2015 AUDI Q5 light

M N
co
a:
co
,...., \!) 1.1'1
N 1.1'1 ,....,
USA models: Parking brake
¢page 18
Canada models: Parking brake
¢page 18
USA models: Brake malfunction
¢page 18
Canada models: Brake malfunc­
tion
c> page 18
In vehicles with adaptive cruise control* addition­
al indicator lights are displayed
c>page 109.
A WARNING
- Failure to heed warning lights and other im­
portant vehicle information may result in
serious personal injury or vehicle damage.
- Whenever stalled or stopped for repair,
move the vehicle a safe distance off the
road, stop the engine, and turn on the emer­
gency flasher
c> page 54.
- The engine compartment of any motor vehi­
cle is a potentially hazardous area. Before
you check anything in the engine compart­
ment, stop the engine and let it cool down.
Always exercise extreme caution when work­
ing under the hood
c> page 221
@ Tips
Many functions are monitored by the Auto­
Check system
c> page 2 7. Malfunctions or
faults will be identified either with a red sym­
bol (priority 1 - Danger!) or with a yellow
symbol (priority 2 -Warning).
EPC Electronic power control
App lies to vehicles: with gaso line engine
This warning/indicator light monitors the elec­
tronic power control .
The Ga warning/indicator light (Electronic Power
Control) illuminates when you turn on the igni­
tion as a function check.
@ Tips
If this warning/indicator light illuminates
while you are driving, then there is a malfunc-
Instruments and indicator lights
tion in the engine electronics. Have the mal­
function corrected as soon as possible by your
authorized Audi dealer or qualified workshop.
W Glow plug system
Applies to vehicles: wit h diese l eng ine
The control light illuminates when the glow plug
system is active.
If the II indicator light illuminates, the glow
plug system is active. You should start the engine
immediately after the indicator light switches off.
The indicator light only illuminates for approxi­ mately 1 second if the engine is warm or if the
outside temperature is above 46 QF (8 Q().
(D Tips
-If the glow plug indicator light illuminates
while driving, there is an engine control
malfunction. The engine should be checked
immediately.
- If the indicator light does not illuminate at
all when switching the ignition on, there
may be a malfunction in the glow plug sys­
tem. The engine should be checked.
;;.ll/4 Electronic Stabilization Control (ESC)
If the Bl indicator light blinks while driving, the
ESC or ASR (Anti-Slip Regulation) is actively regu­
lating.
If the
Bl indicator light turns on, the system has
switched the ESC off. In this case, you can switch
the ignition off and then on to switch the ESC on
again. The indicator light turns off when the sys­
tem is functioning fully.
If the. indicator light turns on, ESC was re­
stricted using the
!.P-O FF I button c> page 191.
Stabilization control (ESC/ABS): Fault! See
owner's manual
If the Bl indicator light and the ABS indicator
light
LtB (USA models) 1iJ (Canada models)
turn on and the message appears, the ABS or
electronic differential lock is malfunctioning . This
also causes the ESC to malfunction. The brakes ..,.
15

Instruments and indicator lights
still fu nction with their normal power, but A BS is
not active .
D rive to y our a uthorize d Au di d eale r o r q ual ified
wo rkshop immediately to have the ma lf u nction
corrected .
A WARNING
If the .. (USA models) . (Canada mod­
els) brake system indicator light turns on to­
gether with the ABS and ESC indicator lights ,
the ABS/ESC regulating function may have
failed . Functions that stabilize the vehicle are
no longer available . Th is could cause the vehi­
cle to swerve and increase the risk of sliding .
Dr ive caref ully to the nearest autho rized Aud i
de aler or o ther qualified wor kshop and have
t he malfunction corrected .
(D Tips
For addit iona l information on ESC and ABS,
refer to
¢ page 191.
CJ};/ !f Safety systems
-
The II (USA models) a (Cana da models) indi ­
cator light monito rs the safety systems (e .g . air ­
bags, pretensione rs) and illuminates for a few
seconds each time you switch t he ignition on.
If t h e II (U SA mode ls) a (Canad a models) in­
d icator light does not go out, or if it i llum inates
while you are driving, or if it starts to blink, then
there is a malfunction somewhe re in the system.
