time. Use these
specifications for reference only. Always use
the dipstick to determine when the proper
amount of oil is in the engine.
9. Start the engine. Check for leakage around the drain plug and oil filter. Correct as
required.
10. Turn the engine off and wait more than 10 minutes. Check the oil level with the dip-
stick. Add engine oil if necessary.
CHANGING ENGINE OIL FILTER
1. Park the vehicle on a level surface and applythe parking brake.
2. Turn the engine off.
3. Place a large drain pan under the oil filter
1.
4. Loosen the oil filter
1with an oil filter
wrench by turning it counterclockwise. Then
remove the oil filter by turning it by hand.
CAUTION
Be careful not to burn yourself. The engine oil
may be hot.
NDI1622NDI16102.0L gasoline engine
8-6Do-it-yourself

For recommended fuel, lubricants, fluids,
grease, and refrigerant, refer toRecommended
fluids/lubricants and capacities in the
10. Technical information section.
EMISSION CONTROL SYSTEM
MAINTENANCE
Drive belts*:
Check engine drive belts for wear, fraying or
cracking and for proper tension. Replace any
damaged drive belts
Engine air filter*:
Replace at specified intervals. When driving for
prolonged periods in dusty conditions, check/
replace the filter more frequently.
Engine coolant*:
Replace coolant at the specified interval. When
adding or replacing coolant, be sure to use only
Genuine INFINITI Engine Coolant or equivalent
in its quality (BASF Glysantin® G40®). (For
additional information, refer to Engine cooling
system in the9. Maintenance and Schedules
section.) NOTE
Mixing any other type of coolant or the use of
non-distilled water may reduce the recom-
mended service interval of the coolant.
Engine oil and oil filter:
Replace engine oil and oil filter at the specified
intervals. For recommended oil grade and vis-
cosity refer to
Recommended fluids/lubricants
and capacities in the10. Technical informa-
tion section.
Fuel filter:
Replace the fuel filter and drain the water at the
specified intervals.
Fuel lines*:
Check the fuel hoses, piping and connections
for leaks, looseness, or deterioration. Tighten
connections or replace parts as necessary.
Spark plugs:
Replace at specified intervals. Install new plugs
of the type as originally equipped.
CHASSIS AND BODY MAINTENANCE
Brake lines and cables:
Visually inspect for proper installation. Check
for chafing, cracks, deterioration, and signs of
leaking. Replace any deteriorated or damaged
parts immediately.
Brake pads, rotors, drums, & linings:
Check for wear, deterioration and fluid leaks.
Replace any deteriorated or damaged parts
immediately.
Exhaust system:
Visually inspect the exhaust pipes, muffler and
hangers for leaks, cracks, deterioration, and
damage. Tighten connections or replace parts
as necessary.
In-cabin microfilter:
Replace at specified intervals. When driving for
prolonged periods in dusty conditions, replace
the filter more frequently.
Propeller shaft(s):
Check for damage, looseness, and grease leak-
age. (4WD/AWD).
9-6Maintenance and Schedules

10 Technical information
Recommended fluids/lubricants and capacities . . . .10-2Fuel recommendation ..................10-3
Engine oil and oil filter recommendations ......10-5
Air conditioner system refrigerant and oil
recommendations ................... .10-6
Engine specifications ................... .10-7
Wheels and Tires ..................... .10-8
Dimensions ..........................10-8
When traveling or registering in another country . . .10-9
Vehicle identification ................... .10-9
Vehicle identification number (VIN) plate ......10-9
Vehicle identification number (chassis number) .10-10
Engine serial number .................10-10
F.M.V.S.S./C.M.V.S.S. Certification label ......10-10
Emission control information label ..........10-11
Tire and loading information label ..........10-11
Air conditioner specification label ..........10-11Installing front license plate
...............10-12
Vehicle loading information ................10-13
TERMS ..........................10-13
Vehicle load capacity .................10-14
Loading tips ...................... .10-15
Measurement of weights ...............10-15
Trailer towing ....................... .10-15
Uniform tire quality grading ...............10-16
Treadwear ....................... .10-16
Traction AA, A, B and C ................10-16
Temperature A, B and C ................10-16
Emission control system warranty ............10-17
Reporting safety defects ..................10-17
Readiness for inspection/maintenance (I/M) test . . .10-18
Event data recorders (EDR) (if so equipped) ......10-19
Owner’s manual/service manual order information . .10-19

