2016 NISSAN NOTE ignition

DLK-256
< DTC/CIRCUIT DIAGNOSIS >[WITHOUT INTELLIGENT KEY SYSTEM]
KEYFOB ID SET UP WITH CONSULT
KEYFOB ID SET UP WITH CONSULT
ID Code Entry ProcedureINFOID:0000000012430224
KEYFOB ID SET UP WITH CONSULT
NOTE:
•
If a keyfob is lost, the ID code of the lost keyfob must be erased to prevent unauthorized use. A spe-
cific ID code can be erased with CONSULT. However, when the ID code of a lost keyfob is not known,
all controller ID codes should be erased. After all ID codes are erased, the ID codes of all remaining
and/or new keyfobs must be re-registered.
• When registering an additional keyfob, the existing ID codes in memory may or may not be erased. If
five ID codes are stored in memory when an additi onal code is registered, only the oldest code is
erased. If less than five codes are stored in memory when an additional code is registered, the new
ID code is added and no ID codes are erased.
• Entry of a maximum of five ID codes is allowed. Wh en more than five codes are entered, the oldest ID
code will be erased.
• Even if the same ID code that is already in memory is input, the same ID code can be entered. The
code is counted as an additional code.
1. Turn ignition switch ON.
2. Select “BCM”.
3. Select “MULTI REMOTE ENT”.
4. Select “Work support”.
5. You can register, erase or confirm a keyfob ID code. To register a new code, select the following option
and follow CONSULT instructions:
• REMO CONT ID REGIST Use this mode to register a keyfob ID code.
NOTE:
Register the ID code when keyfob or BCM is re placed, or when additional keyfob is required.
• REMO CONT ID ERASUR Use this mode to erase a keyfob ID code.
• REMO CONT ID CONFIR
Use this mode to confirm if a ke yfob ID code is registered or not.
Revision: August 2015 2016 Versa Note

cardiagn.com

POWER DOOR LOCK SYSTEM SYMPTOMSDLK-259
< SYMPTOM DIAGNOSIS > [WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
SYMPTOM DIAGNOSIS
POWER DOOR LOCK SYSTEM SYMPTOMS
Symptom TableINFOID:0000000012430226
DOOR LOCK/UNLOCK FUNCTION MALFUNCTION
NOTE:
• Before performing the diagnosis in the following table, check “WORK FLOW”. Refer to DLK-225, "
Work
Flow".
• Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and check each symptom.
• If the following symptoms are detec ted, check systems shown in the “Diagnosis/service procedure” column
in this order.
Symptom Diagnosis/service procedure Reference page
Key reminder door function does not operate
properly. 1. Check door switch.
DLK-232
2. Check key switch.DLK-241
3. Check Intermittent Incident. GI-42
Power door lock does not operate with door
lock and unlock switch on main power window
and door lock/unlock switch or power window
and door lock/unlock switch RH.1. Check BCM power supply and ground circuit.
BCS-1292. Check main power window and door lock and unlock switch. DLK-235
3. Check power window and door lock and unlock switch RH.DLK-236
4. Check Intermittent Incident. GI-42
Specific door lock actuator does not operate.1. Check door lock actuator.Front LH
DLK-242
Front RHDLK-243
Rear LHDLK-244
Rear RHDLK-245
2. Check Intermittent Incident. GI-42
Power door locks do not operate with front
door lock key cylinder switch LH.1. Check key cylinder switch.
DLK-239
2. Replace BCM.BCS-137
Vehicle speed sensing auto door LOCK oper-
ation does not operate.1. Ensure automatic door lock/unlock function (lock operation)
is enabled. DLK-196
2. Check combination meter vehicle speed signal. MWI-40
(Type
A)
MWI-95
(Type
B)
3. Check intermittent incident. GI-42
Ignition OFF interlock auto door UNLOCK
function does not operate.1. Ensure automatic door lock/unlock function (unlock opera-
tion) is enabled. DLK-196
2. Check BCM for DTCs.
BCS-115
3. Check intermittent incident. GI-42
Revision: August 2015 2016 Versa Note

cardiagn.com

FRONT DOORDLK-277
< REMOVAL AND INSTALLATION > [WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
FRONT DOOR
Exploded ViewINFOID:0000000012430241
DOOR ASSEMBLY
DOOR ASSEMBLY : Removal and InstallationINFOID:0000000012430242
CAUTION:
• Use two people when removing or inst alling front door due to its heavy weight
• When removing and installing front door assembl y, support the door using a suitable tool.
• Do not use air tools or electric tools for servicing.
• Before servicing, turn ignition sw itch off, disconnect both battery terminals and wait at least three
minutes.
REMOVAL
1. Disconnect the battery positive and negative terminal s and wait at least three minutes. Refer to PG-70,
"Removal and Installation (Battery)".
2. Remove dash side finisher. Refer to INT-24, "
DASH SIDE FINISHER : Removal and Installation".
3. Disconnect the harness connectors from the front door.
4. Remove door check link bolt (body side).
5. Remove door hinge nuts (door side) and front door assembly.
INSTALLATION
1. Inside seal 2. Door sash front tape 3. Grommet (driver side only)
4. Door upper hinge 5. Door lower hinge6. Door check link
7. Front door panel 8. Lower grommet9. Upper grommet
10. Door striker 11. Body panel plug12. Door sash rear tape
AWKIA2492ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

