2016 NISSAN NOTE air conditioning

BRC-84
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
C1116 STOP LAMP SWITCH
C1116 STOP LAMP SWITCH
DTC DescriptionINFOID:0000000012430866
DTC DETECTION LOGIC
POSSIBLE CAUSE
NOTE:
Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear
the DTC. Do not replace the
ABS actuator and electric unit (control unit) for a PAST DTC.
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
With CONSULT
1. Turn the ignition switch OFF, and wait 10 seconds or more.
2. Start the engine.
NOTE:
Stop the vehicle.
3. Wait 1 minute or more. NOTE:
Never depress brake pedal.
4. Depress brake pedal by 100 mm (3.94 in) or more, and ma intain at that position for a minimum of 1 minute
or more.
5. Release brake pedal, and wait 1 minute or more.
6. Repeat step 4 to 5 ten or more times.
7. Turn the ignition switch OFF. NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
8. Start the engine. NOTE:
Wait at least 10 seconds after starting the engine.
9. Perform “Self Diagnostic Result” of “ABS”.
Is DTC
“C1116” detected?
YES-1 >> “C1116” is displayed as “CRNT”: Proceed to BRC-85, "Diagnosis Procedure".
YES-2 >> “C1116” is displayed as “PAST”: Inspection End (Erase “Self Diagnos tic Result” of “ABS”).
NO-1 >> To check malfunction symptom before repair: Refer to GI-42, "
Intermittent Incident".
NO-2 >> Confirmation after repair: Inspection End.
DTC Display Item
(Trouble diagnosis content) Malfunction detected condition
C 111 6 STOP LAMP SW
(Stop lamp switch) • When stop lamp switch signal is not input when brake pedal operates.
• When stop lamp switch signal is input when brake pedal is not operated.
PAST DTC
CRNT DTC
• Harness or connector
• Stop lamp switch signal circuit • Harness or connector
• Stop lamp switch
• ABS actuator and electric unit (control unit)
• ABS actuator and electric unit
(control unit) power supply sys-
tem
•Fuse
• Fusible link
•Battery
Revision: August 2015 2016 Versa Note

cardiagn.com

BRC-88
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
C1120, C1122, C1124, C112
6 ABS IN VALVE SYSTEM
C1120, C1122, C1124, C1126 ABS IN VALVE SYSTEM
DTC DescriptionINFOID:0000000012430869
DTC DETECTION LOGIC
POSSIBLE CAUSE
NOTE:
Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear
the DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC.
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
With CONSULT
1. Turn the ignition switch OFF. NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
2. Start the engine. NOTE:
Wait at least 10 seconds after starting the engine.
3. Perform “Self Diagnostic Result” of “ABS”.
Is DTC
“C1120”, “C1122”, “C1124” or “C1126” detected?
YES-1 >> “C1120”, “C1122”, “C1124” or “C1126” is displayed as “CRNT”: Proceed to BRC-88, "Diagnosis
Procedure".
YES-2 >> “C1120”, “C1122”, “C1124” or “C1126” is disp layed as “PAST”: Inspection End (Erase “Self Diag-
nostic Result” of “ABS”).
NO-1 >> To check malfunction symptom before repair: Refer to GI-42, "
Intermittent Incident".
NO-2 >> Confirmation after repair: Inspection End.
Diagnosis ProcedureINFOID:0000000012430870
1.CHECK CONNECTOR
DTC Display Item
(Trouble diagnosis content) Malfunction detected condition
C1120 FR LH IN ABS SOL
(Front LH ABS IN solenoid valve) When a malfunction is detected in front LH ABS IN valve.
C1122 FR RH IN ABS SOL
(Front RH ABS IN solenoid valve) When a malfunction is detected in front RH ABS IN valve.
C1124 RR LH IN ABS SOL
(Rear LH ABS IN solenoid valve) When a malfunction is detected in rear LH ABS IN valve.
C1126 RR RH IN ABS SOL
(Rear RH ABS IN so
lenoid valve)When a malfunction is detected in rear RH ABS IN valve.
PAST DTC
CRNT DTC
• Harness or connector
• ABS actuator and electric unit (control unit) power supply sys-
tem
•Fuse
• Fusible link
•Battery • Harness or connector
• ABS actuator and electric unit (control unit)
• ABS actuator and electric unit
(control unit) power supply sys-
tem
•Fuse
• Fusible link
•Battery
Revision: August 2015 2016 Versa Note

