2016 NISSAN NOTE keyless

PREPARATIONDLK-11
< PREPARATION > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
PREPARATION
PREPARATION
Special Service ToolsINFOID:0000000012429963
The actual shape of the tools may differ from those illustrated here.
Tool number
(TechMate No.)
Tool name Description
—
(J-39570)
Chassis Ear Locating the noise
—
(J-50397)
NISSAN Squeak and Rattle Kit Repairing the cause of noise
—
(J-43241)
Remote Keyless Entry Tester Used to test keyfobs
—
(J-50190)
Signal Tech II • Activate and display TPMS transmitter
IDs
• Display tire pressure reported by the TPMS transmitter
• Read TPMS DTCs
• Register TPMS transmitter IDs
• Test remote keyless entry keyfob rela- tive signal strength
• Compatible with future sensors
• Equipped with a display
• Check Intelligent Key relative signal strength
• Confirm vehicle Intelligent Key anten- na signal strength
SIIA0993E
ALJIA1232ZZ
LEL946A
ALEIA0131ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

COMPONENT PARTSDLK-15
< SYSTEM DESCRIPTION > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
INTELLIGENT KEY SYSTEM : Inside Key Antenna (Instrument Center)INFOID:0000000012429966
• Inside key antenna (instrument center) detects that Intelligent Key
is within the inside detection area, and then transmits detection
status to BCM.
• Inside key antenna (instrument center) is installed in the rear of cluster lid C of instrument center.
7. Back door lock actuator Back door lock actuator locks/unlocks the back door
latch assembly.
8. Inside key antenna (instrument center) Inside key antenna (instrument center) detects
whether Intelligent Key is inside the vehicle or not,
and then transmits the signal to the BCM.
Refer to
DLK-15, "
INTELLIGENT KEY SYSTEM :
Inside Key Antenna (Instrument Center)".
9. Remote keyless entry receiver Remote keyless entry receiver receives button op-
eration signal and key ID signal of Intelligent Key,
and them transmits them to the BCM.
Refer to
DLK-17, "
INTELLIGENT KEY SYSTEM :
Remote Keyless Entry Receiver".
10. Intelligent Key warning buzzer Intelligent Key warning buzzer warns the user, who
is outside the vehicle, of operation confirmation ac-
cording to Intelligent Key operation and door re-
quest switch operation, or of an inappropriate
operation.
Refer to
DLK-17, "
INTELLIGENT KEY SYSTEM :
Intelligent Key Warning Buzzer".
11. Outside key antenna LH Outside key antenna (LH) detects whether Intelli-
gent Key is outside the vehicle or not, and then
transmits the signal to the BCM.
Refer to
DLK-16, "
INTELLIGENT KEY SYSTEM :
Outside Key Antenna (Driver Side)".
12. Door request switch Door request switch transmits door lock/unlock re-
quest signal to the BCM.
13. Door switch Door switch detects door open/close condition and
then transmits ON/OFF signal to BCM.
14. Outside key antenna (rear bumper) Outside key antenna (Rear bumper) detects wheth-
er Intelligent Key is outside the vehicle or not, and
then transmits the signal to the BCM.
Refer to
DLK-16, "
INTELLIGENT KEY SYSTEM :
Outside Key Antenna (Rear Bumper)".
15. Back door request switch Back door request switch transmits door lock/unlock
request signal to the BCM.
16. Inside key antenna (trunk room) Inside key antenna (trunk room) detects whether In-
telligent Key is inside the vehicle or not, and then
transmits the signal to the BCM.
Refer to
DLK-16, "
INTELLIGENT KEY SYSTEM :
Inside Key Antenna (Trunk Room)".
17. Inside key antenna (console) Inside key antenna (console) detects whether Intel-
ligent Key is inside the vehicle or not, and then
transmits the signal to the BCM.
Refer to
DLK-16, "
INTELLIGENT KEY SYSTEM :
Inside Key Antenna (Console)".
No.
Component Function
JMKIA8646ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