The following are approximate capacities. The actual refill quantities may be slightly different. When refilling, follow the procedures instructedinthe
“8. Maintenance and do-it-yourself” section to determine the proper refill capacity.
Fluid types Capacity (Approximate) Recommended Fluids and Lubricants
US measure Imp Measure Liter
Fuel tank 13.2 gal
(4WD: 14.8 gal 11 gal
(4WD: 12.3 gal) 50 L
(4WD: 56 L)
–See Fuel recommendation later in this section.
Engine oil (*) The approximate capacities listed are for refilling during an engine oil change. *: For
additional information, seeChanging engine oilin the 8. Do-it-yourself section.
2.0L gasoline engine:
–Genuine INFINITI engine oil, Viscosity SAE 0W-30
For additional information, see Engine oil and oil filter recommendations later in this
section.
Drain and refill
With oil filter change 6 qt5 qt5.6 L
Cooling system with Reservoir 8.1 qt
6.7 qt 7.6
–Genuine INFINITI Engine Coolant or equivalent in its quality
BASF Glysantin® G40®
–Use Genuine INFINITI Engine Coolant, or equivalent in its quality, in order to avoid
possible aluminum corrosion within the engine cooling system caused by the use
of non-genuine engine coolant. Note that any repairs for incidents with the engine
cooling system while using non-genuine engine coolant may not be covered by the
warranty even if such incidents occurred during the warranty period.
Automatic Transmission Fluid
(ATF) 6.6 qt
5.5 qt6.21 L Shell DCT-M1
Brake fluid Refill to the proper fluid level according to the instructions
in the “8. Maintenance and do-it-yourself” section.
–Genuine INFINITI brake fluid or equivalent. DOT 4+–Never mix different types of fluids.
Differential gear oil 0.8 qt0.65 qt 0.74 L
–Castrol BOT 355 75W-85
Multi-purpose grease ———
–NLGI No. 2 (Lithium soap base)
Air conditioner system refriger-
ant ———
–HFC-134a
Air conditioner system lubri-
cant ———
–INFINITI A/C System Oil Type S or equivalent
RECOMMENDED FLUIDS/LUBRICANTS AND
CAPACITIES
10-2Technical information

level roads, it is recommended you have an
INFINITI retailer correct the condition. Failure to
correct the condition is misuse of the vehicle, for
which INFINITI is not responsible.
Incorrect ignition timing will result in knocking,
after-run and/or overheating. This in turn may
cause excessive fuel consumption or damage to
the engine. If any of the above symptoms are
encountered, have your vehicle checked. It is
recommended you visit an INFINITI retailer.
However, now and then you may notice light
spark knock for a short time while accelerating
or driving up hills. This is no cause for concern,
because you get the greatest fuel benefit when
there is light spark knock for a short time under
heavy engine load.
1API certification mark
2API service symbol
ENGINE OIL AND OIL FILTER
RECOMMENDATIONS
Selecting the correct oil
It is essential to choose the correct grade,
quality, and viscosity engine oil to ensure sat-
isfactory engine life and performance. For addi-
tional information, refer toRecommended
fluids/lubricants and capacities earlier in this
section. INFINITI recommends the use of an
energy conserving oil in order to improve fuel
economy.
Select only engine oils that meet the American
Petroleum Institute (API) certification or Interna-
tional Lubricant Standardization and Approval Committee (ILSAC) certification and SAE viscos-
ity standard. These oils have the API certifica-
tion mark on the front of the container. Oils
which do not have the specified quality label
should not be used as they could cause engine
damage.
Oil additives
INFINITI does not recommend the use of oil
additives. The use of an oil additive is not
necessary when the proper oil type is used and
maintenance intervals are followed.
Oil which may contain foreign matter or has
been previously used should not be used.
Oil viscosity
The engine oil viscosity or thickness changes
with temperature. Because of this, it is impor-
tant that the engine oil viscosity be selected
based on the temperatures at which the vehicle
will be operated before the next oil change.
Choosing an oil viscosity other than that recom-
mended could cause serious engine damage.
Selecting the correct oil filter
Your new vehicle is equipped with a high—
quality genuine INFINITI oil filter. When replac-
ing, it is recommended you use the genuine oil
filter or its equivalent for the reason described
in “Change intervals”.
NTI326
Technical information10-5

