2016 NISSAN NOTE Heat

EM-6
< PREPARATION >[HR16DE]
PREPARATION
PREPARATION
PREPARATION
Special Service ToolsINFOID:0000000012431688
The actual shape of the tools may differ from those illustrated here.
Tool number
(TechMate No.)
Tool nameDescription
K V 1 0 1111 0 0
(J-37228)
Seal cutter Removing oil pan (lower and upper) etc.
KV10116200
(J-26336-B)
Valve spring compressor
1. KV10115900
(J-26336-20)
Attachment
2. KV10109220
( — )
Adapter Disassembling and assembling valve mecha-
nism
Part (1) is a component of KV10116200, but
Part (2) is not so.
KV10112100
(BT-8653-A)
Angle wrench Tightening bolts for main bearing cap, cylinder
head, etc.
KV10117100
( — )
Heated oxygen sensor wrench Loosening or tightening heated oxygen sen-
sor 1
For 22 mm (0.87 in) width hexagon nut
KV10107902
(J-38959)
Valve oil seal puller Removing valve oil seal
KV10115600
(J-38958)
Valve oil seal drift Installing valve oil seal
Use side A.
a: 20 (0.79) dia. d: 8 (0.31) dia.
b: 13 (0.51) dia. e: 10.7 (0.421)
c: 10.3 (0.406) dia. f: 5 (0.20)
Unit: mm (in)
S-NT046
PBIC1650E
S-NT014
NT379
NT011
S-NT603
Revision: August 2015
2016 Versa Note

cardiagn.com

EM-8
< PREPARATION >[HR16DE]
PREPARATION
Spark plug wrench
Removing and installing spark plug
a: 14 mm (0.55 in)
Pulley holder Crankshaft pulley removing and installing
Valve seat cutter set Finishing valve seat dimensions
Piston ring expander Removing and installing piston ring
Valve guide drift Removing and installing valve guide
Valve guide reamer (1): Reaming valve guide inner hole
(2): Reaming hole for oversize valve guide
(J-43897-18)
(J-43897-12)
Oxygen sensor thread cleaner Reconditioning the exhaust system threads
before installing a new air fuel ratio sensor
(Use with anti-seize lubricant shown below.)
A: [18 mm (0.71 in) dia.] for zirconia heated
oxygen sensor
B: [12 mm (0.47 in) dia.] for titania heated
oxygen sensor
C: Mating surface shave cylinder
D: Flutes
Tool name
Description
JPBIA0399ZZ
NT035
S-NT048
S-NT030
PBIC4012E
PBIC4013E
JPBIA0238ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

EXHAUST MANIFOLDEM-31
< REMOVAL AND INSTALLATION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EM
NP
O
EXHAUST MANIFOLD
Exploded ViewINFOID:0000000012431707
Removal and InstallationINFOID:0000000012431708
REMOVAL
1. Remove air duct (inlet), air duct and air cleaner assembly. Refer to
EM-26, "Exploded View".
2. Remove exhaust front tube. Refer to EX-5, "
Exploded View".
3. Remove harness bracket from the cylinder head on the right rear side.
4. Remove exhaust manifold upper and lower covers.
5. Disconnect air fuel ratio sensor 1 harness connector.
AWBIA1603ZZ
1. Exhaust manifold cover (upper) 2. Harness bracket 3. Air-fuel ratio sensor 1
4. Exhaust manifold stay 5. Heat insulator6. Exhaust manifold
7. Exhaust manifold cover (lower) 8. Exhaust maifold gasket Engine front
Revision: August 2015 2016 Versa Note

cardiagn.com

FUEL INJECTOR AND FUEL TUBEEM-41
< REMOVAL AND INSTALLATION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EM
NP
O
3. Disconnect fuel feed hose from
fuel tube. Disconnect quick con-
nector:
NOTE:
There is no fuel return path.
a. Remove quick connector cap (engine side) (1) from quick con- nector connection.
b. Disconnect fuel feed hose from hose clamp.
c. With the sleeve (B) side of quick connector release (A) facing quick connector (2), install quick connector release (A) onto fuel
tube (1) as shown.
d. Insert quick connector release (A) into quick connector (2) until sleeve (B) contacts and goes no further. Hold quick connector
release (A) in that position (D).
CAUTION:
Inserting quick connector re lease hard will not disconnect
quick connector. Hold qui ck connector release where it
contacts and goes no further.
e. Draw and pull out quick connector (E) straight up from fuel tube (1).
CAUTION:
• Pull quick connector up (E) from holding position (C) as shown.
• Do not pull with lateral force applied. O-ring inside quick connector may be damaged.
• Prepare container and cloth be forehand as fuel will leak out.
• Discard O-ring, do not reuse.
• Avoid fire and sparks.
• Keep parts away from heat source. Be especi ally careful when welding is performed.
• Do not expose parts to battery electrolyte or other acids.
• Do not bend or twist connection between quick connector and fuel feed tube during installation
or removal.
• Be sure to cover openings of disconnected fuel feed hose
(A) and fuel tube (C) with plug or plastic bag (B) to avoid
fuel leaks and entry of foreign material.
4. Disconnect fuel feed hose from fuel pipe as follows:
(1) : Quick connector cap (engine side)
JPBIA4130ZZ
JPBIA4131ZZ
JPBIA2255ZZ
JSBIA1295ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