STEERING LOCK UNITDLK-311
< REMOVAL AND INSTALLATION > [WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
STEERING LOCK UNIT
Exploded ViewINFOID:0000000012828149
NOTE:
Steering lock unit and key cylinder are serviced as an a ssembly. Ignition switch is available separately.
Removal and Installation - Steering lock unitINFOID:0000000012828150
REMOVAL
1. Disconnect battery cables. Refer to PG-70, "Removal and Installation (Battery)".
2. Remove combination switch. Refer to BCS-138, "
Removal and Installation".
3. Remove cluster lid A. Refer to IP-21, "
Removal and Installation".
4. Disconnect the harness connector from the spiral cable.
5. Disconnect the harness connector from the ignition switch.
ALKIA4124ZZ
1. Steering lock bracket 2. Steering column 3. Ignition switch
4. Steering lock unit 5. NATS antenna amp. A. Tamper resistant self-shear type screw
B. Key cylinder Front
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-312
< REMOVAL AND INSTALLATION >[WITHOUT INTELLIGENT KEY SYSTEM]
STEERING LOCK UNIT
6. Disconnect the harness connector from the key switch.
7. For models with CVT but without intelligent key system,
perform the following steps to separate key inter-
lock cable from steering lock unit:
a. Lift lock plate (A) in the direction of the arrow ( C) and remove in the direction of the arrow ( D).
b. Disconnect the key interlock cable from the steering lock unit.
8. Using suitable tool, remove tamper resistant self-shear type screw. CAUTION:
Do not reuse screw. Replace with new tamper resistant self-shear type screw.
9. Remove steering lock bracket and steering lock unit.
10. Remove NATS antenna amp. (if necessary). Refer to SEC-159, "
Removal and Installation".
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse screw. Replace with new tamper resistant self-shear type screw.
• Tighten tamper resistant self-shear type screw until head breaks off.
• Adjust the neutral position of the steering angle sensor. Refer to BRC-55, "
ADJUSTMENT OF STEERING
ANGLE SENSOR NEUTRAL POSITION : Description".
• For initialization and registration of mechanical keys, refer to CONSULT Immobilizer mode and follow the on-
screen instructions.
Removal and Installation - Ignition switchINFOID:0000000012828152
REMOVAL
1. Remove steering column cover. Refer to IP-17, "Removal and Installation".
2. Disconnect ignition switch harness connector.
3. Remove ignition switch screws and ignition switch.
INSTALLATION
Installation is in the reverse order of removal.
Adjust the neutral position of t he steering angle sensor. Refer to BRC-55, "
ADJUSTMENT OF STEERING
ANGLE SENSOR NEUTRAL POSITION : Description".
(1) :Key interlock cable
(B) :Steering lock unit
JSDIA1798ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

EM-1
ENGINE
C
DE
F
G H
I
J
K L
M
SECTION EM
A
EM
N
O P
CONTENTS
ENGINE MECHANICAL
HR16DE
PRECAUTION ....... ........................................
3
PRECAUTIONS .............................................. .....3
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ............................................................. ......
3
Precaution for Procedure without Cowl Top Cover ......3
Draining Engine Coolant ...........................................3
Disconnecting Fuel Piping .........................................3
Removal and Disassembly ........................................3
Inspection, Repair and Replacement ........................4
Assembly and Installation .........................................4
Parts Requiring Angle Tightening ....................... ......4
Precaution for Liquid Gasket .....................................4
PREPARATION ............................................6
PREPARATION .............................................. .....6
Special Service Tools .......................................... ......6
Commercial Service Tools ........................................7
BASIC INSPECTION ...................................10
CAMSHAFT VALVE CLEARANCE ............... ....10
Inspection and Adjustment .................................. ....10
COMPRESSION PRESSURE ............................13
Inspection ............................................................ ....13
SYMPTOM DIAGNOSIS ..............................14
NOISE, VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING ........................ ....
14
NVH troubleshooting Chart ................................. ....14
PERIODIC MAINTENANCE .........................16
DRIVE BELT ................................................... ....16
Exploded View .................................................... ....16
Removal and Installation .........................................16
Inspection ............................................................ ....17
Adjustment ...............................................................17
AIR CLEANER FILTER .....................................19
Exploded View .........................................................19
Removal and Installation .........................................19
SPARK PLUG ...................................................21
Exploded View .........................................................21
Removal and Installation .........................................21
REMOVAL AND INSTALLATION ...............24
DRIVE BELT IDLER PULLEY ..........................24
Exploded View ..................................................... ....24
Removal and Installation .........................................24
AIR CLEANER AND AIR DUCT .......................26
Exploded View .........................................................26
Removal and Installation .........................................26
INTAKE MANIFOLD .........................................28
Exploded View .........................................................28
Removal and Installation .........................................28
EXHAUST MANIFOLD ......................................31
Exploded View .........................................................31
Removal and Installation .........................................31
OIL PAN AND OIL STRAINER .........................34
Exploded View .........................................................34
Removal and Installation (Lower Oil Pan) ...............34
Removal and Installation (Upper Oil Pan) ........... ....37
FUEL INJECTOR AND FUEL TUBE ................40
Exploded View .........................................................40
Removal and Installation .........................................40
IGNITION COIL .................................................47
Exploded View .........................................................47
Removal and Installation .........................................47
ROCKER COVER .............................................48
Revision: August 2015 2016 Versa Note

