Wheels
store the pressure again in the Infotainment
system
¢ page 352.
mm (T ir e Pr essure Monito ring System) Tire
pressure : malfunction ! See owner' s manual.
If
mm appears after switch ing the ignit ion on o r
while driving and the
[I] indicator light in the in
strument cluster blinks fo r approximately one
minute and then stays on, there is system mal
function. Try to store the correct tire pressures
¢ page 352 . In some cases, you must drive for
several minutes after storing the pressures until
the ind icator light turns off . If the i ndicator light
does t urn off o r tu rns on aga in afte r a short peri
od of time , d rive to an au tho riz ed A ud i dealer o r
author ized Audi Service Facility immed iate ly to
have the ma lfunction co rrected .
A WARNING
-If the t ire pressu re indicator appears in the
display, reduce your speed immediate ly and
avoid any hard steer ing or braking maneu
vers. Stop as soon as possib le and check the
t ires and their pressu re.
- The driver is responsib le for maintaining the
correct tire pressure. You must check the
t ire pressure regu larly.
- Under certain conditions (such as a sporty
dr iv ing style, winter cond itions o r unpaved
roads), the tire p ressure mon itoring system
indicator may be delayed.
@ Tips
- The t ire pressure monitoring system can al
so stop work ing when there is an ESC mal
funct ion.
- Using snow chains may result in a system
malfunction.
- The t ire pressure monitoring system in your
Audi was calibrated with "A udi Orig inal
Tires"
¢ page 340. Using these ti res is rec
ommended .
352
' Storing tire pressures
If the tire pressure changes or a tire is replaced,
it must be confirmed in the Infotainment sys
tem .
"Make sure before stor ing that the t ire pressures
of all four tires meet the specified values and
are adapted to the load
¢ page 343 .
"Switch the ignit io n on.
" Sele ct in the Infotainment system:
IMENU J but
ton
> V ehicle > Servi ce & checks > Tire pres
s u re monitor
> Store tire pre ssure > Ye s, store
now .
'
(D Tips
Do not store the tire pressures if snow chains
are installed .
Run-flat tires
Introduction
Applies to: vehicles with run-flat tires
A run-flat tire helps to maintain vehicle mobility
when there is a loss of pressure.
Run-flat tires have reinforced sidewalls that pro
tect the tire if there is a loss of pressure.
If the ti re pressure monitoring system indicates a
l oss of pressure in one or severa l ti res, you can
continue driving on run-flat tires fo r at least 20
miles (30 km). Drive to an authorized A udi dealer
or authorized Audi Serv ice Facility immediately to
have the problem corrected.
Continuing to d rive on run-flat tire s is no
longe r po ssible if
- there is visible damage to the tires, such as
cracks in the sidewalls .
- strong vibrat ions are felt wh ile driving, or the
tire beg ins to smoke due to a strong build-up of
heat .
- the t ire was heavily damaged, for example in an
accident There is a r isk that parts of the tire
tread will detach and damage important veh i
cle components .
- the Electron ic Stabilization Contro l (ESC) is not
working or is cont inuously running .
u co ...... N r-... N ...... 0
0
:E: '
working .
I f it is no longer possib le to continue dr iv ing de
spite having run-flat tires, see an authori zed Aud i
dea ler or autho rized Aud i Service Facility for as
sistance.
A WARNING
Run-flat tires may only be used on vehicles
that were equ ipped with them at the factory.
- The veh icle must have suspension designed
for run-f lat tires and a factory- installed tire
pressure monitoring system.
- Incorrect use of run-flat tires can lead to ve
hicle damage or accidents . Contact an a u
thorized Aud i dea ler or authorized Audi
Service Facility to learn if run-flat tires may be used on your veh icle and if so, which
ones.
- If run-flat tires are used, they must be in
stalled on all four wheels. Mixing tire types
is not permi tted.
- If you have to dr ive when the tire pressure is
too low or there is no t ire pressure, note the
following:
- Do not drive faster than 50 mph (80 km/
h) because this increases the risk of an ac
cident. Observe any laws spec ific to the
country where you are driv ing.
