2016 MITSUBISHI LANCER Owners Manual

Free-hand Advanced Security Transmit
ter (F.A.S.T.-key) (if so equipped)
Features and controls
5-27
5
After
several
attempts,
you
may
experience
that the engine still does not start.1.Make
sure
that
all
electric
devices,
such
as
lights,
air
conditioning
blower
and
rear
window defogger
, are turned of
f.
2.While
depressing
the
brake
pedal
on
vehi-
cles
equipped
with
continuously
variable
transmission
(CVT)
or the
clutch
pedal
on
the
vehicles
equipped
with
manual
trans-
axle,
press
the
accelerator
pedal
halfway
and
hold
it there,
then
crank
the
engine.
Release
the
accelerator
pedal,
immedi-
ately after the engine starts.3.If the
engine
still
will
not
start,
the
engine
could
be
flooded
with
too
much
gasoline.
While
depressing
the
brake
pedal
on
vehi-
cles
equipped
with
CVT
or
the
clutch
pedal
on
the
vehicles
equipped
with
man-
ual
transaxle,
push
the
accelerator
pedal
all the
way
down
and
hold
it there,
then
crank
the
engine
for
5
to
6
seconds.
Return
the
ignition
switch
to the
“LOCK”
position
and
release
the
accelerator
pedal.
Wait
a few
seconds,
and
then
crank
the
engine
again
for
5 to
6 seconds
while
depressing
the
brake
pedal
or
the
clutch
pedal,
but
do
not
push
the
accelerator
pedal.
Release
the
ignition
key
if
the
engine
starts.
If the
engine
fails
to
start,
repeat
these
procedures.
If the
engine
still
will
not
start,
contact
your
local
Mitsubi-
shi
Motors
dealer
or
a repair
facility
of
your choice for assistance.
When
the
ambient
temperature
is
-4°F
(-20
°C)
or
lower
, it may
not
be
possible
to
start
from
a standstill
even
with
the
selector
lever
in
the
“D”
(DRIVE)
or
“R”
(REVERSE) position. This
phenomenon
occurs
because
the
trans-
axle has
not warmed
up sufficiently
; it does
not
indicate
a problem.
If this
occurs,
place
the
selector
lever
in the
“P”
(PARK)
position
and let the engine idle for at least 10
minutes.
The
transaxle
will
warm
up,
and
you
will
be
able to drive normally
.
Do
not
leave
the
vehicle
during
warm-up
operation.
N00529600
101
The
electronic
immobilizer
is designed
to sig-
nificantly
reduce
the
possibility
of
vehicle
theft.
The
purpose
of
the
system
is to immo-
bilize
the
vehicle
if
an
invalid
start
is
attempted.
A valid
start
attempt
can
only
be
achieved
(subject
to certain
conditions)
using
a F.A.S.T
.-Key
“registered”
to
the
immobi-
lizer system.
W
AR
NING
Mak
e sur
e to
remove
the F.A.S.T.-key
from
the
emergency
key
after
the
engine
is
start
ed.
If not
removed,
the
F.A.S.T
.-key
could
fall
to
the
floor
, which
may
interf
ere with
pedal
operati
on.
Furthermor
e, the
F.A.S.T
.-ke
y coul
d pre-
vent
the
driv
er’s knee
airbag
from
inflat-
ing
normally
or
could
be
propelled
to
cause serious injury if the airbag inflates.NOTE
When
using
the
emer
gency
key
to start
the
engine,
firs
t remove
the
key
from
the
key
holder
. If the
emer
gency
key
is attached
to a
key holder
(key
ring), it may
beco
me
impos-
sible
to insert
the
keyless
operation
key
into
the emer
gency key, and
it may
pre
vent the
engi
ne from
being
started.
When the engine is hard to start
Startability
of
continuously
variable
transmission
(CVT)
vehicles
at extr
emely
cold ambient temperatur
e
Elect
ronic immobilizer (Anti-
theft starting system)

