2016 NISSAN NOTE turn signal

MWI
DIAGNOSIS SYSTEM (COMBINATION METER)MWI-73
< SYSTEM DESCRIPTION > [TYPE B]
C
D
E
F
G H
I
J
K L
M B A
O P
NOTE:
Some items are not available according to vehicle specification.
WORK SUPPORT
WARNING HISTORY
W/L ON HISTORY
• Stores histories when warning/indicator lamp is turned on.
• “W/L ON HISTORY” indicates the “TIME” when the warning/ indicator lamp is turned on.
• The “TIME” above is:
- 0: The condition that the warning/indicator lamp has been turned on 1 or more times after starting the engine and waiting for 30 seconds.
- 1 - 39: The number of times the engi ne was restarted after the 0 condition.
- NO W/L ON HISTORY: Stores NO (0) turning on history of warning/indicator lamp.
NOTE:
• W/L ON HISTORY is not stored for approximately 30 seconds after the engine starts.
• Brake warning lamp does not store any history when the parking brake is applied or the brake fluid level gets
low.
FR FOG IND
[On/Off] Displays [ON/OFF] condition of front fog lamp indicator.
TPMS PRESS L
[On/Off] Displays [ON/OFF] condition of check tire pressure warning message.
Display item [Unit]
MAIN
SIGNALS Description
Work support item
Description
Outside air temperature diagnosis A possible malfunction can be narrowed down by following the displayed instructions.
Fuel meter diagnosis(Analog pointer)
Warning lamp diagnosis
Display item Description
W/L ON HISTORY Lighting history of warning lamp and indicator lamp can be checked.
Revision: August 2015 2016 Versa Note

cardiagn.com

MWI-74
< ECU DIAGNOSIS INFORMATION >[TYPE B]
COMBINATION METER
ECU DIAGNOSIS INFORMATION
COMBINATION METER
Reference ValueINFOID:0000000012432613
VALUES ON THE DIAGNOSIS TOOL
Monitor Item Display contentData monitor
Condition Reference value in normal operation
SPEED METER
[mph or km/h] Speed meter
operation
While driving
Vehicle speed matches speed meter
SPEED OUTPUT
[mph or km/h] Vehicle speed While driving The speed output signal value via CAN
communication is approx. value of ve-
hicle speed.
ODO OUTPUT
[mph or km/h] ODO meter op-
eration
Driving
Distance driven
TACHO METER
[rpm] Ta c h o m e t e r
operation
Engine running The tacho meter is approx. value of en-
gine speed via CAN communication.
FUEL METER
[L] Fuel level Ignition ON Fuel level is approx. value of fuel
gauge.
W TEMP METER
[ ° F] or [ °C] Engine coolant
temperature
Engine running Input value of engine coolant tempera-
ture signal via CAN communication.
ABS W/L ABS warning
lampWhen ABS warning lamp is ON
On
When ABS warning lamp is OFF Off
VDC/TCS IND VDC indicator
lampWhen VDC indicator lamp is ON
On
When VDC indicator lamp is OFF OFF
SLIP IND Slip indicator
lampWhen SLIP indicator lamp is ON
On
When SLIP indicator lamp is OFF Off
BRAKE W/L Brake warning
lamp When Brake warning lamp is ON
On
*
When Brake warning lamp is OFF Off
DOOR W/L Door open
warning lampWhen Door warning lamp is ON
On
When Door warning lamp is OFF Off
HI-BEAM IND HI-Beam indi-
cator lampWhen High-beam indicator lamp is ON
On
When High-beam indicator lamp is OFF Off
TURN IND Turn signal in-
dicatorWhen Turn signal indicator lamp is ON
On
When Turn signal indicator lamp is OFF Off
LIGHT IND Light indicatorWhen Tail lamp indicator lamp is ON
On
When Tail lamp indicator lamp is OFF Off
FR FOG IND Front fog lamp
indicatorFront fog lamp indicator lamp ON
On
Front fog lamp indicator lamp OFF Off
OIL W/L Engine oil pres-
sure warning
light When engine oil pressure warning lamp is
ON
On
When engine oil pressure warning lamp is
OFF Off
MIL MIL warning
lampWhen Malfunction indi
cator lamp (MIL) is
ON On
When Malfunction indi cator lamp (MIL) is
OFF Off
Revision: August 2015
2016 Versa Note