COMPONENT PARTSDLK-17
< SYSTEM DESCRIPTION > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
INTELLIGENT KEY SYSTEM : Outsi de Key Antenna (Passenger Side)INFOID:0000000012429971
• Outside key antenna RH detects that Intelligent Key is within the
outside detection area, and then transmits detection status to
BCM. Request signal is transmitted simultaneously to Intelligent
Key.
• Outside key antenna RH is installed in front outside handle RH.
INTELLIGENT KEY SYSTEM : Front Do or Lock Assembly (Driver Side)INFOID:0000000012429972
• Door lock actuator and unlock sensor are Integrated in front door
lock assembly LH.
• Door lock actuator receives lock/unlock signal from BCM, and then
locks/unlocks driver door.
• Only front door lock assembly LH integrates unlock sensor. Unlock sensor transmits lock/unlock status of LH door to BCM.
INTELLIGENT KEY SYSTEM : Remote Keyless Entry ReceiverINFOID:0000000012429973
• Remote keyless entry receiver receives button operation signal
and key ID signal of Intelligent Key, and then transmits them to
BCM.
• Remote keyless entry receiver is installed in the rear of glove box
lid.
INTELLIGENT KEY SYSTEM : Intelligent Key Warning BuzzerINFOID:0000000012429974
• Intelligent Key warning buzzer warns the user, who is outside vehi-cle, of operation confirmation according to Intelligent Key operation
and door request switch operation, or of an inappropriate opera-
tion.
• Intelligent Key warning buzzer is installed in the rear of front bumper and behind LH headlight.
JMKIA8648ZZ
JMKIA8649ZZ
JMKIA8647ZZ
JMKIA8650ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-22
< SYSTEM DESCRIPTION >[WITH INTELLIGENT KEY SYSTEM]
SYSTEM (INTELLIGENT KEY SYSTEM)
SYSTEM (INTELLIGENT KEY SYSTEM)
INTELLIGENT KEY SYSTEM
INTELLIGENT KEY SYSTEM : System DescriptionINFOID:0000000012429983
SYSTEM DIAGRAM
SYSTEM DESCRIPTION
• The Intelligent Key system is a system that makes it
possible to lock and unlock the door locks (door lock/
unlock function) by carrying the Intelligent Key, which operates based on the results of electronic ID verifica-
tion using two-way communication between the Intelligent Key and the vehicle (BCM).
NOTE:
The driver should always carry the Intelligent Key.
• The settings for each function can be changed with CONSULT.
• If an Intelligent Key is lost, a new Intelligent Key can be registered. A maximum of 4 Intelligent Keys can be
registered.
• It is possible to perform a diagnosis on the syst em and register an Intelligent Key with CONSULT.
• For initialization and registration of Intelligent Keys, refer to CONSULT Immobilizer mode and follow the on-
screen instructions.
ALKIA3645GB
Function DescriptionRefer
Door lock Lock/unlock can be performed by pressing the request switch. DLK-23
Remote keyless entryLock/unlock can be performed by pressing the remote controller button of the
Intelligent Key.
DLK-25
Revision: August 2015
2016 Versa Note

cardiagn.com

SYSTEM (INTELLIGENT KEY SYSTEM)DLK-23
< SYSTEM DESCRIPTION > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
DOOR LOCK FUNCTION
DOOR LOCK FUNCTION : System DescriptionINFOID:0000000012429984
SYSTEM DIAGRAM
DOOR REQUEST SWITCH OPERATION
When pressing the request switch, it is possible to lock and unlock the door by carrying the Intelligent Key.
OPERATION DESCRIPTION
• When the BCM detects that each door request switch is pressed, it starts the outside key antenna and inside
key antenna corresponding to the pressed door request swit ch and transmits the request signal to the Intelli-
gent Key. And then, check that the Intelligent Key is near the door.
• If the Intelligent Key is within the outside key antenna detection area, it receives the request signal and
transmits the key ID signal to the BCM via remote keyless entry receiver.
• BCM receives the key ID signal and compares it with the registered key ID.
• BCM transmits door lock/unlock signal and operates each door lock actuator. At the same time, BCM blinks
hazard warning lamp (lock: 2 times, unlock: 1 time) and sounds Intelligent Key buzzer (lock: 1 time, unlock:
1 time) as a reminder.
OPERATION CONDITION
If the following conditions are satisfied, door lock/unl ock operation is performed if the door request switch is
operated:
Key reminder The key reminder buzzer sounds a warning if the door is locked with the key left
inside the vehicle. DLK-27
WarningIf an action that does not meet the operating condition of the Intelligent Key sys-
tem is taken, the buzzer sounds to inform the driver.
DLK-27
Engine start
The engine can be turned on while carrying the Intelligent Key. DLK-22
Interior room lamp control Interior room lamp is controlled according to door lock/unlock state. DLK-20
FunctionDescriptionRefer
JMKIA6137GB
Revision: August 2015 2016 Versa Note