Free-hand Advanced Security Transmitter (F.A.S.T.-key) (if so equipped)5-28
Features and controls
5
All
of
the
keys
provided
with
your
new
vehi-
cle
have
been
programmed
to
the
vehicle
’s
electronics.
N0056100
0039
Only
the
F.A.S.T
.-keys
that
have
been
pro-
grammed
to
the
vehicle
’s electronics
can
be
used to start the vehicle. If you
los
e the
F.A.S.T.-key
, you
can
order
a
F.A.S.T
.-key
from
your
authorized
Mitsubishi
Motors dealer by referring to the key number
.
To prevent
vehicle
theft,
the
ID
codes
for
all
the
F.A.S.T
.-keys
except
the
one
for
the
lost
F.A.S.T
. -key must be programmed again.
Take
your
vehicle
and
all
the
remaining
F.A.S.T
.-keys
to
your
authorized
Mitsubishi
Motors
dealer
to
have
your
ID
codes
pro-
grammed again.
N00561
100030
To add
a F.A.S.T
.-key
, you
must
already
have
two
registered
F.A.S.T
.-keys.
You
need
to
register the ID code to the vehicle.Registering
the
ID
code
can
be
done
by
your
authorized
Mitsubishi
Motors
dealer
. Or
it
can
be
done
by
yourself
(except
for
vehicles
sold in Canada).
For
you
to register
the
ID
code
yourself,
fol-
low
the
“Customer
F.A.S.T
.-key
program-
ming” procedure belo
w.
If you
choose
to
have
your
authorized
Mit-
subishi
Motors
dealer
register
the
ID
code,
take
your
vehicle
and
all remaining
F.A.S.T
.-
keys
to
your
authorized
Mitsubishi
Motors
deale
r.
N0056120
0073
You
can
program
new
F.A.S.T
.-keys
to
the
system
if you
have
two
valid
(already
regis-
tered)
F.A.S.T
.-keys,
blank
(not
registered)
F.A.S.T
.-key
and
emer
gency
key
(specially
cut
for
your
vehicle
at
your
Mitsubishi
Motors dealer). To use
the
new
F.A.S.T
.-key
, it is necessary
to
register
the
key
with
both
the
electronic
immobilizer and keyless entry system.Also
refer
to
“Keyless
entry
system:
Cus-
tomer
F.A.S.T
.-key
programming”
on
page
5-32. For
F.A.S.T
.-key
programming,
follow
the
procedures belo
w.
1.Remove
the
eme
rgency
key
from
the
F.A.S.T
.-key
. Refer
to
“Eme
rgency
key”
on page 5-22.2.While
pushing
the
lock
release
buttons
(A),
remove
the
cover
of
the
ignition
switch.3.Insert
the
emer
gency
key
into
the
ignition
switch.
Replacement
F.A.S.T
.-key

Additional
F.A.S.T
.-key

NOTE
You
are
provided
with
two
F.A.S.T
.-keys,
but
you may register up to four F
.A.S.T
.-keys.
You can
obtain
blank
F.A.S.T
.-ke
ys specially
cut
for
your
vehicle
from
your Mitsubis
hi
Mot
ors
dealer
.
Customer F
.A.S.T
.-key pr
ogram-
ming (Except for vehicles sold in Canada)

