2016 NISSAN NOTE lock

DLK-166
< REMOVAL AND INSTALLATION >[WITH INTELLIGENT KEY SYSTEM]
HOOD LOCK
• After installation, perform hood assembl
y adjustment procedure. Refer to DLK-141, "HOOD ASSEM-
BLY : Adjustment".
• After adjustment, perform hood lock control inspection. Refer to DLK-166, "
HOOD LOCK : Inspec-
tion".
HOOD LOCK : InspectionINFOID:0000000012430120
HOOD LOCK INSPECTION
NOTE:
If hood lock cable is bent or deformed, replace it. Refer to DLK-165, "
HOOD LOCK : Removal and Installa-
tion".
1. Check that secondary latch is properly engage with secondary striker with hoods own weight.
2. While operating hood lock release lever, carefully check that the front end of hood assembly is raised by approximately 20.0 mm (0.79 in). Also check that hood lock release lever returns to original position.
3. Check that hood lock release lever operates at 49 N (5.0 kg-m, 11.0 ft-lb) or below.
4. Install so that static closing force of hood is 315-490 N (32.1-50.0 kg-m, 70.8-110.2 ft-lb).
5. Check hood lock assembly lubrication condition. If necessary, apply a suitable multi-purpose grease.
HOOD LOCK RELEASE CABLE
HOOD LOCK RELEASE CABLE : Removal and InstallationINFOID:0000000012430121
REMOVAL
1. Disconnect hood lock release cable from hood lock. Refer to DLK-165, "Exploded View".
2. Remove radiator cap adapter bracket bolt (A) and radiator reser- voir tank bolt (B).
3. Remove fender protector (LH). Refer to EXT-38, "
Removal and Installation".
4. Release hood lock control cable clips using a suitable tool.
5. Remove hood lock/fuel filler door release handle. Refer to DLK-167, "
HOOD LOCK RELEASE HANDLE :
Removal and Installation".
6. Remove dash side finisher (LH). Refer to INT-24, "
DASH SIDE FINISHER : Removal and Installation".
7. Remove grommet on the lower dash and pull the hood lock release cable into the passenger compart- ment.
CAUTION:
While pulling, be careful no t to damage (peel) the outsid e of the hood lock release cable.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Be careful not to bend cable too much, keep the radius 100 mm (3.94 in) or more.
• Check that hood lock release cable is properly engaged with hood lock.
JMKIA8027ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

HOOD LOCKDLK-167
< REMOVAL AND INSTALLATION > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
• Check that cable is not offset from the positioning grommet, and apply the sealant to the grommet (at * mark).
HOOD LOCK RELEASE HANDLE
HOOD LOCK RELEASE HANDLE : Removal and InstallationINFOID:0000000012430122
REMOVAL
1. Remove hood lock/fuel filler door release handle bolts (A).
2. Disconnect hood lock release cable from hood lock/fuel filler door release handle and remove.
INSTALLATION
Installation is in the reverse order of removal.
PIIB5801E
AWKIA2498ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-168
< REMOVAL AND INSTALLATION >[WITH INTELLIGENT KEY SYSTEM]
FRONT DOOR LOCK
FRONT DOOR LOCK
Exploded ViewINFOID:0000000012430123
DOOR LOCK
DOOR LOCK : Removal and InstallationINFOID:0000000012430124
REMOVAL
1. Remove inside handle. Refer to
DLK-169, "INSIDE HANDLE : Removal and Installation".
2. Remove outside handle. Refer to DLK-170, "
OUTSIDE HANDLE : Removal and Installation".
3. Disconnect the harness connector from the door lock actuator.
4. Remove front door glass rear run. Refer to GW-21, "
Exploded View".
5. Remove bolts and door lock.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse door lock bolts.
• After installation, check door op en/close, lock/unlock operation.
• Check door lock cables are properly engaged to inside handle and outside handle bracket.
• When installing key cylinder on front door, be sure to rotate key cylinder r od holder until a click is
felt.
1. Key cylinder (driver side) 2. Outside handle bracket 3. Outside handle escutcheon
(passenger side)
4. Front gasket 5. Outside handle 6. Inside handle
7. Door lock 8. Key cylinder rod (driver side) 9. Rear gasket
A. Clip B. Bolt Pawl
AWKIA3159ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