- Avoid full-throttle acceleration, heavy
braking, and fast cornering, because this
increases the risk of an accident.
- The vehicle may become more difficult to
control.
- See an authorized Aud i dealer or author
ized Audi Service Fac ility for assistance if
the t ire is too heavily damaged.
- Have the faulty tires replaced and the rims
checked for damage by an author ized Audi
dealer or author ized Audi Se rvice Facility.
- The driver is responsib le for the vehicle, for
correcting the t ire pressure and for rep lac
ing faulty parts . Therefore, always adjust
yo ur dr iv ing to the g iven s ituation .
Wheel s
(D Tips
-Audi Original run-flat tires can be ident ified
by the "AOE" labeling on the t ire s idewa ll.
- You can use the tire mobility kit
~ page 360 on r un-flat tires.
353
Care and cleaning
Care and cleaning
General information
Regular, proper care helps to maintain your vehi
cle's value.
It can also be a requirement when
submitting warranty claims for corrosion damage
and paint defects on the body.
The required cleaning and care products can be
obtained from an authorized Audi dealer or au
thorized Service Facility. Read and follow the in
structions for use on the packaging .
A WARNING
-Using cleaning and care products incorrectly
can be dangerous to your health .
- Always store cleaning and care products out
of reach of children to reduce the risk of poi
soning .
@ For the sake of the environment
- Preferably purchase environmentally-friend
ly cleaning products.
- Do not dispose of leftover cleaning and care
products with household trash.
Car washes
The longer that deposits such as insects, bird
droppings, tree sap or road salt remain on the ve hicle, the more the surface can be damaged. High
temperatures such as those caused by sunlight
increase the damaging effect .
Before washing, rinse off heavy deposits with
plenty of water.
Stubborn deposits such as bird droppings or tree
sap are best removed with plenty of water and a microfiber cloth.
Also, wash the underside of your vehicle once road salt stops being used for the season .
Pressure washers
When washing your veh icle w ith a pressure wash
er, always follow the operating instructions pro
vided with the pressure washer. This is especially
important in regard to the pressure and spraying
distance. Do not aim the spray directly at the
354
seals on the side windows, doors, lids or the sun
roof* or at tires, rubber hoses, insulating materi
al, sensors* or camera lenses* . Keep a distance of
at least 16 in (40 cm).
Do not remove snow and ice with a pressure
washer.
Never use cone nozzles or high pressure nozzles.
The water temperature must not be above 140 °F
(60 °().
Automatic car washes
Spray off the vehicle before washing.
Make sure that the windows and roof* are closed
and the windshield wipers are off . Follow instruc
tions from the car wash operator, especially if
there are accessories attached to your vehicle.
If possible, use car washes that do not have
brushes.
Washing by hand
Clean the vehicle starting from the top and work
ing down using a soft sponge or cleaning brush.
Use solvent-free cleaning products.
Washing vehicles with matte finish paint by
hand
To avoid damaging the paint when washing, first
remove dust and large particles from your vehi
cle. Insects, grease spots and fingerprints are
best removed with a special cleaner for matte
finish paint .
Apply the product using a microfiber cloth. To
avoid damaging the paint surface, do not use too
much pressure.
Rinse the vehicle thoroughly with water. Then
clean using a neutral shampoo and a soft micro
fiber cloth .
Rinse the vehicle thoroughly again and let it air
dry. Remove any water residue using a chamois .
A WARNING
-
- Only wash the vehicle when the ignition is
off and follow the instructions from the car
u co ...... N r-... N ...... 0
0
:E: '
Component Situation Solution
T ex til es
Deposits adhering to Vacuum cleaner
art ifici al leat her, the surface
A lcan tara Water-based deposits Absorbent
cloth and mild soap solutiona>
such as coffee, tea,
b lood, etc.
Oil -based deposits Apply a m ild soap solution
a), blot away the dissolved o il or
such as oil, make-up, dye, treat afterward with water, if necessary
etc.
