2017 Citroen GRAND C4 PICASSO Owner's Manual

151
C4-Picasso-II_en_Chap04_conduite_ed02-2016
Memorising speeds
Memorising
This function allows speeds to be saved, which can then be offered to set the two systems: the speed limiter (to limit the speed of the vehicle) or the
cruise control (for a vehicle cruising speed).
You can memorise up to six speed settings for each of the two systems. By default, some speed settings are already memorised.F

S
elect the system for which you want to
memorise new speed settings.
This function is accessible in the Driving
menu
of the touch screen.
F

Sel
ect the " Driving functions " tab, then
" Speed settings ".
F

P
ress the button corresponding to the
speed setting you want to modify.
As a safety measure, the driver must
carry out these operations when
stationary.
F

E
nter the new value using the numerical
keypad and confirm.
4
Driving

152
C4-Picasso-II_en_Chap04_conduite_ed02-2016
Speed limit recognition
This system allows the speed limit detected by
the camera to be displayed in the instrument
panel.
Specific speed limits, such as those for heavy
goods vehicles, are not displayed.
The display of the speed limit in the instrument
panel is updated as you pass a speed limit sign
intended for cars (light vehicles).The units for the speed limits (mph or
km/h) depend on the country you are
driving in.
It should be taken into account so that
you observe the speed limit.
For the system to operate correctly
when you change country, the units for
speed in the instrument panel must be
those for the country you are driving in. The automatic reading of road signs is a
driving assistance system and does not
always display speed limits correctly.
The speed limit signs present on the
road always take priority over the
display by the system.
The system cannot in any
circumstances replace the need for
vigilance on the part of the driver.
The driver must observe the driving
regulations and must adapt the speed
of the vehicle to suit the weather and
traffic.
It is possible for the system to not
display the speed limit if it does not
detect a speed limit sign within a preset
period.
The system is designed to detect signs
that conform to the Vienna Convention
on road signs.
To maintain correct operation of the
system: regularly clean the area in front
of the camera.Principles
Using a camera at the top of the windscreen,
this system detects and reads speed limit and
end of speed limit signs.
The system also takes account of information
on speed limits from the navigation system
mapping.
Driving

153
C4-Picasso-II_en_Chap04_conduite_ed02-2016
Display in the instrument panel
1. Indication of the speed limit. or
2.
I

ndication of the end of the speed limit.
Display of the speed
The system is active but is not detecting speed
limit information.
On detection of speed limit information, the
system displays the value. The driver can, if desired, adjust the
speed of the vehicle according to the
information given by the system.
The system is activated or deactivated in the
Driving menu of the touch screen.
Select the " Vehicle settings " tab, then
" Security " and "Recommended speed
display ".
Activation / Deactivation
It is necessary to update your
navigation mapping regularly in order to
receive accurate information on speed
limits from the system.
4
Driving

154
C4-Picasso-II_en_Chap04_conduite_ed02-2016
Memorising the speed setting
This memorisation is in addition to the display
of Speed limit recognition .
The driver can choose to adapt the speed
setting to the speed limit suggested, by
pressing the memorisation button at the speed
limiter controls, with the standard cruise
control, the dynamic cruise control or the
dynamic cruise control with Stop function.
This speed setting then replaces the previous
speed setting for the speed limiter and/or cruise
control. For more information on the Speed
limiter , Cruise control , Dynamic
cruise control or Dynamic cruise
control with Stop function , refer to
the corresponding sections. 1.
S

elect speed limiter/cruise control mode.
2.
M

emorise a speed setting.
Operating limits
The legislation on speed limits is specific to
each country.
The system does not take account of reduced
speed limits in the following cases:
-
p
oor weather (rain, snow),
-
a

tmospheric pollution,
-

t
railer, caravan,
-

d
riving with a space-saver type spare
wheel or snow chains fitted,
-

p
uncture repair using the temporary
repair
k

it,
-
y

oung drivers,
-
...
T

he system may be disrupted or not work at all
in the following situations:
-

p
oor visibility (inadequate street lighting,
falling snow, rain, fog),
-

w
indscreen area ahead of the camera dirty,
misty, frosty, covered with snow, damaged
or masked by a sticker,
-

f
ault with the camera,
-

o
bsolete or incorrect mapping,
-

h
idden road signs (other vehicles,
vegetation, snow),
-

s
peed limit signs that do not conform to the
standard, are damaged or distorted. 3.
S

peed limiter indication.
4.
M

emorise the speed.
5.
C

urrent speed setting.Steering mounted controls
Display in the instrument panel
Driving

155
C4-Picasso-II_en_Chap04_conduite_ed02-2016
F Make an initial press on this
button to request saving of the
speed suggested.
F

