2014 TOYOTA DYNA 100/150 ECO mode

28SEATS, SEAT BELTS, STEERING WHEEL AND MIRRORS
Toyota strongly urges that the driver and
passengers in the vehicle be properly re-
strained at all times with the seat belts
provided. Failure to do so could increase
the chance of injury and/or the severity of
injury in accidents.
The seat belts provided for your vehicle
are designed for people of adult size,
large enough to properly wear them.
Child.Use a child restraint system ap-
propriate for the child until the child be-
comes large enough to properly wear the
vehicle’s seat belts. Toyota recommends
you use a child restraint system which
conforms to the regulation “ECE No.44”.
See “Child restraint” on page 44 for de-
tails.
Single cab models

:
DIf a child is too large for a child re-
straint system, the child should sit in
the seat and must be restrained using
the vehicle’s seat belt.
DWithout passengers’ seat belts—We
recommend installing thepassengers’
seat belts on your vehicle. Ask any
authorized Toyota dealer or repairer, or
another duly qualified and equipped
professional, if passengers’ seat belts
can be installed on your vehicle. If
installation is possible, put the child in
the passenger ’s seat and use the seat
belt.
Double cab models

:
DWith rear seat belts—If a child is too
large for a child restraint system, the
child should sit in the rear seat and
must be restrained using the vehicle’s
seat belt. According to accident statis-
tics, the child is safer when properly
restrained in the rear seat than in the
front seat.

: See “Model code” on page vi in the
beginning of this manual if you are not
sure of your vehicle model.
DWithout rear seat belts—We recom-
mend installing the rear seat belts on
your vehicle. Ask any authorized
Toyota dealer or repairer, or another
duly qualified and equipped profession-
al, if rear seat belts can be installed
on your vehicle. If installation is
possible, put the child in the rear seat
and use the seat belts. If installation is
not possible, let the child sit in the
front seat and use the seat belt.
If a child must sit in the front seat, the
seat belts should be worn properly.
Do not allow the child to stand up or
kneel on either rear or front seats. An
unrestrained child could suffer serious in-
jury or death during emergency braking or
a collision. Also, do not let the child sit
on your lap. It does not provide sufficient
restraint.
Pregnant woman.Toyota recommends the
use of a seat belt. Ask your doctor for
specific recommendations. The lap belt
should be worn securely and as low as
possible over the hips and not on the
waist.
Injured person.Toyota recommends the
use of a seat belt. Depending on the inju-
ry, first check with your doctor for specific
recommendations.
If seat belt regulations exist in the country
where you reside, please contact any au-
thorized Toyota dealer or repairer, or
another duly qualified and equipped pro-
fessional, for seat belt replacement or
installation.
Dyna100/150_EE
Seat belts—
—Seat belt precautions

76GAUGES, METERS AND SERVICE REMINDER INDICATORS
While driving on steep inclines or rough
roads which causes the vehicle to sub-
stantially sway or on curves, this light
may come on due to the movement of
engine oil in the engine.
In normal conditions, due to engine oil
consumption, this light may come on earli-
er than the specified service interval of
the scheduled maintenance. This is be-
cause the engine oil is consumed to the
low level within the scheduled mainte-
nance interval and does not indicate a
problem. (For detailed information, see
“Facts about engine oil consumption” on
page 115 in Section 2.)
NOTICE
Continued engine operation with low
engine oil will damage the engine.
(e) Malfunction Indicator Lamp
This lamp comes on in the following
cases.
a. On some models: The fuel tank is
completely empty. (See “Fuel gauge”
on page 68 in this Section for instruc-
tions.)
b. There is a problem somewhere in the
engine electricalsystem, electronic en-
gine control system orengine emission
control system.
If it comes on while you are driving in
case b, have your vehicle checked/re-
paired by any authorized Toyota dealer or
repairer, or another duly qualified and
equipped professional, as soon as pos-
sible.If engine speed does not increase when
the accelerator pedal is depressed, there
may be a problem somewhere in the elec-
tronic engine controlsystem. Stop the ve-
hicle and contact any authorized Toyota
dealer or repairer, or another duly quali-
fied and equipped professional, or take
your vehicle carefully, since the vehicle
performance will be lower than normal, to
any authorized Toyota dealer or repairer,
or another duly qualified and equipped
professional, as soon as possible.
Even if the abnormality in the electronic
engine controlsystem is corrected during
low speed driving, thesystem may not
recover until the engine is stopped and
the engine switch is turned to the “ACC”
or “LOCK” position.
The lamp flashes when the engine emis-
sion control system is not functioning cor-
rectly. If the engine is run for more than
50 hours with the lamp flashing, the sys-
tem will automatically reduce engine per-
formance until the malfunction is cor-
rected.
(f) Low Fuel Level Warning Light
This light comes on when the fuel level
in the tank becomes nearly empty. Fill up
the tank as soon as possible.
On inclines or curves, due to the move-
ment of fuel in the tank, the low fuel level
warning light may come on earlier than
usual.
Dyna100/150_EE