Special deposits such Special stain
remover, blot with absorbent material, treat
as ink, nail polish, la- afterward with mild soap solution, if necessary
a)
tex paint, shoe pol-
ish, etc.
Natu ral le ath er Fresh stains Wool cloth with a mild soap solution a)
Water-based deposits Fresh stains: absorbent cloth
such as coffee, tea, dried stains: stain
remover suitable for leather
b lood , etc.
Oi [-based deposits Fresh stains: absorbent cloth and stain
remover suitable
such as oil, make-up, for leather
etc. dried stains: oil cleaning spray
Special deposits such Spot remove r suitab le for leather
as ink, nail polish, la-
tex paint, shoe pol-
ish, etc.
Care Regularly apply condit ion ing c ream that protects from
lig ht and penet rates into the material. Use specia lly-co l-
ored conditioning cream, if necessary .
Carbon part s Deposits clean the same way as plast ic parts
a) Mi ld soap solution: maximum two tablespoons of neutral soap in 1 q uart (1 liter) of water
.8, WARNING
The windshield may not be trea ted with wa
ter-repelling windshield coating agents. Un
favorable cond itions such as wetness, dark
ness, or low sun can result in increased glare.
Wiper blade chatter is also possible.
@ Note
- Headlight s/tail li ght s
-Never clean headlights or tail lights with a
dry cloth or sponge.
- Do not use any cleaning product that con
tains alcohol, because they could cause
cracks to form.
- Whe els
-
- Never use any pa int polish or other abra
sive materials .
- Damage to the protect ive layer on the
rims such as stone chips or scratches must
be repaired immediately .
-Sen sor s/cam era l enses
- Neve r use warm or hot water to remove
snow or ice from the camera lens . This
could cause the lens to crack .
- Neve r use ab rasive cleaning materials or
a lcohol to clean the camera lens. This
could cause scratches and cracks .
-Doo r window s
-Remove snow and ice on windows and ex-
terior mirrors w ith a plast ic scraper . To
357
Emergency assistance
Emergency assistance
General information
... Park the vehicle as far as possible from moving
traffic in the event of a breakdown. In the event
of a flat tire, park the vehicle on a level surface .
It you are on a steep hill, be especially careful.
.,. Set the parking brake .
.,. Switch the emergency flashers on .
... Have the passengers exit the vehicle . They
should move to a safe place, for example be
hind a guard rail.
_& WARNING
Follow the steps given above . This is for your
protection and the for the safety of other driv
ers.
Equipment
Vehicle tool kit/tire mobility kit/vehicle
jack
App lies to: veh icles with the vehicle tool kit, tire mobility kit
an d ve hicle jack
The vehicle tool kit, vehicle jack, tire mobility kit
and compressor are stored in the luggage com
partment under the cargo floor cover. Lift the
cargo f loor using the handle.
_& WARNING
Improper use of the vehicle jack can cause se
rious personal injuries.
- Never use the screw driver hex head to
t ighten whee l bolts, since the bolts cannot
attain the necessary tightening torque if you
use the hex head, potentially causing an ac
cident.
- The factory-supplied jack is intended only
for your vehicle model. Under no circum
stances should it be used to lift heavy
vehicles or other loads; you risk injuring
yourself.
- Never start the eng ine when the vehicle is
raised, which could cause an accident .
- Support the veh icle securely with appropri
ate stands if work is to be performed under-
360
neath the vehicle; otherwise, there is a po
tential risk for injury.
- Never use the jack supplied with your Audi
on another vehicle, particularly on a heavier
one. The jack is only suitab le for use on the
veh icle it came with.
{!) Tips
The vehicle jack in your vehicle is mainte
nance-free.
Tire mobility kit
Preparation
.,. Read and follow the important safety precau-
tions ~
page 360 .
.,. Set the parking brake.
... Select the P selector lever position .
... Check if a repair with the tire mobility kit is pos
sible
~ page 360.
Using the tire mobility kit
Fig. 277 Tire: tire damage that cannot be repaired
The tire repair is on ly meant for temporary use.
Change the spare tire as soon as possible~&. .