FRONT DOOR LOCKDLK-169
< REMOVAL AND INSTALLATION > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
• Check door lock for poor lubri cation. Apply a suitable multi-
purpose grease to door lock if necessary.
INSIDE HANDLE
INSIDE HANDLE : Removal and InstallationINFOID:0000000012430125
REMOVAL
1. Remove front door finisher. Refer to INT-15, "Removal and Installation".
2. Partially remove vapor barrier. Refer to GW-21, "
Exploded View".
3. Release lock knob (2) and inside handle cable (3) from clip (1) using a suitable tool.
4. Remove inside handle bolt.
5. Release inside handle (1) from door panel using a suitable tool and remove.
: Pawl
6. Release inside handle cable (3) and lock cable (2) from inside handle (1) and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
JMKIA8077ZZ
JMKIA8078ZZ
AWKIA2500ZZ
JMKIA5885ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-170
< REMOVAL AND INSTALLATION >[WITH INTELLIGENT KEY SYSTEM]
FRONT DOOR LOCK
• Check that door lock cables are properly engaged to inside handle.
• After installation, check door
open/close, lock/unlock operation.
OUTSIDE HANDLE
OUTSIDE HANDLE : Removal and InstallationINFOID:0000000012430126
REMOVAL
1. Remove front door finisher. Refer to INT-15, "Removal and Installation".
2. Partially remove vapor barrier. Refer to GW-21, "
Exploded View".
3. Open rod holder (1) by pulling downward and separate key rod (3) from door lock assembly (2) (driver side only).
4. Release outside handle cable (1) from cable clip (A).
5. Remove door grommet (1) and bolt from grommet hole (2).
6. While pulling outside handle, remove outside handle escutch- eon.
JMKIA8080ZZ
AWKIA2574ZZ
JMKIA5888ZZ
JMKIA0560ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

FRONT DOOR LOCKDLK-171
< REMOVAL AND INSTALLATION > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
7. While pulling outside handle (1), slide toward rear of vehicle.
8. Disconnect the harness connectors from the outside handle and remove.
9. Remove front gasket and rear gasket.
10. Slide outside handle bracket toward rear of vehicle to remove. : Front
11. Disconnect outside handle cable (1) from outside handle bracket (2) as shown.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Check that door lock cables are properly engaged with outside handle bracket.
• After installation, check door op en/close, and lock/unlock operation.
JMKIA0524ZZ
JMKIA5890ZZ
JMKIA5891ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-172
< REMOVAL AND INSTALLATION >[WITH INTELLIGENT KEY SYSTEM]
REAR DOOR LOCK
REAR DOOR LOCK
Exploded ViewINFOID:0000000012430127
DOOR LOCK
DOOR LOCK : Removal and InstallationINFOID:0000000012430128
REMOVAL
1. Remove inside handle. Refer to
DLK-173, "INSIDE HANDLE : Removal and Installation".
2. Remove outside handle. Refer to DLK-174, "
OUTSIDE HANDLE : Removal and Installation".
3. Remove bolts (A) from rear door glass rear run (1).
4. Disconnect the harness connector from door lock actuator.
5. Remove bolts and door lock.
1. Outside handle bracket 2. Outside handle escutcheon 3. Front gasket
4. Outside handle 5. Inside handle6. Door lock
7. Door lock A. Clip B. Bolt
Pawl
AWKIA3160ZZ
JMKIA8086ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

REAR DOOR LOCKDLK-173
< REMOVAL AND INSTALLATION > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse door lock assembly bolts.
• After installation, check door open/close, lock/un lock operation.
• Check door lock cable is properly engaged wi th inside handle and outside handle bracket.
• Check door lock assembly for poor lubrication. If necessary, apply a suitable multi-purpose grease.
INSIDE HANDLE
INSIDE HANDLE : Removal and InstallationINFOID:0000000012430129
REMOVAL
1. Remove rear door finisher. Refer to INT-18, "Removal and Installation".
2. Remove upper portion of vapor barrier. Refer to GW-25, "
Exploded View".
3. Release lock knob (2) and inside handle cable (3) from clip (1) using a suitable tool.
4. Remove inside handle bolt.
5. Release inside handle (1) from door panel using a suitable tool and remove.
: Pawl
JMKIA8087ZZ
JMKIA5704ZZ
AWKIA2500ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com