2015 MITSUBISHI iMiEV door lock

Power window control
Features and controls 5-15
5
N00548700127
The main switch located on the driver’s door can be used to opera
te all the windows.
A window can be opened
or closed by operat-
ing the corresponding switch. Press the switch down to open the window,and pull up the switch to close it. If the driver’s door window switch is fully pressed down, the driver’s door window auto- matically opens completely. If you want to stop the window movement,operate the switch lightly in the reverse direc- tion.
N00548800115
Each sub-switch can be
used for it’s own pas-
senger door window, unless the driver’s win-dow lock switch is activated.
N00548900145
The power windows can be run up or downwhen the electric motor switch is in the “ON” position. The door windows can be opened or closedfor a 30-second period after the electric motor switch is turned to the “ACC” or “LOCK” position. However, once the driver’s door orthe front passenger’s door is opened, the power windows cannot be operated.
N00549000156
When this switch is in the lock mode, the pas-senger door switches cannot be used to open or close the door windows, and the mainswitch will open or close only the driver’s door window. To unlock the switch, press it again.
Main switch 1- Driver’s door window switch2- Front passenger door window switch3- Left rear door window switch 4- Right rear door window switch 5- Lock switch
Sub switch 1- Close2- OpenPower window timer function
Lock switch 1- Lock 2- UnlockWA R N I N G Before driving with a child in the vehicle, be sure to lock the window switch to make it inoperative. Children tampering withthe switch could easily trap their hands or heads in the window.
BK0209800US.book 15 ページ ２０１４年１月１４日　火曜日　午前９時２６分

Steering wheel lock 5-20 Features and controls
5
N00571700013
If the driver’s door is opened while the elec- tric motor switch is in the “LOCK” or “ACC” position, a tone will sound.
N00512500209
Remove the key at
the “LOCK” position.
Turn the steering wheel until it is locked. Turn the key to the “ACC” position while moving the steering
wheel slightly.
N00571800014
1. Make sure all occupants are properly seated with seat belts fastened. 2. Insert the key. 3. Make sure the parking brake is applied.4. Press and hold the brake pedal down with your right foot. 5. Make sure the selector
lever is in the “P”
(PARK) position.
6. Turn the key to the “ON” position and make certain that all warning lights arefunctioning properly before starting the electric motor unit. 7. Turn the key to the “START” position forone to two seconds, and
slowly return it to
its original position. When you hear the startup sound and the ready indicatorcomes on, startup of the electric motor unit is complete.
If the driver’s door is opened while the key is in the “ON” position, the electric motorreminder buzzer sounds
intermittently to
remind the key is in the electric motor switch.
Key reminder buzzer Steering wheel lock To l o c k To u n l o c k
CAUTION Remove the key when leaving the vehicle.If your vehicle needs to be towed, turn the key to the “ACC” position to unlock the steering wheel.NOTE
 If the front wheels are turned, the anti-theft lock may sometimes make it difficult to turnthe key from “LOCK”
position to “ACC”
position. Firmly turn the steering wheel to the left or to the right as you turn the key.
Starting the electric motor unit
CAUTION Never attempt to start the electric motor unit by pushing or pulling the vehicle.
Electric motor reminder
BK0209800US.book 20 ページ ２０１４年１月１４日　火曜日　午前９時２６分

Indicator and warning light package
Features and controls 5-41
5
N00519801862
Indicator and warning light package 1- Low energy warning indicator
 P.5-40
2- Selector lever
position indicator
 P.5-21
3- Acoustic Vehicle Alerting System
( AVA S ) i n d i c a t o r
 P.5-23
4- High-beam indicator
 P.5-42
5- Turn-signal indicators/Hazard warning
lights
 P.5-42
6- Position indicator
 P.5-42
7- Front fog light indicator
 P.5-42
8- Service reminder
 P. 5 - 3 6
9- Outside air temperature warning indi-
cator
 P. 5 - 3 9
10- Regenerative brake system indicator
 P.5-42
11- Ready indicator
 P.5-42
12- Tire pressure moni
toring system warn-
ing light
 P.5-31
13- 12V starter battery charging system
warning light
 P.5-43
14- Electric power steering system warning
light
 P.5-28
15- Electric motor unit warning light
 P.5-43
16- Brake warning light
 P. 5 - 4 2
17- Anti-lock braking system warning light
 P.5-26
18- Power down warning light
 P.5-43
19- Active stability control (ASC) indicator
 P.5-30
20- Active stability control (ASC) OFF
indicator
 P. 5 - 3 0
21- Charging indicator
 P.5-42
22- Theft-alarm indicator
 P.5-12
23- Door-ajar warning light
 P.5-43
24- Driver’s seat belt reminder/warning
light
 P. 4 - 1 0
25- Supplemental Restra
int System (SRS)
warning light
 P.4-13
BK0209800US.book 41 ページ ２０１４年１月１４日　火曜日　午前９時２６分