I f the light does not ill uminate when you switch
the igni tion on, this also means there is a mal­
function .
A WARNING
If you have a mal func tion in the safety sys­
t ems, contact your authorized A udi dealer im­
media tely. Othe rwise the safety system s may
no t w or k properly in an a cci den t.
16
ill Tire pressure monitoring system -
telltale indicator lamp
Applies to vehicles: with tire pressure monitoring system
The warning/indicator light appears in the event
of a signifi cant loss of tire pressure or if there is
a malfunction.
The ind icator light RI] illumi nates to check the
func tion when yo u sw itch on t he ign it io n.
If the
RI] symbo l rema ins on or blinks after you
switch on the ignition, the re is a loss of tire pres­
su re or a system ma lfunction .
If there is a system
malfunction, see your author ized Audi dealer as
soon as possib le.
Deta iled info rmat ion on the tire pressure mo ni­
tor ing system ca n be found in
¢page 252.
¢¢Turn signals
The indicator light blinks when you use either
turn signal .
Whenever you use the left B or the right R
turn s ignal, the indicator light blinks . When you
use the eme rgency flashers, bot h in d icator lights
flash .
If one of the turn signa l ligh t bulbs burn out, the
turn s ignal will b link twice as fast as normal.
This does not apply, however, in towing mode.
The ind icator light does not flash if a turn signa l
i s out on the tra iler or the towing veh icle. Add i­
tiona l information on the turn signa ls
¢ page 55.
¢1.~ Trailer turn signal assembly
Applies to vehicles: with towing hitch
The indicator light also blinks if the turn signal is
operated when towing a trailer .
The indicator light . blinks when the t urn s ig ­
nal is used, if a trai ler has been properly co nnect­
ed to the ve hicle .
If one of the tu rn signa l bulbs on the t railer is
burned out or defective, the ind icator light will
not blink when you use the turn signa ls.

M N
co
a:
co
,...., \!) ..,.,
N ..,., ,....,
@ Tips
For vehicles with a factory installed towing
hitch or a trailer hitch that was installed later
according to factory specifications, the trailer
turn signal assembly is actuated.
~ Safety belts
This warning/indicator light reminds you to put
on your safety belt.
The . warning/indicator light illuminates when
the ignition is switched on to remind the driver
and (on USA models only) any front passenger to
put on the safety belt. Additionally, an audible
warning tone will also sound .
For more Information ¢
page 144, Safety belt
warning light.
o Malfunction Indicator Lamp (MIL)
The Malfunction Indicator Lamp (MIL) is part of
the On -Board Diagnostic (OBD II) system . The
symbol ¢4 lights up when the ignition is turned
on and w ill turn off after the engine has started
and has settled at a constant idle speed. This in­
dicates that the MIL is working properly .
The warning light illuminates when there is a
malfunction in the engine electronic system.
Contact your authorized Audi dealer and have the
mal funct ion corrected.
An improperly closed fuel filler cap may also
cause the MIL light to illuminate (only vehicles
with gasoline engine)
¢page 216.
For more informat ion ¢ page 26.
[D High beam
The . warning/ind icator light illuminates when
the high beams are on or when you use the head­
light flasher. For more info rmation about using
the high beams, see
~ page 55.
Instruments and indicator lights
CRUISE/•(-) Cruise control
The (~jll)~i* (USA models) ;Bl (Canada models)
warning/ind icator light illuminates when the
cruise control is activated.
ABS/{ @) Anti-lock brake system (ABS)
This warning/indicator light monitors the ABS
and the electronic differential lock (EDL).
The~ (USA models) !(iJ (Canada mode ls)
warning/indicator light will come on for a few
seconds when the ignition is switched on. The
light will go out after an automatic check se­
quence is comp leted .
There is a malfunction in the ABS when:
-The warning/indicator light does not illum inate
when you sw itch on the ignit ion.
- The warning/indicator light does not go out af­
ter a few seconds.
- The warning/ indicator light illum inates while
driving .
The brake system will still respond even with·
out the assistance of the ABS system. See your
authorized Audi dealer as soon as possible to re­
store full braking performance.
For more infor­
mation regarding the ABS
~page 191.