cardiagn.com

PRECAUTIONSEM-3
< PRECAUTION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EM
NP
O
PRECAUTION
PRECAUTIONS
Precaution for Supplemental
Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000012431679
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severi ty of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inoper ative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including in correct removal and installation of the SRS, can lead to personal
injury caused by unintentional act ivation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipm ent on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identi fied by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Un it or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or el ectric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor( s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery and wait at least three mi nutes before performing any service.
Precaution for Procedure without Cowl Top CoverINFOID:0000000012431680
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc.
Draining Engine CoolantINFOID:0000000012431681
Drain engine coolant and engine oil when the engine is cooled.
Disconnecting Fuel PipingINFOID:0000000012431682
• Before starting work, check no fire or spark producing items are in the work area.
• Release fuel pressure before disconnecting and disassembly.
• After disconnecting pipes, plug openings to stop fuel leakage.
Removal and DisassemblyINFOID:0000000012431683
• When instructed to use SST, use specified tools. Alwa ys be careful to work safely, avoid forceful or unin-
structed operations.
• Use care to avoid damage to mating or sliding surfaces.
PIIB3706J
Revision: August 2015 2016 Versa Note

cardiagn.com

COMPRESSION PRESSUREEM-13
< BASIC INSPECTION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EM
NP
O
COMPRESSION PRESSURE
InspectionINFOID:0000000012431691
1. Warm up engine to full operating temperature and then turn it off.
2. Release fuel pressure. Refer to
EC-137, "
Work Procedure".
3. Remove ignition coil and spark plug from each cylinder. Refer to EM-48, "
Exploded View".
4. Connect engine tachometer (not required in use of CONSULT).
5. Install compression gauge (B) with an adapter (A) into spark plug hole.
• Use an adapter with a diameter (a) smaller than 20 mm (0.79in). Otherwise, it may be caught by cylinder head during
removal.
6. With accelerator pedal fully depressed, turn ignition switch to »»» for cranking. When the gauge pointer stabilizes, read the compression pressure and the engi ne rpm. Perform these steps to check each cylin-
der.
CAUTION:
Always use a fully charged battery to obtain the specified engine speed.
• If the engine speed is out of the specified range, check the battery. Check the engine speed again with a
fully charged battery.
• If some cylinders have low compression pressure, pour a small amount of engine oil into the spark plug hole to recheck the compression.
- If the added engine oil improves the compression, the piston rings may be worn or damaged. Check the piston rings and replace if necessary.
- If the compression pressure remains low despite the addition of engine oil, the valves may be malfunc-
tioning. Check the valves for damage. Replace the valve or valve seat as necessary.
• If two adjacent cylinders have respectively low compression pressure and their compression remains low even after the addition of engine oil the head gasket may be leaking, or valves in adjacent cylinders
may be damaged. Inspect and repair as required.
• If the compression pressure is below the minimum value, check the valve clearances and parts associ-
ated with the combustion chamber (valve, valve seat , piston, piston ring, cylinder bore, cylinder head,
cylinder head gasket). After repairing, measure the compression pressure again.
7. After inspection is completed, install removed parts.
8. Start the engine, and ensure that the engine runs smoothly.
9. Perform trouble diagnosis. If DTC appears, erase it. Refer to EC-120, "
Work Flow".
JPBIA4119ZZ
(a) : Less than 20 mm (0.79 in)
JPBIA0171ZZ
Compression pressure : Refer to EM-116, "General Specification".
Revision: August 2015 2016 Versa Note

cardiagn.com