Combination headlights and dimmer switch
Features and controls 5-45
5
[When the ready indicato
r is not illuminated,
or when the ready indicator is illuminated but the parking brake is not released] The electric motor unit starts when the lights are off.
N00532600554
 If the key is turned to “LOCK” or “ACC” position or removed from the electric motor switch and the driver’s door is opened with the comb
ination headlights
and dimmer switch in the “ ” or “ ” position, the lights automatically turn off.
• If the driver’s door is opened after the key is removed from the electric motorswitch, a buzzer will sound to remind you to turn off the lights. • If the driver’s door is opened with thekey in the electric motor switch, a buzzer will sound intermitte
ntly to remind you
to remove the key.
 If the key is turned to “LOCK” or “ACC” position with the driver’s door closed and the combination headlights and dimmer switch in the “ ” or “ ” position, the lights will stay on for about 3 minutes and then turn off automatically.
If the combination
headlights and dimmer
switch is turned to the “ ” or “ ” posi- tion again after the electric motor switch is turned to “LOCK” or “ACC” position, the auto-cutout function described above will not work. The lights (the park
ing lights, tail lights
The daytime running lights illumi- nated Parking, tail, front
and rear side-
marker lights, license plate and instrument panel lights on Headlights and other lights on
NOTE
 Once the daytime running light come on, they do not go out until the electric motorswitch is turned to the “LOCK” or “ACC” position.OFF All lights off AUTO
Headlights and other lights turn on and off automatically in accor-dance with outsi
de light level.
Parking, tail, front
and rear side-
marker lights, license plate and instrument panel lights on Headlights and other lights on
NOTE
 The sensitivity of the automatic on/off con- trol can be adjusted.For further information, please contact a cer-tified i-MiEV dealer.  Do not place anything on the sensor (A), and do not clean with a gla
ss cleaner. Clean only
with clear water.  If the lights do not turn on or off with the switch in the “AUTO”
position, manually
operate the switch. Have the system checked by a certified i-MiEV dealer.
Light auto-cutout function (headlights and other lights)
NOTE
 The light auto-cutout f
unction can be deacti-
vated. See a certified i-MiEV dealer for details.
When you want to keep the lights on:
BK0209800US.book 45 ページ ２０１４年１月１４日　火曜日　午前９時２６分

Interior lights 5-52 Features and controls
5
The accessory can be operated when the elec- tric motor switch is in the “ON” or “ACC”position. To use a “plug-in” type
accessory, open the
cover, then insert the plug in the socket.
N00525300559
N00525800222
The dome light can be turned on by sliding the dome light switch.
Interior lights 1- Dome light (Rear)
 P.5-53
2- Dome light (Fr
ont)/Reading lights
 P.5-52
Dome light (Front)/Reading lights
(if so equipped)
Dome light (Front)

1- Door 2- Off 1- (DOOR)
 The dome light comes on when any door or the liftgate is opened. It goes off approximately 30 seconds afterthe door or liftgate is closed (delayed off function). However, the light goes off immediately if:• The door and the liftgate are closed and the electric motor switch is turned to the “ON” position.• The driver’s door is closed after all the other doors are closed while the lock knob of the driver’s door is in the lock position. • The door and the liftgate are closedand the power door lock switch is used to lock the doors. • The keyless entry system remotecontrol transmitter is used to lock the doors.
BK0209800US.book 52 ページ ２０１４年１月１４日　火曜日　午前９時２６分

Interior lights
Features and controls 5-53
5
N00553800096
Regardless of the dome light switch position, when you press the lens, the light on the sidethat is pressed illumi
nates; when you press
the lens again, the light goes off.
N00525400459
The rear dome light can be turned on by slid- ing the dome light switch.
 If the dome light is left switched on with the electric motor switch in the “LOCK” or “ACC” position and adoor or the liftgate is opened, it goes off automatically after approxi- mately 30 minutes.The light will illuminate again after it automatically goes off in the fol- lowing cases:• When the electric motor switch is turned to the “ON” position. • When the keyless entry system remote control transmitter is oper- ated.• When any of the doors or the lift- gate is opened after all doors and the liftgate are closed.
NOTE
 When the key is removed while the doors and liftgate are clos
ed, the dome light will
illuminate for approximately 30 secondsbefore going off.  The time until the light goes off (delayed off) can be adjusted. See a certified i-MiEV dealer for details. However, the dome light
will shut off in sync
with the automatic relocking function, even if the dome light dela
yed off function has
been extended. For the automatic relockingfunction, refer to “Keyless entry system” on page 5-5.
 The auto cut-out functi
on can be deactivated.
See a certified i-MiEV dealer for details.2- The dome light goes off.
Reading lights