The ABS warning light and the brake warning
light come on together . The ABS will not work
and you will notice a change in braking re­
sponse and performance.
Malfunction in the brake system
If the brake warning light¢ page 18 and the
ABS warning illum inate
together there may be a
malfunction in the ABS, and there may also be a
malfunction in the brake system itself~ ,&..
In the event of a
malfunction in the brake sys ­
tem
the warning/ind icator light 1111 (USA mod­
els)/ . (Canada mode ls) in the instrument clus­
ter flashes. By press ing the
!SE TI button, you can
bring up a dr iver message which exp lains the
malfunction in more detail. Please note
~page 28.
17

Instruments and indicator lights
Malfunction in th e electronic diffe rential
lock (EDL )
The EDL works together with the ABS . The ABS
warning light wi ll come on if there is a malfunc­
t ion in the EDL system
q page 191 . See your au­
t hor ized Audi dealer as soon as possible.
A WARNING
- If the Lil3 (USA models) ;[IJ (Canada mod ­
els) warning light does not go out , or if it
comes on while d riving, the ABS system is
not working properly. The vehicle can the n
be stopped only with the standard brakes
(without ABS) . You wi ll not have the protec­
tion ABS p rovides . Contact your authorized
Audi dealer as soon as possible .
- If the
1111 (USA models)/ . (Canada mod­
els) brake system indicator light t urns on to ­
gether wit h the ABS and ESC indicator
lights , the ABS/ESC regulating function may
have failed. Funct ions that stab ilize the ve­
hicle are no longer availab le. This could
cause the vehicle to swerve and increase the
risk of sliding . Driv e ca refully to the nea rest
autho rized Aud i dealer o r othe r qualified
wor kshop and have the malfunction correc t­
ed.
:fil .lC® ) Electromechanical parking brake
The warning/indicator light monitors the elec­
trome chanical parking brake.
W ith the parking brake applied and the ign it ion
turned on, the. (USA models)/ . (Cana-
da models) warning/indicator light illuminates.
Afte r the ig nitio n has been turned off , the warn­
ing/indicator light continues to illum inate fo r
about 30 seconds . If the parking brake is applied
w ith the ignition t urned off, the warning/indica­
tor light illuminates for abo ut 30 seconds.
The warning/indicator ligh t will go o ut when t he
parking brake is re leased .
-
If the war ning/ indicato r light flashes cont inuous­
ly
after applying the p ark ing brake , brak ing fo rce
is no t sufficient to prevent the vehicle from roll­
ing unintentiona lly . Please note the following:
18
- I f the slope of the ground is too steep to pa rk
the vehicle, the add itiona l driv e message ap ­
pears
Caution: Vehicle parked too steep.
- In the event of a pa rking brake malfunction ,
the yellow
Ill symbol appears in the instru­
ment cluster display and the driver message
Pa rk ing brake malfunction! is displayed. Have
the malfu nction repaired as soon as possible by
an authorized A udi dealer or any other qualified
workshop .
BRAKE/C(D) Brake system
The warning/indicator light flashes if brake fluid
level is low, if there is an ABS system malfunc­
tion or a parking brake malfunction .
The 1111 (USA models)/ . (Canada models)
l ight illum inates when the ignition is turned on .
It goes out after the engine has been started.
This ind icates that the brake warn ing light is
fun ct io ni ng properly.
If th e brake warning light does not light up
when the engine is cranking, there may be a
malfunction in the electrical system. In this
case, conta ct an authorized Audi dealer .
If the brake system warning/indicator light flash­
es, there is a brake system malfunction . By press­
i ng the
IS ET I button , you can b ring up a dr iver
message wh ich explains the malfunction in mo re
d etail
q page 28.
If the ABS fails, the ABS wa rn ing/ indicator lig ht
9 (USA models)! IIJ (Canada mode ls) flashes
togethe r wi th the b rake system wa rning/ind ica ­
tor lig ht
q ,&. .
(USA mode ls): If the war ning light 1111 a nd the
warning
light Ei'I illuminate together, immedi­
ate ly conta ct yo ur autho rized Aud i dea le r or
q ualifie d workshop to have all brake pads in­
spected
q page 32 .
When the light comes on , a n aud ible warn ing sig-
nal is also given. .,.

