2014 TOYOTA DYNA 100/150 wheel torque

IN CASE OF AN EMERGENCY161
CAUTION
DWhen lowering the vehicle, make
sure all portions of your body and
all other persons around will not be
injured as the vehicle is lowered to
the ground.
DHave the wheel nuts tightened with
torque wrench to the following
torques, as soon as possible after
changing wheels. Otherwise, the
nuts may loosen and the wheels
may fall off, which could cause a
serious accident.
DYNA 100


135 N·m (13.8 kgf·m, 100 ft·lbf)
DYNA 150

365 N·m (37.2 kgf·m, 269 ft·lbf)

: See “Model code” on page vi in the
beginning of this manual if you are not
sure of your vehicle model.
10. Reinstall the wheel ornament.
To reinstall the wheel ornament, tighten
the bolts by turning them clockwise with
the open−end wrench.
CAUTION
Take due care in handling the orna-
ment to avoid unexpected serious in-
jury.
Dyna100/150_EE
—Reinstalling wheel
ornament

162IN CASE OF AN EMERGENCY
11. Check the air pressure of the re-
placed tire.
Adjust the air pressure to the specification
designated on page 218 in Section 8. If
the pressure is lower, drive slowly to the
nearest service station and fill to the cor-
rect pressure.
Do not forget to reinstall the tire inflation
valve cap as dirt and moisture could get
into the valve core and possibly cause air
leakage. If the cap is missing, have a new
one put on as soon as possible.
12. Restow all the tools, jack and flat
tire securely.
Front and single rear tires—
As soon after changing wheels as pos-
sible, tighten the wheel nuts to the torque
specified on page 218 in Section 8 with
a torque wrench. Have a technician repair
the flat tire.
Double rear tires—
As soon after changing wheels as pos-
sible, tighten the stop bolts and wheel
nuts to the torque specified on page 218
in Section 8 with a torque wrench. Have
a technician repair the flat tire.
This is the same procedure for changing
or rotating your tires.
CAUTION
Before driving, make sure all the
tools, jack and flat tire are securely
in place in their storage location to
reduce the possibility of death or se-
rious injury during sudden braking,
sudden swerving or an accident.
If your vehicle becomes stuck in snow,
mud, sand, etc., then you may attempt
to rock the vehicle free by moving it
forward and backward.
CAUTION
Do not attempt to rock the vehicle
free by moving it forward and back-
ward if people or objects are any-
where near the vehicle. During the
rocking operation the vehicle may
suddenly move forward or backward
as it becomes unstuck, causing injury
or damage to nearby people or ob-
jects.
NOTICE
If you rock your vehicle, observe the
following precautions to prevent dam-
age to the transmission and other
parts.
zDo not race the engine and avoid
spinning the wheels.
zIf your vehicle remains stuck after
rocking the vehicle several times,
consider other ways such as tow-
ing.
Dyna100/150_EE
—After changing wheelsIf your vehicle becomes
stuck

218SPECIFICATIONS
Tire size and cold tire inflation pressure:
Dyna 100


Tire sizeTire inflation pressure
kPa (kgf/cm2or bar, psi)
195/70R15C450 (4.50, 65)
Dyna 150

Tire sizeTire inflation pressure
kPa (kgf/cm2or bar, psi)
195/70R15CFrontRear195/70R15C450 (4.50, 65)350 (3.50, 51)
Wheel nut torque, N·m (kgf·m, ft·lbf):
Dyna 100

135 (13.8, 100)
Dyna 150
365 (37.2, 269)
NOTE: For a complete information on tires (e.g. replacing tires or replacing wheels), see
“Checking tire inflation pressure” through “Replacing wheels”, pages 193 through
197, in Section 7−2.

: See “Model code” on page vi in the beginning of this manual if you are not sure of
your vehicle model.
Dyna100/150_EE
Tires