11 Index
ABS (Anti-lock Braking System).........2-9
Warninglight .................2-9
Active sound enhancement ..........5-67
Operation ...................5-67
Adaptive Front lighting System ........2-65
Aids .......................5-60 Forward emergency braking system ....5-60
Hill Start Assist (HSA) ............5-93
Intelligent Parking Assist (IPA) .......5-68
Air bags .....................1-47
Front passenger air bag switch .......1-47
Overview ....................0-2
Repair and replacement ...........1-56
Supplemental Restraint System ......1-38
Warninglight..............1-55, 2-12
Air cleaner filter .................8-13
Air conditioner .................4-42
Heater and air conditioner .........4-42
Refrigerant and lubricant ..........10-6
Servicing ...................4-51
Specification label .............10-11
Airfresheners...................7-4
Anti-theft alarm system ............2-58
AppGarage...................4-98 Screen ....................4-98
Settings screen ...............4-99
Around View Monitor ..............4-24
Moving object detection (MOD) ......4-37Settings
....................4-33
Audible reminders ................2-14
Audio .......................4-52
Operation precautions ...........4-52
Settings ...................4-80
Sourcebar..................4-65
System ....................4-52
Automatic transmission .............8-7
Fluid(ATF)...................8-7
Operation ...................5-18
Battery ......................8-9
Cautionlabel .................8-9
Coldweather.................5-93
Jump-starting .................6-10
Replacement - Intelligent Key .......8-20
Saver system ................2-86
Vehicle battery ................8-10
Blind Spot Warning (BSW) system ......5-35
Bluetooth®...................4-83 Hands-Free Phone System .....4-83,4-131
Information..................4-96
Streamingaudio..............4 -130
Booster seats ..................1-35
Precautions................. .1-35
B r

akes......................8-17 ABS (Anti-Lock Braking System) ......5-88
Adjustment..................8-17 Fluid ......................8-7
Forward emergency braking system
....5-60
Parking brake ................5-25
Precautions ..................5-87
System ....................5-87
Warninglight .................2-9
Break-inschedule................5-81
Brightness....................2-69 Instrumentpanel ..............2-69
Capacities and recommendations .......10-2
Coolant....................10-2
Fuel......................10-2
Oil.......................10-2
Refrigerant ..................10-2
Cardholder...................2-79
Center multi-function control panel ......4-2
Changing.....................8-4 Enginecoolant ................8-4
Engineoil ...................8-5
Engine oil filter ................8-6
Tires and wheels ..............8-32
Checking .....................8-4
Coolantlevel .................8-4
Engine oil level ................8-5
Child restraints .................1-20
Anchorage ..................1-23
ISOFIX installation ..............1-23

Precautions ..................1-20
Child safety ....................1-18
Rear door locks .................3-7
Cleaning ......................7-3
Alloy wheels ..................7-3
Chrome parts ..................7-3
Exterior .....................7-2
Glass ......................7-3
Interior .....................7-4
Leatherseatcovers ..............7-6
Removingspots ................7-3
Seatbelts....................7-5
Underbody ...................7-3
Washing.....................7-2
Waxing .....................7-2
Clock .......................2-76 Adjusting time ................2-76
Coat hooks ....................2-80
Cockpit.......................0-6 Overview ..................0-6,2-2
Cold weather ...................5-93
Battery .....................5-93
Driving on snow or ice ............5-94
Engine coolant ................5-93
Precautions..................5-93
Special equipment ..............5-94
Tire equipment ................5-94
Compact Disc (CD) ................4-70
Player .................4-70,4-126
Compartment ...................2-86 Connecting
....................4-88
Bluetooth® device ..............4-88
Bluetooth® Hands-Free Phone .......4-85
Coolant ......................10-2
Capacities ...................10-2
Changing engine coolant ...........8-4
Checking coolant level ............8-4
Coldweather .................5-93
Engine cooling system .............8-3
Temperature gauge ..............2-6
Corrosion protection ...............7-6
Environmental factors .............7-6
Cruisecontrol ..................5-44 Canceling ...................5-46
Operation ...................5-45
Cupholders....................2-79
Customer assistance ..............4-122
Defroster .....................2-61
Switch .....................2-61
D i

mensions....................10-8 Engine.....................10-7
Tires ......................10-8
Display ......................2-69 Brightness...................2-69
Vehicle information display .........2-15
Warningsandindicators...........2-29
Doors ........................3-7
Lift gate .....................3-7
Lockingkey...................3-5
Locks ......................3-4 Map pocket
..................2-82
Drive belts ....................8-12
Driving .......................5-18
Automatic Transmission ...........5-18
Cold weather .................5-93
Idle Stop/Start System ............5-27
Onsnoworice................5-94
Precautions ...................5-4
Emergency key ...................3-2
Engine.......................5-16 Before starting ................5-16
Changingenginecoolant...........8-4
Changingengineoil..............8-5
Changing oil filter ...............8-6
Checking coolant level ............8-4
Checking engine oil level ...........8-5
Cold weather .................5-93
Compartment ...............0-9,8-3
Cooling system .................8-3
Data ......................10-7
Oil........................8-5
Serial number ................10-10
Spark plugs ..................8-13
Starting ....................5-16
Event data recorders (EDR) ...........10-19
Exhaustgas ....................5-4 Precautions ...................5-4
Exterior .......................7-2
Cleaning.....................7-2
Lights .....................8-22
11-2Index