M N
co
a:
co
,...., \!) ..,.,
N ..,., ,....,
A WARNING ,~
- If the 1111 (USA models)/ . (Canada mod­
els) brake system indicator light turns on to­
gether with the ABS and ESC indicator
lights, the ABS/ESC regulating function may
have failed. Functions that stabilize the ve­
hicle are no longer available. This could
cause the vehicle to swerve and increase the
risk of sliding. Drive carefully to the nearest
authorized Audi dealer or other qualified
workshop and have the malfunction correct­
ed.
- If the brake warning/indicator light does
not go out after a few seconds and the park­
ing brake is released, or lights up while you
are driving, the fluid level in the brake fluid reservoir is too low. If you believe that it is
safe to do so, proceed immediately at low
speed to the nearest authorized Audi dealer
or qualified repair facility and have the
brake system inspected.
- Always keep in mind that after several brake
applications, you will need greater pressure
on the brake pedal to stop your vehicle. Do
not rely on strained brakes to respond with
maximum stopping power in critical situa­
tions. You must allow for increased braking
distances. The extra distance used up by
fading brakes could lead to an accident.
Instruments and indicator lights
19

Driver information system
Driver information
system
Introduction
General notes
The driver information display inside the instru­
ment cluster provides you, the driver, with much
useful information .
Fig. 9 Instrument cluster: center display
Information from the driver information system
is shown in the display in the center of the instru­
ment cluster .
When you turn on the ignition and while you are driving, some functions and vehicle components
are scanned for their operating status. Malfunc­
tions or required service procedures are s ignaled
aud ibly and shown by red and yellow lighted sym­
bols and reminders to the driver in the display.
The driver is also shown information about radio
and CD operation and directions for the nav iga­
tion system* . You can find additional informat ion
on these subjects in the radio or
MMI" manual.
The illustrations in the instrument panel display
differ in some of the vehicles.
The driver information system provides the fol­
lowing functions :
Sound system disp lay ¢
page20
Outside air temperature ¢page 21
Digital speedometer ¢
page 21
Open door- and luggage com- ¢page 21
partment warning
Service interval display ¢page22
Auto Check system ¢page27
20
Driver information ¢
page 27
Speed warn ing ¢
page94
Trip computer ¢page22
Tire pressure monitoring system* ¢page
252
Digital clock with date display ¢page 12
Odometer and trip odometer ¢
page 13
Selector lever position r::>page 123
Cruise control ¢
page95
Adapt ive cruise control* ¢page 107
Energy flow disp lay* r::>
page 104
@ Tips
In the event of a malfunction either a red or
ye llow icon appears in the display. Red sym­
bols indicate
Danger¢ page 28. Yellow
symbols ind icate a
Warning r::>page 31.
Sound system display
Fig. 10 D isplay: sou nd system
If priority 1 or priority 2 faults are not shown by
the Auto Check Contro l, the name of the radio
station you are tuned to or the frequency and the
reception range are shown in the upper area of
the d isplay .
When the CD is in use, the tit le of the track being
played is shown. The CO changer d isplays the
number of the current CO (CDl to CD6).

M N
co ~ co
rl I.O
"' N
"' rl
Outside temperature display
Fig. 11 Display: outside temperature
~ ,.._
9 a:
lll
At temperatures below 39 °F (+4 °C), a snowf lake
symbol appears in front of the temperature dis­
play.
It is intended to rem ind the driver to pay
specia l attent ion to
ic e on the r oad .
If the vehicle is stationary, or if you are driving at
a very low speed, the temperature shown in the
d isplay m ight be slightly higher than the actual
outside temperature. This is caused by the heat be ing radiated from the eng ine.
The unit of measurement for the temperature
can be set in either °For in °Con the
MMI* or on
the radio control unit. The outs ide temperature
d isp lay automatically shows the unit of meas ure­
ment that has been set. For add itional info rma­
tion, see the
MMI * or the radio instruction man ­
ua l.
_& WARNING
-Never use the outside temperature d isp lay
to determine if a road surface is icy or not.
Keep in m ind that road surfaces, especially
br idges and overpasses, could be ice covered
and slippery even at an outs ide temperature
above 39 °F (+4 °C).