Dome light (Rear)
NOTE
1- On2- Door 3- Off 1- (ON) The dome light comes on.2- (
)
BK0209800US.book 53 ページ ２０１４年１月１４日　火曜日　午前９時２６分

Storage spaces 5-54 Features and controls
5
N00526400502
 The dome light comes on when any door or the liftgate is opened. It goes off approximately 30 seconds afterthe door or liftgate is closed (delayed off function). However, the light goes off immediately if:• The door and the liftgate are closed and the electric motor switch is turned to the “ON” position.• The driver’s door is closed after all the other doors are closed while the lock knob of the driver’s door is in the lock position. • The door and the liftgate are closedand the power door lock switch is used to lock the doors. • The keyless entry system remotecontrol transmitter is used to lock the doors.
 If the dome light is left switched on with the electric motor switch in the “LOCK” or “ACC” position and adoor or the liftgate is opened, it goes off automatically after approxi- mately 30 minutes.The light will illuminate again after it automatically goes off in the fol- lowing cases:• When the electric motor switch is turned to the “ON” position. • When the keyless entry system remote control transmitter is oper- ated.• When any of the doors or the lift- gate is opened after all doors and the liftgate are closed.
NOTE
 When the key is removed while the doors and liftgate are clos
ed, the dome light will
illuminate for approximately 30 secondsbefore going off.  The time until the light goes off (delayed off) can be adjusted. See a certified i-MiEV dealer for details. However, the dome light
will shut off in sync
with the automatic relocking function, even if the dome light dela
yed off function has
been extended. For the automatic relockingfunction, refer to “Keyless entry system” on page 5-5.
 The auto cut-out func
tion cannot be
operated
when the dome light switch is in the “ON”position.Also, this function
can be deactivated.
See a certified i-MiEV dealer for details.3- (OFF) The dome light goes off.
Storage spaces
CAUTION Never leave lighters,
carbonated drink cans,
or spectacles in the cabin when parking thevehicle in hot sunshine. The cabin will become extremely hot,
so lighters and other
flammable items ma
y catch fire and
unopened drink cans (i
ncluding beer cans)
may rupture. The heat may also deform or crack plastic spectacle parts. Keep the lids of storage spaces closed while driving the vehicle. A lid or the contents of astorage space could ot
herwise cause injuries
during a sudden stop.NOTE
 Do not leave valuables in any storage space when leaving the vehicle.NOTE
BK0209800US.book 54 ページ ２０１４年１月１４日　火曜日　午前９時２６分

Vehicle preparatio
n before driving
Driving safety 6-3
6
from moving forward
and possibly interfering
with the operation of the pedals, Mitsubishigenuine floor mats are recommended.
N00628700063
1. Place the floor mat to fit the shape of thefloorboard. 2. Align the floor mat with the installation holes over the retaining clips. 3. Secure the floor mat with retaining clips.
N00629000698
For a safer and more enjoyable trip, always observe the following:  Before starting the ve
hicle, make certain
that you and all passengers are seated andwearing their seat belts properly (with children in the rear seat, in appropriate restraints), and that all the doors and therear hatch are locked.
To install the floor mat
NOTE
 The shape of the mat and the number of retaining clips may
vary depending on the
vehicle model.
WA R N I N G If a floor mat is the
wrong size or is not
properly installed, it can interfere with theoperation of the pedals. Interference withthe pedals can cause unintended accelera- tion and/or increased stopping distances resulting in a cras
h and injury. Always
make sure the floor mat does not interfere with the accelerator or brake pedal. Always use the reta
ining clip on the
driver’s floorboard to secure the floor mat. Always install the mat with the correct side facing down. Never install a second
mat over or under
an existing floor mat. Do not use a floor mat designed for another model vehicle even if it is aMitsubishi genuine floor mat. Before driving, be sure to check the fol- lowing:• Periodically check that the floor mat isproperly secured with the retaining clips. If you remove the floor mat while clean- ing the inside of you
r vehicle or for any
other reason, always check the condition of the floor mat after it has been rein- stalled.• While the vehicle is stopped with theelectric motor unit off, check that thefloor mat is not interfering with the ped- als by depressing the pedals fully.
Vehicle preparation before driving Seat belts and seats
BK0209800US.book 3 ページ ２０１４年１月１４日　火曜日　午前９時２６分