AIR CONDITIONING SYSTEM89
DTo cool off your Toyota after it has
been parked in the hot sun, drive with
the windows open for a few minutes.
This vents the hot air, allowing the air
conditioning to cool the interior more
quickly.
DMake sure the air intake grilles in front
of the windshield are not blocked (by
leaves or snow, for example).
DKeep the area under the front seats
clear to allow air to circulate through-
out the vehicle.
DOn cold days, set the fan speed to
high for a minute to help clear the
intake ducts of snow or moisture. This
can reduce the amount of fogging on
the windows.
DWhen driving on dusty roads, close all
windows. If dust thrown up by the ve-
hicle is still drawn into the vehicle after
closing the windows, it is recommended
that the air intake selector be set to
FRESH and the fan speed selector to
any setting except “OFF”.
DIf following another vehicle on a dusty
road, or driving in windy and dusty
conditions, it is recommended that the
air intake selector be temporarily set to
RECIRCULATE, which will close off the
outside passage and prevent outside
air and dust from entering the vehicle
interior.
DDuring use, various odors from inside
and outside the vehicle may enter into
and accumulate in the air conditioning
system. This may then causeodor to
be emitted from the vents.
DTo reduce potential odors from occur-
ring:
It is recommended that the air condi-
tioning system be set to outside air
mode prior to turning the vehicle off.
CAUTION
To prevent the windshield from fog-
ging up, do not select the windshield
air outlets during cool air operation
in extremely humid weather. The dif-
ference between the temperature of
the outside air and that of the wind-
shield can cause the outer surface of
the windshield to fog up, blocking
your vision.
NOTICE
To prevent battery discharge, do not
leave the air conditioning system on
longer than necessary when the en-
gine is stopped.
Heating
For best results, set controls to:
Fan speed—Any setting except “OFF”
Temperature—To w a r d sWARM
(red zone)
Air intake—FRESH(outside air)
Air flow—FLOOR
Air conditioning—OFF
DFor quick heating, set the temperature
selector lever to the right end position
and select recirculated air mode for a
few minutes. To keep the windows from
fogging after the vehicle interior has
been warmed, select fresh air mode.
DPress the “A/C” button on for dehumidi-
fied heating.
DChoose floor/windshield air flow to heat
the vehicle interior while defrosting the
windshield.
Dyna100/150_EE
Operating tips

OTHER EQUIPMENT105
CAUTION
Observe the following precautions.
Failure to do so may cause the driv-
er ’s floor mat to slip, possibly inter-
fering with the pedals while driving.
An unexpectedly high speed may re-
sult or it may become difficult to
stop the vehicle, leading to a serious
accident.
When installing the driver’s floor mat:
DDo not use floor mats designed for
other models or different model
year vehicles, even if they are
Toyota Genuine floor mats.
DOnly use floor mats designed for
the driver ’s seat.
DDo not use two or more floor mats
on top of each other.
DDo not place the floor mat bottom−
side up or upside−down.
Before driving:
DEnsure that the floor mat has been
placed correctly.
DWith the engine stopped and the
shift lever in neutral, fully depress
each pedal to the floor to make
sure it does not interfere with the
floor mat.
Dyna100/150_EE

INFORMATION BEFORE DRIVING YOUR TOYOTA109
FUEL TYPE
Use only diesel fuel.
EU area:
Your vehicle must use only diesel fuel
conforming to European standard
EN590.
Except EU area:
Your vehicle must use only diesel fuel
that contains 50 ppm or less of sulfur
and has a cetane number of 48 or
higher.
CETANE NUMBER
Select cetane number 48 or higher.
Use of fuel with a cetane number lower
than stated will cause persistent heavy
knocking. If severe, this will lead to en-
gine damage.
If your engine knocks...
If you detect heavy knocking even when
using the recommended fuel, or if you
hear steady knocking while holding a
steady speed on level roads, consult any
authorized Toyota dealer or repairer, or
another duly qualified and equipped pro-
fessional.
However, occasionally, you may notice
light knocking for a short time while accel-
erating or driving up hills. This is normal
and there is no need for concern.FUEL TANK CAPACITY
L (gal., Imp. gal.)
Model

