2014 TOYOTA DYNA 100/150 air filter

OVERVIEW OF INSTRUMENTS AND CONTROLS3
1. Headlight and turn signal switches
2. Wiper and washer switches
3. DPF (Diesel Particulate Filter) system
manual regeneration switch
(If equipped)
4. Emergency flasher switch
5. Air conditioning controls
6. Rear fog light switch
7. Auxiliary box8. Cup holder
9. Headlight beam level control dial
10. Ashtray
11. Cigarette lighter
12. Heater idle up switch
13. Engine switch
14. Tilt and telescopic steering lock
release lever
Dyna100/150_EE

OVERVIEW OF INSTRUMENTS AND CONTROLS5
1. Card holder
2. Air conditioning controls
3. Emergency flasher switch
4. Heater idle up switch
5. Headlight and turn signal switches
6. Wiper and washer switches
7. Engine switch
8. Tilt and telescopic steering lock
release lever9. Cigarette lighter
10. Headlight beam level control dial
11 . A s h t r a y
12. Auxiliary box
13. Cup holder
14. Rear fog light switch
15. DPF (Diesel Particulate Filter) system
manual regeneration switch
(If equipped)
Dyna100/150_EE

70GAUGES, METERS AND SERVICE REMINDER INDICATORS
This meter displays the odometer and
two trip meters.
1. Odometer—Shows the total distance
the vehicle has been driven.
2. Two trip meters—Show two different
distances independently driven since
the last time each trip meter was set
to zero.
You can use one trip meter to calculate
the fuel economy and the other to
measure the distance on each trip. All
trip meter data is cancelled if the elec-
trical power source is disconnected.
3. Trip meter reset knob—Resets the two
trip meters to zero, and also change
the meter display.
To change the meter display, quickly
push and release the knob. The meter
display changes in the order from the
odometer to trip meter A to trip meter
B, then back to the odometer each
time you push.
To reset the trip meter A to zero, dis-
play the meter A reading, then push
and hold the knob until the meter is
set to zero. The same process can be
applied for resetting the trip meter B.The oil maintenance management sys-
tem (OMMS) is designed to inform you,
by means of a light, of the time to
change the engine oil and oil filter.
ENGINE OIL AND OIL FILTER CHANGE
Change the engine oil and oil filter in
either of the following cases:
DWhen the engine oil change reminder
light is lit.
DWhen the system is repaired.
DWhen the engine oil change reminder
light does not come on even if two
years have passed since the engine
oil was changed.
DWhen the engine oil change reminder
light does not come on even if you
have driven over 30000 km (18000
miles) since the engine oil was
changed.
The lighting timing will change according
to the driving condition.
Because engine oil deteriorates over
time, there are cases when it is neces-
sary to change the engine oil before
the engine oil change reminder light
comes on. In these cases, change the
engine oil and oil filter according to the
maintenance schedule. (For engine oil
maintenance intervals, see the separate
“Toyota Service Booklet” or “Toyota
Warranty Booklet”.)
Dyna100/150_EE
Odometer and two trip
metersOil maintenance management
system

GAUGES, METERS AND SERVICE REMINDER INDICATORS71
ENGINE OIL CHANGE REMINDER LIGHT
This light comes on when the engine
switch is turned to the “ON” position. It
goes out after about 3 seconds. This indi-
cates that the system is functioning nor-
mally. If the light illuminates for 3 seconds
and then flashes for about 12 seconds,
this indicates that the time to change the
engine oil is approaching.
If this light stays on this warns you to
change the engine oil and oil filter us-
ing appropriate replacements at your
earliest convenience. For more informa-
tion about oil grade and viscosity, see
“Checking the engine oil level” on page
188 in Section 7−2.
After changing the engine oil and oil filter,
be sure to reset the system, so that the
light goes out. (For instructions on reset-
ting the system, see “RESETTING THE
SYSTEM” on page 72 in this Section.)
The system must also be reset if an en-
gine oil and oil filter change is performed
before the light comes on. If you do not
reset the system, it cannot inform you of
the correct time to change the engine oil
and oil filter.If any of the following occurs, the
system may not be functioning normal-
ly. Have the vehicle checked at any
authorized Toyota dealer or repairer, or
another duly qualified and equipped
professional.
DWhen the engine switch is turned to
the “ON” position, the light does not
come on.
DThe light flashes.
DAfter changing the engine oil and oil
filter, even though thesystem hasbeen
reset, the light does not go out, or
comes on again soon.
NOTICE
After changing the engine oil and oil
filter, be sure to reset the system.
(For instructions on resetting the sys-
tem, see “RESETTING THE SYSTEM”
on page 72 in this Section.) If you do
not reset the system, it cannot inform
you of the correct time to change the
engine oil and oil filter.
Dyna100/150_EE