Free-hand Advanced Security Transmit
ter (F.A.S.T.-key) (if so equipped)
Features and controls
5-29
5
4.Insert
the
first
valid
F.A.S.T
.-key
into
the
eme
rgency ke
y.
5.Turn
the
emer
gency
key
with
the
F.A.S.T
.-key
to
the
“ON”
position
for
5
seconds
.
6.Turn
the
eme
rgency
key
with
the
F.A.S.T
.-key
to
the
“LOCK”
position.
Within
30
seconds
after
doing
so,
remove
the
F.A.S.T
.-key
from
the
eme
rgency
key
,
insert
the
second
valid
F.A.S.T
.-key
into
the
eme
rgency
key
and
turn
it to the
“ON”
position.
About
10
seconds
later
, the
immobilizer display will start to blink.7.When
the
immobilizer
display
starts
blinking,
turn
the
second
valid
F.A.S.T
.-
key
to
the
“LOCK”
position
and
remove
it. Within
30
seconds
after
doing
so,
insert
a blank
F.A.S.T
.-key
into
the
emer
gency
key
and
turn
it to the
“ON”
position.
Per
-
form
this oper
ation
no
more
than 30 sec-
onds
after
the
immobilizer
display
starts
blinking.
When
registration
of
the
ID
code
is complete,
the
immobilizer
display
will
come
on
for
3 seconds
then
go
off. If
an
error
occurs,
the
immobilizer
display
will go of
f during the procedure.
8.If you
wish
to
register
another
F.A.S.T
.-
key
, repeat the process from step 1.
NOTE
Perform
the ope
ration
whe
n the interrupt
dis-
play
screen
is not
showi
ng.
The interrupt
dis-
play
screen
may
prevent
you
from
seeing
the
immobilizer
display
.
It is not
possi
ble to register a F.A.S.T
.-ke
y if:
•the
immob
ilizer
display
goe
s off during
the
procedure•the
immob
ilizer
display
doe
s not
come
on
within 30
second
s after turning
the
ign
ition
switch
to the “ON”
positio
n with
a blan
k
F.A.S.T.-key
The
procedure
will
be
terminated
automati-
cally
if:
•a period
of
30
seconds
or
longer
elapses
from
the momen
t whe
n the first F.A.S.T
.-
key is turned
to the “LO
CK” position
to the
momen
t whe
n the second
F.A.S.T
.-ke
y is
turne
d to the “ON”
positio
n
•a period
of
30
seconds
or
longer
elapses
from
the moment
whe
n the seco
nd
F.A.S.
T.-key
is turne
d to the “LO
CK” posi
-
tion
to the moment
when
the blan
k
F.A.S.T
.-ke
y is turne
d to the “ON”
positio
n
To use
the
new
remote
control
transmitters,
it
is necessary
to register
the
key
with
both
the
electronic
immobilizer
and
keyless
entry
sys-
tem.Also refer to “Keyless
entry
system:
Cus-
tomer
F.A.S.T
.-ke
y prog
ramming”
on
page
5-32.

Free-hand Advanced Security Transmitter (F.A.S.T.-key) (if so equipped)5-30
Features and controls
5
N0051550
0141
Press
the
remote
control
transmitter
buttons
to
lock
or
unlock
the
doors
and
to
open
the
trunk
lid.
It can
also
help
you
signal
for
attention
by
setting
off the
panic
alarm.
N0054420
0036
Press
the
LOCK
button
(1)
to
lock
all
the
doors. The turn signal lights will also blink once.
N005443
01135
Press
the
UNLOCK
button
(2)
to
unlock
the
driver
’s door
only
. Within
about
2 seconds,
press
the
UNLOCK
button
one
more
time
to
unlock all the doors.The
dome
light
will
turn
on
for
30
seconds.
The turn signal lights will also blink twice.The
front
side-marker
and
parking
lights
will
also turn on for about 30 seconds. Refer to “W
elcome light” on page 5-131.
N0054440
0012
Press
the
trunk
button
(3)
twice
within
about
5 seconds
and
the
trunk
lid
will
be
opened.
The
trunk
lid
must
be
closed
manually
after
it
has
been
opened.
N0054450
1065
Setting
of
the
horn,
turn
signal
lights
and
buzzer
of
the
keyless
entry
system
answer
-
back
function
can
be
changed
as
required.
This
is done
with
the
key
removed
from
the
ignition switch.The
horn
answerback
function
can
be
set
to
the
following
three
conditions.
Each
time
the
horn
answerback
function
is
set,
a chime
will
sound
to tell
you
the
condi-
tion of the answerback function.
Keyless entry system

1-
LOCK (
) button
2-
UNLOCK (
) button
3-
Trunk (
) butto
n
4-
PANIC (
) button
5-
Indicator light
To lock the doors

NOTE
If
you
press
the
LOCK button (1) twice
quickly
, the horn will sound once.
To unlock the doors

NOTE
The
door
unlock
function
can
be
set
so
that
all
doors
unl
ock
whe
n the UNL
OCK butto
n
(2) is pre
ssed once.
Ref
er to “Settin
g of doo
r
unlock function
” on pa
ge 5-3
1.
To open the trunk lid

Answerback
function

NOTE
The answe
rback
function
doe
s not
ope
rate
whe
n the key is in the ignition
switch
or any
door
is opened.
Horn deactivation/r
eactivation
Number
of
chimes
Condition
One chime
The horn will not sound.
Two chimes
The horn w
ill s
ound.
Four chimes
The horn will sound if the LOCK button is pressed twi
ce qui
ckly.