cardiagn.com

MWI
COMBINATION METERMWI-77
< ECU DIAGNOSIS INFORMATION > [TYPE B]
C
D
E
F
G H
I
J
K L
M B A
O P
*1:For Canada
Fail-safeINFOID:0000000012432614
The combination meter activates the fail-safe contro l if CAN communication with each unit is malfunctioning.
DTC IndexINFOID:0000000012432615
Function Specifications
Speedometer Reset to zero by suspending communication.
Tachometer
Illumination control When suspending communication, changes to nighttime mode.
Shift position indicator When suspending communication, not indicate.
Information display Trip com-
puterCurrent fuel consump-
tion
• When reception time of an abnormal signal is 2 seconds or
less, the last received datum is used for calculation to indi-
cate the result.
• When reception time of an abnormal signal is more than two seconds, the last result calculated during normal condition is
indicated.
Average fuel consump-
tion
Distance to empty
Odo/trip meter An indicated value is maintained at communications blackout.
Buzzer The buzzer turns OFF by suspending communication.
Warning lamp/indicator lamp ABS warning lamp
The lamp turns ON by suspending communication.
Slip indicator lamp
Malfunction indicator lamp (MIL)
VDC OFF indicator lamp
EPS warning lamp
Brake warning lamp
High beam indicator lamp
The lamp turns OFF by suspending communication.
Turn signal indicator lamp
Door warning lamp
Light indicator lamp
Engine oil pressure warning lamp
High water temperature warning
lamp
Key warning lamp
O/D OFF indicator lamp
Shift P warning lamp
Engine start operation indicator lamp
Display contents of CONSULT
Diagnostic item is detected when... Refer to
CAN COMM CIRCUIT
[U1000] When combination meter is not transmitting or receiving CAN communication signal for
2 seconds or more.
MWI-93
CONTROL UNIT (CAN)
[U1010]When detecting error during the initial diagnosis of the CAN controller of combination
meter.
MWI-94
VEHICLE SPEED
[B2205]The abnormal vehicle speed signal is input from the ABS actuator and electric unit (con-
trol unit) for 2 seconds or more.
MWI-95
ENGINE SPEED
[B2267]If ECM continuously transmits abnormal engine speed signals for 2 seconds or more.
MWI-96
WATER TEMP
[B2268]If ECM continuously transmits abnormal engine coolant temperature signals for 60 sec-
onds or more.
MWI-97
Revision: August 2015
2016 Versa Note

cardiagn.com

MWI
POWER SUPPLY AND GROUND CIRCUITMWI-99
< DTC/CIRCUIT DIAGNOSIS > [TYPE B]
C
D
E
F
G H
I
J
K L
M B A
O P
nosis ProcedureINFOID:0000000012542966
Regarding Wiring Diagram information, refer to BCS-117, "Wiring Diagram".
1.CHECK FUSES AND FUSIBLE LINK
Check that the following fuses and fusible link are not blown.
Is the fuse blown?
YES >> Replace the blown fuse or fusible link after repairing the affected circuit.
NO >> GO TO 2.
2.CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connectors.
3. Check voltage between BCM connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair harness or connector.
3.CHECK GROUND CIRCUIT
Check continuity between BCM connector and ground.
Is the inspection result normal?
YES >> Inspection End.
NO >> Repair harness or connector.
BCM (BODY CONTROL SYSTEM) (W ITH INTELLIGENT KEY SYSTEM)
BCM (BODY CONTROL SYSTEM) (WITH IN TELLIGENT KEY SYSTEM) : Diagnosis
Procedure
INFOID:0000000012542967
Regarding Wiring Diagram information, refer to BCS-52, "Wiring Diagram".
Terminal No.Signal nameFuses and fusible link No.
37 Battery power supply 8 (10A)
42 12 (10A)
50 G (40A)
11 Ignition switch ACC or ON 18 (10A)
38 Ignition switch ON or START 2 (10A)
BCMGround Ignition switch position
Connector Terminal
—OFF
ACC ON
M18 11
0 V
Battery voltage
Battery voltage
37
Battery voltage
38 0 V0 V
M19 42
Battery voltage Battery voltage
50
BCM GroundContinuity
Connector Terminal
M19 55—Yes
Revision: August 2015 2016 Versa Note