cardiagn.com

BRC-90
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
C1121, C1123, C
1125, C1127 ABS OUT VALVE SYSTEM
C1121, C1123, C1125, C1127 ABS OUT VALVE SYSTEM
DTC DescriptionINFOID:0000000012430871
DTC DETECTION LOGIC
POSSIBLE CAUSE
NOTE:
Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear
the DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC.
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
With CONSULT
1. Turn the ignition switch OFF. NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
2. Start the engine. NOTE:
Wait at least 10 seconds after starting the engine.
3. Perform “Self Diagnostic Result” of “ABS”.
Is DTC
“C1121”, “C1123”, “C1125” or “C1127” detected?
YES-1 >> “C1121”, “C1123”, “C1125” or “C1127” is displayed as “CRNT”: Proceed to BRC-90, "Diagnosis
Procedure".
YES-2 >> “C1121”, “C1123”, “C1125” or “C1127” is disp layed as “PAST”: Inspection End (Erase “Self Diag-
nostic Result” of “ABS”).
NO-1 >> To check malfunction symptom before repair: Refer to GI-42, "
Intermittent Incident".
NO-2 >> Confirmation after repair: Inspection End.
Diagnosis ProcedureINFOID:0000000012430872
1.CHECK CONNECTOR
DTC Display Item
(Trouble diagnosis content) Malfunction detected condition
C1121 FR LH OUT ABS SOL
(Front LH ABS OUT solenoid valve) When a malfunction
is detected in front LH ABS OUT valve.
C1123 FR RH OUT ABS SOL
(Front RH ABS OUT solenoid valve) When a malfunction is detected in front RH ABS OUT valve.
C1125 RR LH OUT ABS SOL
(Rear LH ABS OUT solenoid valve) When a malfunction is detected in rear LH ABS OUT valve.
C1127 RR RH OUT ABS SOL
(Rear RH ABS OUT so
lenoid valve)When a malfunction
is detected in rear RH ABS OUT valve.
PAST DTC CRNT DTC
• Harness or connector
• ABS actuator and electric unit (control unit) power supply sys-
tem
•Fuse
• Fusible link
•Battery • Harness or connector
• ABS actuator and electric unit (control unit)
• ABS actuator and electric unit
(control unit) power supply sys-
tem
•Fuse
• Fusible link
•Battery
Revision: August 2015 2016 Versa Note

cardiagn.com

BRC-92
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
C1130 ENGINE SIGNAL
C1130 ENGINE SIGNAL
DTC DescriptionINFOID:0000000012430873
DTC DETECTION LOGIC
POSSIBLE CAUSE
NOTE:
Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear
the DTC. Do not replace the
ABS actuator and electric unit (control unit) for a PAST DTC.
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
With CONSULT
1. Turn the ignition switch OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
2. Start the engine.
NOTE:
Wait at least 10 seconds after starting the engine.
3. Perform “Self Diagnostic Result” of “ABS”.
Is DTC
“C1130” detected?
YES-1 >> “C1130” is displayed as “CRNT”: Proceed to BRC-92, "Diagnosis Procedure".
YES-2 >> “C1130” is displayed as “PAST”: Inspection End (Erase “Self Diagnostic Result” of “ABS”).
NO-1 >> To check malfunction symptom before repair: Refer to GI-42, "
Intermittent Incident".
NO-2 >> Confirmation after repair: Inspection End.
Diagnosis ProcedureINFOID:0000000012430874
1.CHECK ENGINE SYSTEM
With CONSULT
Perform “Self Diagnostic Result” of “ENGINE”.
Is DTC detected?
YES >> Check the DTC. Refer to EC-87, "DTCIndex".
NO >> GO TO 2.
DTC Display Item
(Trouble diagnosis content) Malfunction detected condition
C1130 ENGINE SIGNAL 1
(Engine system signal) When a malfunction is detected in ECM system.
PAST DTC
CRNT DTC
• Harness or connector
• ABS actuator and electric unit (control unit) power supply sys-
tem
•Fuse
• Fusible link
•Battery
• CAN communication line • Harness or connector
•ECM
• ABS actuator and electric unit (control unit)
• ABS actuator and electric unit
(control unit) power supply sys-
tem
•Fuse
• Fusible link
•Battery
• CAN communication line
Revision: August 2015 2016 Versa Note