Free-hand Advanced Security Transmit
ter (F.A.S.T.-key) (if so equipped)
Features and controls
5-31
5
1.Turn
the
ignition
switch
to
the
“LOCK”
position.
If you
started
the
engine
with
the
key
, remove
the
key
from
the
ignition
switch.2.Open
the
driver
’s door
and
turn
the
com-
bination
headlights
and
dimmer
switch
to
the “OFF” position.3.Press
the
LOCK
button
(1)
for
4 to 10
sec-
onds
and
press
the
UNLOCK
button
(2)
during this time.4.Release
in
sequence
the
UNLOCK
and
LOCK
buttons
within
10
seconds
of
pressing the UNLOCK button in step 3.
The
turn
signal
lights
answerback
function
can be set to the following seven conditions.Each
time
the
turn
signal
lights
answerback
function
is set,
a chime
will
sound
to tell
you
the condition of the answerback function.
1.Turn
the
ignition
switch
to
the
“LOCK”
position.
If you
started
the
engine
with
the
key
, remove
the
key
from
the
ignition
switch.2.Open
the
driver
’s door
and
turn
the
com-
bination
headlights
and
dimmer
switch
to
the “OFF” position.3.Press
the UNLOCK
button
(2)
for
4 to 10
seconds
and
press
the
LOCK
button
(1)
during this time.4.Release
in
sequence
the
UNLOCK
and
LOCK
buttons
within
10
seconds
of
pressing the LOCK button in step 3.
The
buzzer
answerback
function
can
be
turned ON or OFF as required.
N005446
01112
The
door
unlock
function
can
be
set
to the
following two conditions.
Each
time
the
door
unlock
function
is set,
a
chime
will
sound
to tell you
the
condition
of
the door unlock function.1.Turn
the
ignition
switch
to
the
“LOCK”
position.
If you
started
the
engine
with
the
key
, remove
the
key
from
the
ignition
switch.2.Open
the
driver
’s door
and
turn
the
com-
bination
headlights
and
dimmer
switch
to
the “OFF” position.3.Press
the
LOCK
button
(1)
for
4 to 10
sec-
onds
and
press
the
UNLOCK
button
(2)
during this time.4.Release
in
sequence
the
LOCK
and
UNLO
CK
buttons
within
10
seconds
of
pressing the LOCK button in step 3.
N00544700
015
If you
are
near
your
vehicle
and
feel
threat-
ened,
you
can
activate
the
alarm
to call
atten-
tion as follows:1.Press
the
PANIC
button
(4)
for
more
than
1 s
econd.
Changing
the
setting
of
the
turn
signal
lights answerback functionNumber of chimes
Condition
To lock
To un
lock
One chime
One flash
Two flashes
Two chimes
One flash
No flash
Three chimes
No flash
Two flashes
Four chimes
Two flashes
One flash
Five chime
s
No flash
One flash
Six chime
s
Two flashes
No flash
Seve
n
chimes
No flash
No flash
Buzzer deactivation/r
eactivation
Setting of door unlock function

Number of chimes
Condition
To lock
To un
lock
Number
of
chimes
Condition
One chim
e
All doors unlock
Two chime
s
Driver
’s door unlock only
Using the panic alarm