cardiagn.com

MWI
FUEL LEVEL SENSOR SIGNAL CIRCUITMWI-101
< DTC/CIRCUIT DIAGNOSIS > [TYPE B]
C
D
E
F
G H
I
J
K L
M B A
O P
FUEL LEVEL SENSOR SIGNAL CIRCUIT
DescriptionINFOID:0000000012432636
The fuel level sensor unit and fuel pump detects the approx imate fuel level in the fuel tank and transmits the
fuel level signal to the combination meter.
Component Function CheckINFOID:0000000012432637
1.COMBINATION METER INPUT SIGNAL
1. Select METER/M&A on CONSULT.
2. Using FUEL METER of DATA MONITOR, compare the DATA MONITOR value with the fuel gauge posi- tion.
Does monitor value match fuel gauge reading?
YES >> Inspection End.
NO >> Replace combination meter. Refer to MWI-115, "
Removal and Installation".
Diagnosis ProcedureINFOID:0000000012432638
Regarding Wiring Diagram information, refer to MWI-79, "Wiring Diagram".
1.CHECK HARNESS CONNECTOR
1. Turn ignition switch OFF.
2. Check combination meter and fuel level sensor unit terminals (meter-side and harness-side) for poor con- nection.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace terminals or connectors.
2.CHECK FUEL LEVEL SENSOR UNIT CIRCUIT
1. Disconnect combination meter harness connector M24 and fuel level sensor unit and fuel pump harness
connector B44.
2. Check continuity between combination meter harness connector M24 terminal 6 and fuel level sensor unit
and fuel pump harness connector B44 terminal 2.
3. Check continuity between fuel level sensor unit and fuel pump harness connector B44 terminal 2 and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair harness or connector.
Fuel gauge indication position Reference value of data monitor [L]
1A pp ro x. 3 9.7
3/4 Approx. 32.9
1/2 Approx. 22.7
1/4 Approx. 11.9
0A ppro x. 2 .7
Connector TerminalConnector Terminal Continuity
M24 6B44 2Yes
Connector Terminal
GroundContinuity
B44 2 No
Revision: August 2015 2016 Versa Note