Fuel tank capacity
KDY22160 (15.9, 13.2)
KDY231
KDY25180 (21.1, 17.6)
KDY261

: See “Model code” on page vi in the
beginning of this manual if you are not
sure of your vehicle model.
Dyna100/150_EE

11 6INFORMATION BEFORE DRIVING YOUR TOYOTA
The tandem master cylinder brakesystem
is a hydraulic system with two separate
sub−systems. If either sub−system should
fail, the other will still work. However, the
pedal will be harder to press, and your
stopping distance will increase. Also, the
brake system warning light may come on.
CAUTION
Do not drive your vehicle with only a
single brake system. Have your
brakes fixed immediately.
BRAKE BOOSTER
The brake booster uses engine vacuum to
power−assist the brakes. If the engine
should quit while you are driving, you can
bringthevehicletoastopwithnormal
pedal pressure. There is enough reserved
vacuum for one or two stops—but no
more!
CAUTION
DDo not pump the brake pedal if the
engine stalls. Each push on the
pedal uses up your reserved vacu-
um.
DEven if the power assist is com-
pletely lost, the brakes will still
work. But you will have to push the
pedal hard, much harder than nor-
mal. And your braking distance will
increase.
ANTI−LOCK BRAKE SYSTEM
(with “ABS” warning light)
The anti−lock brake system is designed
to help prevent lock−up of the wheels
during a sudden braking or braking on
slippery road surfaces. This assists in
providing directional stability and steer-
ing performance of the vehicle under
these circumstances.
Effective way to press the ABS brake
pedal:
When the anti−lock brake system func-
tion is in action, you may feel the brake
pedal pulsating and hear a noise. In this
situation, to let the anti−lock brake sys-
tem work for you, just hold the brake
pedal down more firmly. Do not pump
the brake in a panic stop. This will re-
sult in reduced braking performance.
The anti−lock brake system becomes op-
erative after the vehicle has accelerated
to a speed in excess of approximately 10
km/h (6 mph). It stops operating when the
vehicle decelerates to a speed below
approximately 5 km/h (3 mph).
Depressing the brake pedal on slippery
road surfaces such as on a manhole cov-
er, a steel plate at a construction site,
joints in a bridge, etc. on a rainy day
tends to activate the anti−lock brake sys-
tem.
You may hear a click or motor sound from
the area around the front axle for a few
seconds when the engine is started or just
after the vehicle begins to move. This
means that the anti−lock brake system is
in the self−check mode, and does not indi-
cate a malfunction.
Dyna100/150_EE
Brake system

STARTING AND DRIVING135
KDY261 models

mm (in.)
A
375 (14.8)
B400 (15.7)
C370 (14.6)
D540 (21.3)
E170 (6.7)
F200 (7.9)
G220 (8.7)
H240 (9.4)
I400 (15.7)
J365 (14.4)
K535 (21.1)
L615 (24.2)
M670 (26.4)
N835 (32.9)
O2010 (79.1)

: See “Model code” on page vi in the
beginning of this manual if you are not
sure of your vehicle model.
KDY261 models
TOWING BRACKETS
Toyota recommends using a Toyota genu-
ine bracket. Another bracket of matching
quality can also be used.
Dyna100/150_EE

STARTING AND DRIVING139
DMaintain a moderate speed on high-
ways.The faster you drive, the greater
the fuel consumption. By reducing your
speed, you will cut down on fuel con-
sumption.
DKeep the front wheels in proper
alignment.Avoid hitting the curb and
slow down on rough roads. Improper
alignment not only causes faster tire
wear but also puts an extra load on
the engine, which, in turn, wastes fuel.
DKeep the bottom of your vehicle free
from mud, etc.This not only lessens
weight but also helps prevent corro-
sion.
DKeep your vehicle tuned−up and in
top shape.A dirty air cleaner, carbure-
tor out of adjustment, improper valve
clearance, dirty plugs, dirty oil and
grease, brakes not adjusted, etc. all
lower engine performance and contrib-
ute to poor fuel economy. For longer
life of all parts and lower operating
costs, keep all maintenance work on
schedule, and if you often drive under
severe conditions, see that your vehicle
receives more frequent maintenance.
CAUTION
Never turn off the engine to coast
down hills. Your power steering and
brake booster will not function with-
out the engine running. Also, the
emission control system operates
properly only when the engine is run-
ning.
Dyna100/150_EE