Free-hand Advanced Security Transmitter (F.A.S.T.-key) (if so equipped)5-32
Features and controls
5
2.The
headlights
will
blink
on
and
off and
the
horn
will
sound
intermittently
for
about
3 minutes.
3.To turn
off the
alarm,
press
any
button
on
the remote control transmitte
r.
N0056130
0029
Only
a F.A.S.T
.-key
, which
has
been
pro-
grammed
into
the
vehicle’
s electronics,
can
lock
and
unlock
all
the
doors,
and
start
the
engine. If you
los
e the
F.A.S.T.-key
, you
can
order
a
F.A.S.T
.-key
from
your
authorized
Mitsubishi
Motors dealer by referring to the key number
.
To prevent
vehicle
theft,
the
ID
codes
for
all
the
F.A.S.T
.-keys
except
the
one
for
the
lost
F.A.S.T
.-key must be programmed again.
Take
your
vehicle
and
all
the
remaining
F.A.S.T
.-keys
to
your
authorized
Mitsubishi
Motors
dealer
to
have
your
ID
codes
pro-
grammed again.
N0056140
0020
To add
a F.A.S.T
.-key
, you
must
already
have
two registered F
.A.S.T
.-keys.
Registering
the
ID
code
can
be
done
by
your
authorized
Mitsubishi
Motors
dealer
. Or
it
can
be
done
by
yourself
(except
for
vehicles
sold
in
Canada).
For
you
to
register
the
ID
code
yourself,
follow
the
“Customer
F.A.S.T
.-key
programming”
procedure
below
.
If you
choose
to
have
your
authorized
Mit-
subishi
Motors
dealer
register
the
ID
code,
take
your
vehicle
and
all remaining
F.A.S.
T.-
keys
to
your
authorized
Mitsubishi
Motors
deale
r.
N00561
501116
You
can
program
new
F.A.S.T
.-keys
to
the
system
if you
have
two
valid
(already
regis-
tered)
F.A.S.T
.-keys,
blank
(not
registered)
F.A.S.T
.-key
and
emer
gency
key
(specially
cut
for
your
vehicle
at
your
Mitsubishi
Motors dealer).To use
the
new
F.A.S.T
.-key
, it is necessary
to
register
the
key
with
both
the
electronic
immobilizer and keyless entry system.Also
refer
to
“Electronic
immobilizer:
Cus-
tomer
F.A.S.T
.-key
programming”
on
page
5-28. For
F.A.S.T
.-key
programming,
follow
the
procedures below
.
1.Remove
the
eme
rgency
key
from
the
F.A.S.T
.-key
. Refer
to
“Eme
rgency
key”
on page 5-22.2.While
pushing
the
lock
release
buttons
(A),
remove
the
cover
of
the
ignition
switch.3.Insert
the
emer
gency
key
into
the
ignition
switch.4.Insert
the
valid
F.A.S.T
.-key
into
the
emer
gency key
.
Replacement
F.A.S.T
.-keys

Additional
F.A.S.T
.-keys

NOTE
You
are
provided
with
two
F.A.S.T
.-keys,
but
you may register up to four F
.A.S.T
.-keys.
Customer F
.A.S.T
.-key pr
ogram-
ming (Except for vehicles sold in Canada)