If the tire is pierced by an object such as a nail,
do not remove the object from the tire .
U) ,... .. ~
" 00 m
The tire mobility kit may be used at temperatu res
as low as -4°F (-20°C).
The tire mobility kit may not be used:
-if the tire has cuts or punctures that are larger
than 0.16 in (4 mm)
(D ~ fig . 277
- if the rim is damaged
@
- if you drove with very low tire pressure or with-
out air in the tire ® ..,.
u (0 ...... N r--. N ...... 0
0
:E
Service Facility for assistance in these situations.
A WARNING
- Please note that the tire mob ility kit cannot
be used in all situations, and that it may on
ly be used temporarily.
- The tire sealant must not come in contact
with sk in, eyes, or clothes.
- If tire sealant gets in your eyes or on your
sk in, thoroughly rinse the affected area im
med iately w ith clean water.
- Do not inhale the fumes.
- If you swallow any of the t i re sealant, thor-
o ughly rinse yo ur mouth immediately and
drink a lot of water. Do not induce vomiting .
Seek medical attention immediately.
- Change your clothes immed iate ly if they get
t ire sealant on them.
- If an allergic reaction occurs , seek immedi
ate medical attention.
- Keep the tire sea lant away from children .
@ Tips
-If sealant lea ks, allow it to dry in pl ace. Yo u
ca n the n pee l it off like a sticker.
- Note the e xpiration date on the sealant bot
t le . Repl ace the tire sea lant a t an author
i zed Audi dealer or author ized Audi Se rvice
Facility .
- Radio reception can be interrupted when
operating the compressor.
- Obey all laws.
Repairing tires
Fig . 278 Co mponents of t he t ire mobility k it
Em ergen cy a ssis tanc e
Fig. 279 Tire mobil ity k it connect ion
Requirement: the tire mobility kit must be laid
out and ready fo r use ¢
page 360 .
Installing the tire mobility k it
.,. Open the cover @ on the compressor
¢fig . 2 78 .
.,. Remove the connector © and pressure hose ®
w ith pressure gauge from the housing.
.,. Insta ll the compressor press ure hose ® onto
t he flange @ on the t ire sealan t bot tle (!) .
.,. Insert the sea lant bottle with the flange at the
bottom into the opening ® on t he compressor
cover .
.. Remove the valve cap from the faulty t ire.
.. Install the filler hose@on the valve
0
¢fig. 279.
.,. Connect the plug©¢
fig. 2 78 to a n outlet in
the vehicle.
.,. Switch the ignit ion on .
Inflating a tire
.. Move the switch@¢ fig. 2 79 on the compres
sor into position
I.
.,. Inflate the tires to between 29 psi (200 k PA)
and 36 ps i (250 kPA) and read the pressure on
the gauge .
.,. If th is tire press ure is not re ached, remove the
fi ller hose. Drive slowly appro ximately 33 feet
( 1 0 m) forward or in reverse so that the sea lant
can be distr ibuted in the tire. Pump up the tire
aga in ¢ ,& .
A WARNING
--Read and follow the manufacturer's safety
precautions on the compressor and in the instr uctions on the bottle of sealant .
361
Emergency assistance
-If a tire pressure of 29 psi (200 kPA) cannot
reached after inflating for 6 minutes, then
the tire is too severely damaged. Do not
continue driving.
- If the tire cannot be repaired with the tire
sealant, see an authorized Audi dealer or au
thorized Audi Service Facility for ass istance.
(D} Tips
Do not operate the compressor for more than
six minutes continuously, or it can overheat.
Once the compressor has cooled, you can con
tinue to use it .
Completing
"' Adhere the sticke r that says "max . SO mph
(max. 80 km/h)" that is provided w ith the tir e
mobility kit within the driver's fie ld of vision.
"'S top the vehicle after driving for about 10 mi
nutes and check the tire pressure .
"' If the tire pressure is lower than 19 psi (130
kPA), then the tire is too severely damaged. Do
not continue driving.
A WARNING
Pay attention to the following after repairing
the tire :
- Do not drive faster than SO mph (80 km/h).