cardiagn.com

BRC-94
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
C1140 ACTUATOR RELAY SYSTEM
C1140 ACTUATOR RELAY SYSTEM
DTC DescriptionINFOID:0000000012430875
DTC DETECTION LOGIC
POSSIBLE CAUSE
NOTE:
Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear
the DTC. Do not replace the
ABS actuator and electric unit (control unit) for a PAST DTC.
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
With CONSULT
1. Turn the ignition switch OFF. NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
2. Start the engine. NOTE:
Wait at least 10 seconds after starting the engine.
3. Perform “Self Diagnostic Result” of “ABS”.
Is DTC
“C1140” detected?
YES-1 >> “C1140” is displayed as “CRNT”: Proceed to BRC-94, "Diagnosis Procedure".
YES-2 >> “C1140” is displayed as “PAST”: Inspection End (Erase “Self Diagnostic Result” of “ABS”).
NO-1 >> To check malfunction symptom before repair: Refer to GI-42, "
Intermittent Incident".
NO-2 >> Confirmation after repair: Inspection End.
Diagnosis ProcedureINFOID:0000000012430876
1.CHECK CONNECTOR
1. Turn the ignition switch OFF.
2. Check the ABS actuator and electric unit (contro l unit) harness connector for disconnection or looseness.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair / replace harness or connector, securely lock the connector, and GO TO 2.
2.PERFORM SELF-DIAGNOSIS
DTC Display Item
(Trouble diagnosis content) Malfunction detected condition
C1140 ACTUATOR RLY
(Actuator relay) When a malfunction is detected in actuator relay.
PAST DTC
CRNT DTC
• Harness or connector
• ABS actuator and electric unit (control unit) power supply sys-
tem
•Fuse
• Fusible link
•Battery • Harness or connector
• ABS actuator and electric unit (control unit)
• ABS actuator and electric unit
(control unit) power supply sys-
tem
•Fuse
• Fusible link
•Battery
Revision: August 2015 2016 Versa Note

cardiagn.com

BRC-96
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
C1142 PRESS SENSOR
C1142 PRESS SENSOR
DTC DescriptionINFOID:0000000012430877
DTC DETECTION LOGIC
POSSIBLE CAUSE
NOTE:
Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear
the DTC. Do not replace the
ABS actuator and electric unit (control unit) for a PAST DTC.
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
With CONSULT
1. Turn the ignition switch OFF. NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
2. Start the engine. NOTE:
Wait at least 10 seconds after starting the engine.
3. Perform “Self Diagnostic Result” of “ABS”.
Is DTC
“C1142” detected?
YES-1 >> “C1142” is displayed as “CRNT”: Proceed to BRC-96, "Diagnosis Procedure".
YES-2 >> “C1142” is displayed as “PAST”: Inspection End (Erase “Self Diagnostic Result” of “ABS”).
NO-1 >> To check malfunction symptom before repair: Refer to GI-42, "
Intermittent Incident".
NO-2 >> Confirmation after repair: Inspection End.
Diagnosis ProcedureINFOID:0000000012430878
1.STOP LAMP SWITCH SYSTEM
Check the stop lamp switch system. Refer to BRC-85, "
Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace stop lamp switch system.
2.CHECK BRAKE FLUID LEAKAGE
DTC Display Item
(Trouble diagnosis content) Malfunction detected condition
C1142 PRESS SEN CIRCUIT
(Pressure sensor circuit) When a malfunction is detected in pressure sensor.
PAST DTC
CRNT DTC
• Harness or connector
• Air inclusion in the brake piping
• Stop lamp switch system
• ABS actuator and electric unit (control unit) power supply sys-
tem
•Fuse
• Fusible link
•Battery • Stop lamp switch system
• ABS actuator and electric unit (control unit)
• Brake system
• ABS actuator and electric unit
(control unit) power supply sys-
tem
•Fuse
• Fusible link
•Battery
• Air inclusion in the brake piping
Revision: August 2015 2016 Versa Note