cardiagn.com

MWI-104
< DTC/CIRCUIT DIAGNOSIS >[TYPE B]
AMBIENT SENSOR SIGNAL CIRCUIT
AMBIENT SENSOR SIGNAL CIRCUIT
DescriptionINFOID:0000000012432641
The ambient sensor detects outside air temperature and c
onverts it into a resistance value which is then input
into the combination meter.
Diagnosis ProcedureINFOID:0000000012432642
Regarding Wiring Diagram information, refer to MWI-79, "Wiring Diagram".
1.CHECK AMBIENT SENSOR POWER SUPPLY
1. Turn ignition switch OFF.
2. Disconnect ambient sensor connector.
3. Turn ignition switch ON.
4. Check voltage between ambient sensor harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 2.
2.CHECK AMBIENT SENSOR POWER SUPPLY FOR OPEN OR SHORT
1. Turn ignition switch OFF.
2. Disconnect combination meter connec tor and ambient sensor connector.
3. Check continuity between combination meter harness connector and ambient sensor harness connector.
4. Check continuity between combination meter harness connector and ground.
Is the inspection result normal?
YES >> Replace combination meter. Refer to MWI-115, "Removal and Installation".
NO >> Repair or replace harness or connector.
3.CHECK AMBIENT SENSOR GROUND CIRCUIT
Check continuity between combination meter har ness connector and ambient sensor harness connector.
Is the inspection result normal?
YES >> Inspection End.
NO >> Repair or replace harness or connector.
+ −Vo l ta g e
(Approx.)
Ambient sensor
Connector Terminal
E69 1 Ground 5 V
Combination meter Ambient sensor
Continuity
Connector TerminalConnector Terminal
M24 19E69 1Yes
Combination meter
GroundContinuity
Connector Terminal
M24 19 No
Combination meterAmbient sensor
Continuity
Connector TerminalConnector Terminal
M24 20E69 2Yes
Revision: August 2015 2016 Versa Note

cardiagn.com

MWI
AMBIENT SENSOR SIGNAL CIRCUITMWI-105
< DTC/CIRCUIT DIAGNOSIS > [TYPE B]
C
D
E
F
G H
I
J
K L
M B A
O P
Component InspectionINFOID:0000000012432643
1.CHECK AMBIENT SENSOR
1. Turn ignition switch OFF.
2. Disconnect ambient sensor connector.
3. Check resistance between ambient sensor terminals.
Is the inspection result normal?
YES >> Inspection End.
NO >> Replace ambient sensor. Refer to MWI-116, "
Removal and Installation".
Te r m i n a lCondition
Resistance: kΩ
Temperature: °C ( °F)
12
− 15 (5) 12.73
− 10 (14) 9.92
− 5 (23) 7.80
0 (32) 6.19
5 (41) 4.95
10 (50) 3.99
15 (59) 3.24
20 (68) 2.65
25 (77) 2.19
30 (86) 1.81
35 (95) 1.51
40 (104) 1.27
45 (113) 1.07
Revision: August 2015 2016 Versa Note

cardiagn.com

MWI-106
< DTC/CIRCUIT DIAGNOSIS >[TYPE B]
WASHER FLUID LEVEL SWITCH CIRCUIT
WASHER FLUID LEVEL SWITCH CIRCUIT
DescriptionINFOID:0000000012432644
Transmits the washer fluid level switch signal to the combination meter.
Diagnosis ProcedureINFOID:0000000012432645
Regarding Wiring Diagram information, refer to
MWI-79, "Wiring Diagram".
1.CHECK WASHER FLUID LEVEL SWITCH SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect combination meter connector and washer fluid level switch connector.
3. Check continuity between combination meter harne ss connector M24 terminal 17 and washer fluid level
switch harness connector E50 terminal 1.
4. Check continuity between combination meter harness connector M24 terminal 17 and ground.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness or connector.
2.CHECK WASHER FLUID LEVEL SWITCH GROUND CIRCUIT
Check continuity between washer fluid level switch harness connector E50 terminal 2 and ground.
Is the inspection result normal?
YES >> Inspection End.
NO >> Repair or replace harness or connector.
Component InspectionINFOID:0000000012432646
1.CHECK WASHER FLUID LEVEL SWITCH
Check continuity between washer fluid level switch terminals 1 and 2.
Is the inspection result normal?
YES >> Inspection End.
NO >> Replace washer fluid level switch. Refer to WW-59, "
Removal and Installation".
ConnectorTerminalConnector Terminal Continuity
M24 17E50 1Yes
Connector Terminal
GroundContinuity
M24 17 No
ConnectorTerminal
GroundContinuity
E50 2 Yes
TerminalWasher fluid level Continuity
1 - 2 Low
Yes
High No
Revision: August 2015 2016 Versa Note

cardiagn.com