cardiagn.com

SYSTEM (INTELLIGENT KEY SYSTEM)DLK-25
< SYSTEM DESCRIPTION > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
REMOTE KEYLESS ENTRY FUNCTION
REMOTE KEYLESS ENTRY FUNCT ION : System DescriptionINFOID:0000000012429985
SYSTEM DIAGRAM
REMOTE KEYLESS ENTRY OPERATION
The Intelligent Key has the same functions as the remote control entry system. Therefore, it can be used in the
same manner as the remote controller by operating the door lock/unlock button.
Remote keyless entry system contro ls operation of the following items:
• Auto door lock
• Door lock/unlock
• Hazard and buzzer reminder
OPERATION AREA
To check that the Intelligent Key works normally, us e within 1 m (3 ft) range of each door, however the opera-
ble range may differ according to surroundings.
DOOR LOCK/UNLOCK FUNCTION
• When door lock/unlock button of the Intelligent Key is pressed, lock signal or unlock signal is transmitted from Intelligent Key to BCM via remote keyless entry receiver.
• BCM receives the signal and compares it with the registered key ID to the vehicle.
• BCM transmits door lock/unlock signal to each door lock actuator and operates each door lock actuator,
when key ID matches. At the same time, BCM blinks hazard warning lamps (lock: 2 times, unlock: 1 time)
and sounds Intelligent Key buzzer (lock: 1 time) as a reminder.
OPERATION CONDITION
Door lock function
Intelligent Key
Remote keyless entry receiver
Door switch
Door request switch
Door lock actuator
Inside key antenna
Outside key antenna
Intelligent Key warning buzzer
CAN communication system
BCM
Hazard warning lamp
Push-button ignition switch
Combination meter
Door lock/unlock function ××××××× ×
Hazard and buzzer reminder function ×××× ×
Auto door lock function ××××× × × ×
ALKIA3195GB
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-26
< SYSTEM DESCRIPTION >[WITH INTELLIGENT KEY SYSTEM]
SYSTEM (INTELLIGENT KEY SYSTEM)
HAZARD AND BUZZER REMINDER FUNCTION
For the operation check, BCM blinks hazard warning lamps (lock: 2 times, unlock: 1 time) and sounds Intelli-
gent Key warning buzzer (lock: 1 time) when door lock or unlock operates by each remote controller button
operation of Intelligent Key.
How to Change Hazard and Buzzer Reminder Mode
Refer to
BCS-22, "INTELLIGENT KEY : CONSULT Func tion (BCM - INTELLIGENT KEY)".
AUTO DOOR LOCK FUNCTION
After door is unlocked by Intelligent Key button operati on and if 30 seconds or more passes without performing
the following operation, all doors are automatically locked. However, operation check function does not acti-
vate.
Auto door lock mode can be changed by the “AUTO LOCK SET” in “Work support”. Refer to BCS-22, "
INTEL-
LIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)".
LIST OF OPERATION RELATED PARTS
Parts marked with × are the parts related to operation.
KEY REMINDER FUNCTION
Remote controller operation Operation condition
Lock • All door are closed.
• Ignition switch is in the LOCK or OFF position.
• P position warning is not activated.
Unlock • Ignition switch is in the LOCK or OFF position.
• Intelligent Key is outside the vehicle.
• P position warning is not activated.
Operating condition
• Door switch is ON. (door is open)
• BCM receives lock signal.
• Push switch is pressed.
Remote keyless entry functions
Intelligent Key
Remote keyless entry receiver
Door switch
Door lock actuator
Push-button ignition switch
Intelligent Key warning buzzer