EM-42
< REMOVAL AND INSTALLATION >[HR16DE]
FUEL INJECTOR AND FUEL TUBE
NOTE:
There is no fuel return path.
a. Remove quick connector cap (floor piping side) (1) from quick connector connection.
b. Disconnect fuel feed hose from hose clamp (1).
c. Hold the quick connector (1) wh ile pushing in tabs (F), and pull
out the hard tube (A).
CAUTION:
• Inserting quick connector re lease hard will not disconnect
quick connector. Hold qui ck connector release where it
contacts and goes no further.
• The tube can be removed when the tabs are completely depressed. Do not twist it more than necessary.
• Do not use any tools to remove the quick connector.
• Keep the resin tube away from heat. Be especially careful
when welding near the tube.
• Prevent acid such as battery electrolyte etc. from getting on the resin tube.
• Do not bend or twist the tube during installation and removal.
• Remove the remaining retainer only when the tube is replaced.
• When the tube is replaced, also replace the retainer.
JSBIA1291ZZ
JSBIA1292ZZ
(2) : Retainer
(B) : Connection (cross-section)
(C) : Resin tube
(D) : To under floor fuel line
(E) : To fuel tank
(G) : Disconnection
JPBIA0130ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

CYLINDER HEADEM-81
< REMOVAL AND INSTALLATION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EM
NP
O
2. At each of several locations on bottom surface of cylinder head,
measure the distortion in six directions using suitable tools (A/
B).
• If it exceeds the limit, replace cylinder head.
INSPECTION AFTER DISASSEMBLY
VALVE DIMENSIONS
• Check the dimensions of each valv e. For the dimensions, refer to EM-119, "Cylinder head".
• If dimensions are out of the standard, replace valv e and check valve seat contact. Refer to “VALVE SEAT
CONTACT”.
VALVE GUIDE CLEARANCE
Valve Stem Diameter• Measure the diameter of valve stem using suitable tool (A).
Valve Guide Inner Diameter• Measure the inner diameter of valve guide using suitable tool (A).
Valve Guide Clearance• (Valve guide clearance) = (Valve guide inner diameter) – (Valve stem diameter)
• If the calculated value exceeds the limit, replace valve and/or valve guide. Refer to EM-78, "
Disassembly
and Assembly".
VALVE GUIDE REPLACEMENT
When valve guide is removed, replace with oversized [0.2 mm (0.008 in)] valve guide.
1. To remove valve guide, heat cylinder head to 110 to 130°C (230
to 266 °F) by soaking in heated oil.
Limit : Refer to
EM-119, "
Cylinder head".
PBIC3207J
Standard : Refer to EM-119, "Cylinder head".
Standard : Refer to EM-119, "
Cylinder head".
Standard and Limit : Refer to EM-119, "
Cylinder head".
PBIC3213J
SEM008A
Revision: August 2015 2016 Versa Note

cardiagn.com

EM-82
< REMOVAL AND INSTALLATION >[HR16DE]
CYLINDER HEAD
2. Drive out valve guide with a press [under a 20 kN (2 ton, 2.2 US
ton, 2.0 lmp ton) force] or suitable tool.
WARNING:
Cylinder head contains heat; when working, wear protective
equipment to avoid getting burned.
3. Ream cylinder head valve guide hole with a suitable tool.
4. Heat cylinder head to 110 to 130 °C (230 to 266 °F) by soaking in
heated oil.
5. Using a suitable tool, press valve guide (1) from camshaft side of cylinder head (2) to dimensions as shown.
WARNING:
Cylinder head contains heat; when working, wear protective
equipment to avoid getting burned.
6. Apply reamer finish to valve guide with a suitable tool.
SEM931C
Valve guide hole diameter (for service parts): Intake and exhaust: 9.175 - 9.201 mm (0.3612 - 0.3622 in)
SEM932C
SEM008A
Projection “H” : 11.4 - 11.8 mm (0.448 - 0.464 in)
PBIC3217J
Standard : 5.000 - 5.018 mm (0.1968 - 0.1975 in)
SEM932C
Revision: August 2015 2016 Versa Note

cardiagn.com

CYLINDER HEADEM-83
< REMOVAL AND INSTALLATION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EM
NP
O
VALVE SEAT CONTACT
• After confirming that the dimensions of valve guides
and valves are within the specifications, perform this
procedure.
• Apply prussian blue (or white lead) onto contacting surfac e of valve seat to check the condition of the valve
contact on the surface.
• Check if the contact area band is continuous all around the circum- ference.
• If not, grind to adjust valve fitting and check again. If the contacting surface still has “NG” conditions (B) even after the recheck,
replace valve seat. Refer to EM-78, "
Disassembly and Assembly".
VALVE SEAT REPLACEMENT
When valve seat is removed, replace with oversized [0.5 mm (0.020 in)] valve seat.
1. Bore out old seat until it collapses. Boring shoul d not continue beyond the bottom face of the seat recess
in cylinder head. Set the machine depth stop to ensure this.
CAUTION:
Prevent scoring cylinder head by excessive boring.
2. Ream cylinder head recess diameter for service valve seat.
• Be sure to ream in circles concentric to the valve guide center.This will enable valve seat to fit correctly.
3. Heat cylinder head to 110 to 130 °C (230 to 266 °F) by soaking in
heated oil.
4. Provide valve seats cooled well with dry ice. Press-fit valve seats into cylinder head. WARNING:
Cylinder head contains heat; when working, wear protective equipment to avoid getting burned.
CAUTION:
Avoid directly touching cold valve seats.
(A) : OK
JPBIA0187ZZ
Oversize [0.5 mm (0.020 in)]
Intake : 32.500 - 32.527 mm (1.2795 - 1.2805 in)
Exhaust : 26.400 - 26.427 mm (1.0393 - 1.0404 in)
SEM795A
SEM008A
Revision: August 2015 2016 Versa Note

cardiagn.com