P
ress this button again to
confirm and save the new speed
setting.
Memorising the speed
F Switch on the speed limiter/cruise control.
Speed limiter/cruise control information is
displayed.
On detection of a speed limit sign, the system
displays the speed limit value and offers to
make it a new speed setting.
"MEM " flashes in the screen for a few seconds.
If the difference between the speed setting
and speed displayed by the recognition
system is less than 6 mph (10 km/h), the
MEM symbol is not displayed.
After a predetermined period, the screen
returns to the current display.
4
Driving

156
C4-Picasso-II_en_Chap04_conduite_ed02-2016
Steering mounted controls
6. Speed limiter on / pause indication.
7. Speed limiter mode selection indication.
8.
S

peed limiter setting.
Speed limiter - "LIMIT"
System which prevents the vehicle from exceeding the speed programmed by the driver.
The speed limiter cannot, in any circumstances,
replace the need to observe speed limits, nor can it
replace the need for vigilance on the part of the driver.
Once the programmed speed limit is reached,
additional pressure on the accelerator pedal
has no effect.
1.
S

elect speed limiter mode.
2.
L

ower programmed speed.
3.
R

aise programmed speed.
4.
S

peed limiter on / pause.
5.
D

isplay the list of memorised speeds or,
A

ccept the speed proposed by the speed
limit recognition.Displays in the instrument panel
S witching on the speed limiter requires
a programmed speed of at least 20 mph
(30
km/h).
The speed limiter is paused by operation of the
control.
The programmed speed can be exceeded
temporarily by pressing the accelerator firmly
beyond the point of resistance.
To return to the programmed speed, simply
release the accelerator pedal until the vehicle
returns to the programmed speed limit.
The programmed speed remains in the
memory when the ignition is switched off. For more information on Memorising speeds ,
refer to the corresponding section.
For more information on Speed limit
recognition and memorisation, refer to the
corresponding section.
Driving

157
C4-Picasso-II_en_Chap04_conduite_ed02-2016
Switching on / Pause
F Turn thumbwheel 1 to the "LIMIT" position:
the speed limiter mode is selected but is
not switched on (Pause).
F

S
witch the speed limiter back on by
pressing button 4 , if the speed displayed
is suitable (by default, the last speed
programmed).
F

Y
ou can temporarily stop the speed limiter
by pressing button 4 again: the display
confirms that it has been stopped (Pause). You do not have to switch the speed limiter on
in order to set the speed.
Once the function is selected, you can modify
the speed setting by:
-

u
sing buttons 2 and 3, raising or lowering
the speed displayed:
F

b
y successive short presses, to modify
by + or - 1 mph (km/h),
F

b
y a maintained press, to modify in steps
of + or - 5 mph (km/h).
Adjusting the speed limiter
setting
- pressing button 5 :
F t he six speeds memorised are displayed
in the touch screen,
F

p
ress the button corresponding to the
limit speed chosen.
The value is displayed in the instrument panel.
The selection screen closes after a few
moments.
-

b
y pressing button 5 , if your vehicle has
speed limit recognition:
F

t
he speed to memorise is displayed in
the instrument panel,
F
press button 5 again to save the speed.
The value is then displayed in the instrument
panel.
For more information on Speed limit
recognition and memorisation, refer to the
corresponding section.
4
Driving

158
C4-Picasso-II_en_Chap04_conduite_ed02-2016
On sharp acceleration, as when
descending a steep hill, the speed
limiter will not be able to prevent
the vehicle from exceeding the
programmed speed.
The limiter is temporarily deactivated
and the displayed programmed speed
flashes.
An audible signal accompanies the
flashing of the programmed speed
when exceeding the speed is not due to
an action by the driver.
The use of mats not approved by
CITROËN may inter fere with the
operation of the speed limiter.
To avoid any risk of jamming of the
pedals:
-
e
nsure that the mat is secured
c o r r e c t l y,
-

d
o not fit one mat on top of another.
Flashing of the dashes indicates a fault with the
speed limiter.
Have it checked by a CITROËN dealer or a
qualified workshop.
Operating fault
F Press
f irmly on the accelerator pedal,
going beyond the point of resistance ,
to
exceed the programmed speed limit.
The speed limiter is deactivated temporarily
and the displayed programmed speed flashes.
An audible signal accompanies the flashing
of the programmed speed when exceeding
the speed is not due to an action by the driver
(steep hill...).
As soon as the vehicle's speed returns to the
programmed value, the limiter operates again:
the display of the programmed speed becomes
steady again.
Switching off Temporarily exceeding the
programmed speed
F Turn the thumbwheel 1 to the "0" position. T
he display of speed limiter information
disappears.
Driving