- Always remember, even if the "snowflake"
symbol ( ice warn ing) does not appear in the
display, black ice could be on the road.
-Always reduce your speed and dr ive with
special care in cold weather conditions when
the chance of encounteri ng icy road surfaces
in creases.
Dr iver inform atio n sy stem
Digital speedometer
Fig. 12 Display: Digital speedometer
Current speed appears in the display. Speed is
shown in
1 mph increme nts (USA models) or 1
km/h increments (Canada models).
You can switch the display from miles to kilome­
ters and vice versa via the radio or
MMI*.
Open door or trunk lid warning
The pictogram alerts you when doors or the
trunk lid have been left open.
Fig. 13 Display: Open door· a nd trunk lid wa rning
~.., 0 .,, 0 er. 0) m
The Open Door/Trunk L id war ning displays if even
one doo r, the hood or the t runk lid is open. This
symbol a lso shows
which door or lid has no t been
closed
~fig. 13.
As soon as the doo r, the hood and the trun k lid
are closed properly, the door and trunk lid warn­
ing turns off and the selected driver information
system f unctions are displayed aga in .
21

Driver information system
On Board Diagnostic
System (OBD)
Malfunction Indicator Lamp (MIL)
The Malfunction Indicator Lamp (MIL) ¢• in the
instrument cluster
c:::> page 14, fig. 8 is part of the
On-Board Diagnostic (OBD II) system.
The warning/indicator light i lluminates when the
ignition is switched on and goes out after the en­
gine starts and the idle has stabilized. This indi­
cates that the MIL is working properly.
If the light does not go out after the engine is
started, or illuminates while you are driving, a
malfunction may exist in the engine system. If
the light illuminates, the catalytic converter
could be damaged.
Continue driving
with reduced power (avoiding
sustained high speeds and/or rapid acce lerations)
and have the condition corrected. Contact your
authorized Audi dealer.
I f the light illuminates, the electronic speed lim­
iter may also be malfunctioning. For more infor­
mation
c::> page 26, Electronic speed limiter.
An improperly closed fuel filler cap may also
cause the MIL light to illuminate (only vehicles
with gasoline engine)
c:::> page 216.
On-Board Diagnostics
F ig . 21 Locat ion of Data link Connector (DLC)
On-Board Diagnostics monitors the components
of yo ur emission control system. Each monitored
component in your engine system has been as­
signed a code . In case of a malfunction, the com­
ponent will be identified and the fault stored as a
code in the control module memory.
26
The MIL light may also illuminate if there is a
l eak in the on-board fuel vapor recovery system.
If the light illuminates after a refueling, stop the
vehicle and make sure the fuel filler cap is prop­
erly closed (only vehicles with gasoline engine)
c::> page 216.
In order to make an accurate diagnosis, the stor ­
ed data can only be displayed using specia l diag­
nostic equipment (generic scan tool for OBD).
In order to connect the specia l diagnostic equip­
ment, push the plug into the Data Link Connector
(DLC) . The DLC is located to the right of the hood
release
c::> fig. 21.
Your authorized Audi dealer or qualified work­ shop can interpret the code and perform the nec­
essary repair .
A WARNING
Do not use the diagnostic connector for per­
sonal use. Incorrect usage can cause malfunc­
tions, which can increase the r isk of a coll i­
sion!
Electronic speed limiter
Your vehicle may be factory equ ipped with tires
that are rated for a maximum speed of 130 mph
(210 km/h) . Th is is less than the max imum speed
of your veh icle. To reduce the risk of sudden tire
failure and loss of control if the vehicle is ope rat­
ed at excessive speeds, your vehicle also has an
electronic speed limiter . The electronic speed
limiter prevents your vehicle from going faster
than the tire speed rating. For more information
c::> page 242.
If the engine contro l unit receives faulty vehicle
road speed signals, the Malfunction Indicator
Lamp (MIL) ¢•will illuminate. If this occurs,
contact the nearest authorized Audi dealer for as­
sistance.
SQS
Your vehicle's top speed is electronically limited
to 155 mph (250 km/h).
If the engine contro l unit receives faulty vehicle
road speed s ignals, the Malfunction Ind icator ..,_