CAN communication system
BCM
Combination meter
Hazard warning lamp
IPDM E/R
Horn
Door lock/unlock function by remote control button
××××××
Hazard and buzzer reminder function ×××××××
Auto door lock function ××××××
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-32
< SYSTEM DESCRIPTION >[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
DATA MONITOR
ACTIVE TEST
Monitor Item [Unit]
Main Description
REQ SW -DR [On/Off] ×Indicates condition of door request switch LH.
REQ SW -AS [On/Off] ×Indicates condition of door request switch RH.
REQ SW -BD/TR [On/Off] ×Indicates condition of back door request switch.
PUSH SW [On/Off] Indicates condition of push-button ignition switch.
CLUCH SW [On/Off] ×Indicates condition of clutch interlock switch.
BRAKE SW 1 [On/Off] ×Indicates condition of brake switch.
BRAKE SW 2 [On/Off] Indicates condition of brake switch.
DETE/CANCL SW [On/Off] ×Indicates condition of P (park) position.
SFT PN/N SW [On/Off] ×Indicates condition of P (park) or N (neutral) position.
UNLK SEN -DR [On/Off] ×Indicates condition of door unlock sensor.
PUSH SW -IPDM [On/Off] Indicates condition of push-button ignition switch received from IPDM E/R on
CAN communication line.
IGN RLY1 -F/B [On/Off] Indicates condition of ignition relay 1 received from IPDM E/R on CAN commu-
nication line.
DETE SW -IPDM [On/Off] Indicates condition of detent switch received from TCM on CAN communication
line.
SFT PN -IPDM [On/Off] Indicates condition of P (park) or N (neutral) position from TCM on CAN com-
munication line.
SFT P -MET [On/Off] Indicates condition of P (park) position from TCM on CAN communication line.
SFT N -MET [On/Off] Indicates condition of N (neutral) position from IPDM E/R on CAN communica-
tion line.
ENGINE STATE [Stop/Start/Crank/Run] ×Indicates condition of engine state from ECM on CAN communication line.
VEH SPEED 1 [mph/km/h] ×Indicates condition of ve
hicle speed signal receiv ed from ABS on CAN commu-
nication line.
VEH SPEED 2 [mph/km/h] ×Indicates condition of vehicle speed signal received from combination meter on
CAN communication line.
DOOR STAT -DR [LOCK/READY/UNLK] ×Indicates condition of driver side door status.
DOOR STAT -AS [LOCK/READY/UNLK] ×Indicates condition of passenger side door status.
ID OK FLAG [Set/Reset] Indicates condition of Intelligent Key ID.
PRMT ENG STRT [Set/Reset] Indicates condition of engine start possibility.
RKE OPE COUN1 [0-19] ×When remote keyless entry receiver receives the signal transmitted while oper-
ating on Intelligent Key, the numerical value start changing.
RKE OPE COUN2 [0-19] ×When remote keyless entry receiver receives the signal transmitted while oper-
ating on Intelligent Key, the numerical value start changing.
RKE-LOCK [On/Off] Indicates condition of lock signal from Intelligent Key.
RKE-UNLOCK [On/Off] Indicates condition of unlock signal from Intelligent Key.
RKE-PANIC [On/Off] Indicates condition of panic signal from Intelligent Key.
RKE-MODE CHG [On/Off] Indicates condition of mode change signal from Intelligent Key.
Test Item Description
INSIDE BUZZER This test is able to check combination meter warning chime operation [Take Out/Knob/Key/
Off].
LCD This test is able to check combination meter display in
formation [Off/LK WN/OUTKEY/NO
KY/BATT/INSRT/SFT P/ROTAT/ID NG/B&P I/B&P N].
BATTERY SAVER This test is able to check battery saver operation [On/Off].
Revision: August 2015 2016 Versa Note

cardiagn.com