- Avoid hard acceleration, braking sharply, and fast cornering.
- The vehicle may become more difficult to
control.
- If the tire is too severely damaged, see an
authorized Audi dealer or authorized Aud i
Service Facility for assistance .
@ For the sake of the environment
You can give the used tire sealant bottle to an
authorized Audi dealer or authorized Audi
Service Facility for disposal.
@ Tips
Remember to obtain a new bottle of sealant
from an authorized Audi dea ler or authorized
Audi Service Facility after repairing a tire.
362
Replacing a wheel
' Preparation
You must complete the preparation before
changing a tire .
"'Read and follow the important safety precau-
tions¢
page 360.
"' Set the park ing brake.
"' Select the P selector lever posit ion.
"' When towing a trailer: disconnect the trailer
from your vehicle.
"' Lay out the vehicle tool kit¢
page 360 and the
spare tire.
"' Switch on wheel change mode* in the Infotain
ment system:
! MENUI button> Vehicle> left
control button >
Service & checks > Air suspen
sion: wheel change.
"'Switch the ignition off.
The vehicle jack mode* switches off automatical ly at speeds above 6 mph (10 km/h).
A WARNING
When using the ve hicle jack* on a road with a
steep hill or offroad, you must take extra pre
cautions to prevent the vehicle from rolling. Use suitable objects to block the front and
back of the wheel that is diagonal from the
wheel with the flat tire.
A WARNING
You or your passengers could be injured while
changing a whee l if you do not follow these
safety precautions:
- If you have a flat tire, move a safe distance
off the road. Turn off the engine, turn the
emergency f lashers on and use other warn
ing devices to alert other motorists.
- Make sure that passengers wait in a safe
place away from the vehicle and well away
from the road and traffic.
- To help prevent the vehicle from moving
suddenly and possibly slipping off the jack*,
always fully set the parking brake and block
the front and back of the wheel diagonally opposite the wheel being changed. When
one front wheel is lifted off the ground,
~
u (0 ...... N r--. N ...... 0
0
:E
(Park) will
not prevent the vehicle from
moving.
- Before you change a wheel , be sure the
ground is level and firm. If necessary, use a
sturdy board under the jack*.
-Always store the veh icle tool kit, the jack*
and the replaced tire in the luggage com
partment
c::> page 261 .
(D Tips
-Obey all laws .
- Before changing the wheel, you must acti- vate the jacking mode*, so that the a uto
matic controls for the air suspension * do
not make it more diff icu lt to lift the vehicle
with the jack*
c::> page 363 .
Removing the caps
Fig . 280 Whee l: whee l bo lts w it h c aps
"'Slide the plastic clip (from the vehicle tool kit)
onto the cap until it engages
c::> fig. 280 .
"'Remove the cap with the plastic clip .
Loosening the wheel bolts
Fig . 28 1 Whee l: loose ning the w hee l bo lt
Em ergen cy a ssis tanc e
"' Slide the wheel wrench (from the vehicle tool
kit) a ll the way onto the wheel bolt.
"' Turn the whee l bolt approximately one turn to
the left -arrow- . To reach the required to rque,
hold the end of the wheel wrench . If the wheel
bolt will not loosen, press carefully on the
wheel wrench with your foot . H old onto the ve
hicle secu rely whi le during th is and make sure
your stance is stable .
_& WARNING
To reduce the risk of an a cciden t, only loosen
the wheel bolts gently (one t urn) before rais
ing the vehicle with the vehicle jack* .
Raising the vehicle
Fig. 282 S ill panels : ma rki ngs
F ig. 283 Sill : po siti onin g t he ve hi cle jack
"' Place the veh icle jack* (vehicle tool kit) on a
firm surface. Use a flat, stab le support if neces
sary . On a slipp ery surface such as ti le, you
should use a non -slip pad (such as a rubber
mat)
¢ ,& .
"' Find the marking on the sill that is closest to
the tire that w ill be changed
c::> fig. 282 . Behind
the mark ing, there is a lifting point o n the side
sill for the veh icle jack* . .,.
363