cardiagn.com

C1143 STEERING ANGLE SENSORBRC-99
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
C1143 STEERING ANGLE SENSOR
DTC DescriptionINFOID:0000000012430879
DTC DETECTION LOGIC
POSSIBLE CAUSE
NOTE:
Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear
the DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC.
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
With CONSULT
1. Turn the ignition switch OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
2. Start the engine.
NOTE:
Wait at least 10 seconds after starting the engine.
3. Perform “Self Diagnostic Result” of “ABS”.
Is DTC
“C1143” detected?
YES-1 >> “C1143” is displayed as “CRNT”: Proceed to BRC-99, "Diagnosis Procedure".
YES-2 >> “C1143” is displayed as “PAST”: Inspecti on End (Erase “Self Diagnostic Result” of “ABS”).
NO-1 >> To check malfunction symptom before repair: Refer to GI-42, "
Intermittent Incident".
NO-2 >> Confirmation after repair: Inspection End.
Diagnosis ProcedureINFOID:0000000012430880
1.ADJUST THE NEUTRAL POSITION OF STEERING ANGLE SENSOR
With CONSULT
Perform neutral position adjustment of steering angle sensor. Refer to BRC-55, "
ADJUSTMENT OF STEER-
ING ANGLE SENSOR NEUTRAL POSITION : Description".
DTCDisplay Item
(Trouble diagnosis content) Malfunction detected condition
C1143 ST ANG SEN CIRCUIT
(Steering angle sensor circuit) When a malfunction is detected in steering angle sensor.
PAST DTC
CRNT DTC
• Harness or connector
• ABS actuator and electric unit (control unit) power supply sys-
tem
•Fuse
• Fusible link
•Battery
• CAN communication line
• Incomplete neutral position adjustment of steering angle sensor
• Improper installation of steering angle sensor • Harness or connector
• Steering angle sensor
• ABS actuator and electric unit (control unit)
• IPDM E/R
• CAN communication line
• Wheel alignment
• Incomplete neutral position adjustment of steering angle sensor
• ABS actuator and electric unit
(control unit) power supply sys-
tem
•Fuse
• Fusible link
•Battery
Revision: August 2015 2016 Versa Note

cardiagn.com

C1144 INCOMPLETE STEERING ANGLE SENSOR ADJUSTMENT
BRC-103
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
C1144 INCOMPLETE STEERING ANGLE SENSOR ADJUSTMENT
DTC DescriptionINFOID:0000000012430881
DTC DETECTION LOGIC
POSSIBLE CAUSE
NOTE:
Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear
the DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC.
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
With CONSULT
1. Turn the ignition switch OFF. NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
2. Start the engine. NOTE:
Wait at least 10 seconds after starting the engine.
3. Perform “Self Diagnostic Result” of “ABS”.
Is DTC
“C1144” detected?
YES-1 >> “C1144” is displayed as “CRNT”: Proceed to BRC-103, "Diagnosis Procedure".
YES-2 >> “C1144” is displayed as “PAST”: Inspecti on End (Erase “Self Diagnostic Result” of “ABS”).
NO-1 >> To check malfunction symptom before repair: Refer to GI-42, "
Intermittent Incident".
NO-2 >> Confirmation after repair: Inspection End.
Diagnosis ProcedureINFOID:0000000012430882
1.ADJUST THE NEUTRAL POSITION OF STEERING ANGLE SENSOR
Perform neutral position adjustment of steering angle sensor. Refer to BRC-55, "
ADJUSTMENT OF STEER-
ING ANGLE SENSOR NEUTRAL POSITION : Description".
>> GO TO 2.
2.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
With CONSULT
1. Turn the ignition switch OFF.
NOTE:
DTC Display Item
(Trouble diagnosis content) Malfunction detected condition
C1144 ST ANG SEN SIGNAL
(Steering angle sensor not com-
plete) When neutral position adjustment of steering angle sensor is not complete.
PAST DTC
CRNT DTC
Incomplete neutral position adjustment of steering angle sensor • Harness or connector • Steering angle sensor
• ABS actuator and electric unit (control unit)
• Incomplete neutral position adjustment of steering angle sensor
Revision: August 2015 2016 Versa Note

cardiagn.com