Free-hand Advanced Security Transmit
ter (F.A.S.T.-key) (if so equipped)
Features and controls
5-33
5
5.Turn
the
emer
gency
key
with
F.A.S.T
.-
key
to
the
“ON”
position.
(Perform
the
following procedure within 30 seconds)6.Remove
the
F.A.S.T
.-key
from
the
emer
-
gency key
.
7.With
the
first
valid
F.A.S.T
.-key
, press
the
UNLOCK
button
for
4 to 10
seconds
and
press the LOCK button during this time.8.Release
in
sequence
the
LOCK
and
UNLO
CK
buttons
within
10
seconds
of
pressing
the
LOCK
button
in step
7. (Per
-
form
the
following
procedure
within
30
seconds
)
9.With
the
second
valid
F.A.S.T
.-key
, press
the
UNLOCK
button
for
4 to 10
seconds
and
press
the
LOCK
button
during
this
time.
10.
Release
in
sequence
the
LOCK
and
UNLO
CK
buttons
within
10
seconds
of
pressing
the LO
CK
butt
on
in
step
9, and
the
immobilizer
display
will
blink
on
the
information
screen
in
the
multi-informa-
tion
display
. (Perform
the
following
pro-
cedure within 60 seconds)
11.Press
the
LOCK
button
twice
with
the
blank
F.A.S.T
.-key
and
the
immobilizer
display
will come
on
for
30
seconds
on
the
information
screen
in the
multi-infor
-
mation displa
y.
12.
This
completes
the
registration
of
the
F.A.S.T.-key.
N00561601
074
Your
F.A.S.T
.-key
operates
on
a radio
fre-
quency
subject
to
Federal
Communications
Commission
(FCC)
Rules
(For
vehicles
sold
in
U.S.A.)
and
Industry
Canada
Rules
(For
vehicles
sold
in
Canada).
This
device
com-
plies
with
Part
15
of
FCC
Rules
and
Industry
Canada licence-exempt RSS standard(s). Operation
is subject
to the
following
two
con-
ditions
.
NOTE
The
ind
icator
light
(5)
comes
on each
time
a
button
is pre
ssed.
The
keyless
entry
system
does
not
work
if
the
key
is in the
ignition switch.
The
F.A.S.
T.-key
can
be
used
from
about 40
feet
(12
m)
away
. However
, this
distance
may
change
if your
vehicle
is near
a TV
trans
mitting
tow
er, a pow
er
station,
or
a
radio
station.
If the UNL
OCK
button
(2)
is pre
ssed whe
n
all
doors
are
locked
and
no
doors
are
opened
within
about
30
seconds
, the
doors
will auto-
matically
re-lock.
If the followi
ng
conditions
are obse
rve
d after
pressing
the
buttons
on
the
remote
control
transmitter
, the battery
in the remo
te cont
rol
transmitter
may need
to be replaced
.
•The doors cannot
be locked or unl
ocked.
•The trunk
lid cannot
be ope
ned.
•The panic alar
m cannot
be ope
rated
.
•The
indicator
light
(5)
is dim
or
does
not
come
on.
If you
lose your
F.A.S.T.-key
, pleas
e contact
an authorized
Mitsubis
hi Motors
dealer
for
a
replacement.If you
wish
to obtain
an
additional
F.A.S.T
.-
key, pleas
e con
tact
an authorized
Mitsubi
shi
Motors
dealer
. A max
imu
m of four
F.A.S.T
.-
key can be
pro
grammed fo
r your vehicle.
To use
the
new
remote
control
transmitters,
it
is necessary
to register
the
key
with
both
the
electronic
immobilizer
and
keyless
entry
sys-
tem. Also refer to “Electronic
immobilizer
(Anti-
theft
starting
system):
Customer
F.A.S.T
.-
key programming” on page 5-28.
General
information

NOTE

Door
locks
5-34
Features and controls
5
This
device
may
not
cause
harmful
inte
r-
ference.This
device
must
accept
any
interference
received,
including
interference
that
may
cause undesired operation.
N0056170
0081
1.Before
replacing
the
battery
, remove
static
electricity
from
your
body
by
touching
a
metal
grounded
object.
2.With
the
Mitsubishi
mark
facing
you,
insert
the
cloth-covered
tip
of
a flat
blade
screwdriver
into
the
notch
in
the
remote
control
transmitter
case
and
use
it to open
the case.
3.Remove the old battery
.
4.Install
a new
battery
with
the
+side
(A)
up.
5.Close
the
remote
control
transmitter
case
firml
y.
6.Check
the
keyless
entry
system
to see
that
it works.
N0050920
0491
CAUTIONChanges
or
modifications
not
expressly
approved
by
the
man
ufactur
er for compli-
ance could
void
the user’s authority
to oper
-
ate
the
equipment.
Pr
ocedur
e for r
eplacing the
remote
contr
ol
transmitter
battery

NOTE
Be
sure
to perform
the
procedure
with
the
Mitsubi
shi mark
facing
you.
If the Mitsubi
-
shi
mark
is not
facing
you
when
you
open
the
remo
te cont
rol transmitter
cas
e, the transmit-
ter
may
come
out.
+ side
- side
Coi
n type
bat-
tery
CR203
2
NOTE
You
may
purchas
e a replacement
battery
at
an electric
appliance
store.
Your
authorized
Mitsubi
shi Mot
ors
dealer
can
replace
the battery
for
you
if you
pre
fer.
CAUTIONWhen the remo
te control
transmitter
cas
e is
opened,
be
careful to keep
water
, dust, etc.
out.
Also,
do
not
touch
the
internal
compo-
nen
ts.
Door locks
W
AR
NING
Mak
e sur
e all
doors
are tigh
tly
clos
ed and
locked
while
driving.
•Locked
doors,
in
combination
with
the
use
of seat
belts,
can
help
reduce
the
risk
of ejection
in an
accident.
•Locked
doors
can
help
keep
passengers,
especially
small
childr
en,
from
opening
doors
and
falling
out
of moving
vehicles.