GAUGES, METERS AND SERVICE REMINDER INDICATORS77
(g) “ABS” Warning Light
The light comes on when the engine
switch is turned to the “ON” position. If
the anti−lock brake system works properly,
the light turns off after a few seconds.
Thereafter, if the system malfunctions, the
light comes on again.
When the “ABS” warning light is on (and
the brake system warning light is off), the
anti−lock brake systemdoes not operate,
but the brake system stilloperates con-
ventionally.
When the “ABS” warning light is on (and
the brake system warning light is off), the
anti−lock brake systemdoes not operate
so that the wheels could lock up during
a sudden braking or braking on slippery
road surfaces.
If either of the following conditions oc-
curs, this indicates a malfunction some-
where in the components monitored by
the warning light system. Contact any
authorized Toyota dealer or repairer, or
another duly qualified and equipped
professional, as soon as possible to
service the vehicle.
DThe light does not come on when the
engine switch is turned to the “ON”
position, or the light remains on.
DThe light comes on while you are driv-
ing.
A warning light turning on briefly during
operation does not indicate a problem.
(h) SRS Warning Light
This light will come on when the engine
switch is turned to the “ON” position.
After about 6 seconds, the light will go
off. This means the systems of the air-
bag and driver ’s seat belt pretensioner
are operating properly.
This warning light system monitors the
airbag sensor assembly, airbag sensor,
driver ’s seat belt pretensioner assembly,
inflator, interconnecting wiring and power
sources.If either of the following conditions occurs,
this indicates a malfunction somewhere in
the parts monitored by the warning light
system. Contact any authorized Toyota
dealer or repairer, or another duly quali-
fied and equipped professional, as soon
as possible to service the vehicle.
DThe light does not come on when the
engine switch is turned to the “ON”
position or remains on for more than
6 seconds or flashes.
DThe light comes on or starts flashing
while driving.
(i) DPF (Diesel Particulate Filter) Sys-
tem Indicator Light
If the deposit builds up in the filter, the
indicator light on the instrument cluster
will come on when the engine switch is
turned on. The deposit built up in the filter
needs to be regenerated. For details, see
“DPF system” onpage 110 in Section 2.
If you do not perform regeneration and
continue to drive for a while with the indi-
cator light on, the light will begin to flash.
CAUTION
Continuing to drive with the light
flashing will cause the malfunction in-
dicator light to come on. In this
event, damage may be caused to the
vehicle or an accident may occur. If
the malfunction indicator light comes
on, have your vehicle checked by any
authorized Toyota dealer or repairer,
or another duly qualified and
equipped professional immediately.
Dyna100/150_EE

78GAUGES, METERS AND SERVICE REMINDER INDICATORS
(j) Timing Belt Replacement Warning
Light
This light will come on every time when
the trip amount gets between 140000 km
and 150000 km in kilometer reading or
90000 miles in mile reading to indicate
that the timing belt should be replaced.
When it comes on, have the belt replaced
and the warning light reset by any autho-
rized Toyota dealer or repairer, or another
duly qualified and equipped professional.
NOTICE
Continued driving without having the
belt replaced will result in a broken
belt and engine damage.
(k) Fuel Filter Warning Light
The light warns you that the amount of
accumulated water in the fuel filter has
reached the specified level.
If it comes on, drain the water immediate-
ly. (See page 192 in Section 7−2for
instructions for how to drain the water.)
NOTICE
Never drive the vehicle with the warn-
ing light on. Continued driving with
water accumulated in the fuel filter
will damage the fuel injection pump.
(l) Engine Oil Change Reminder Light
This light comes on to remind you to
change the engine oil and oil filter.
If the light comes on, change the engine
oil and oil filter at your earliest conve-
nience. For detailed information, see “Oil
maintenance managementsystem” on
page 70 in this Section.(m) Light Reminder Buzzer
This buzzer will sound if the driver ’s door
is opened while the engine switch is
turned to the “LOCK” position with the
headlight switch on. Removing the key will
not stop the buzzer as long as the head-
light switch is on.
CHECKING SERVICE REMINDER
INDICATORS (except the low fuel level
warning light)
1. Apply the parking brake.
2. Turn the engine switch to the “ACC”
position.
The SRS warning light should come on.
It goes off after about 6 seconds.
3. Turn the engine switch to the “ON”
position, but do not start the engine.
All the service reminder indicators ex-
cept the SRS warning light should
come on. The “ABS” warning light goes
off after a few seconds. The engine oil
change reminder light goes off after
about 5 seconds.
If any service reminder indicator or warn-
ing buzzer does not function as described
above, have it checked by any authorized
Toyota dealer or repairer, or another duly
qualified and equipped professional, as
soon as possible.
Dyna100/150_EE

AIR CONDITIONING SYSTEM83
Section 1−7
OPERATION OF INSTRUMENTS AND
CONTROLS
Air conditioning system
DControls 84...........................................
DAir flow selector settings 88............................
DOperating tips 89......................................
DSide vents 91.........................................
DRear heatersystem 92.................................
DHeater idle up switch 93................................
DAir conditioning filters 93...............................
Dyna100/150_EE

AIR CONDITIONING SYSTEM93
Push the switch to increase engine
speed. Push the switch once again to
return the engine to the normal idle
speed.
Use the heater idle up switch to boost the
heating effect in extremely cold conditions
when the vehicle is not moving.
When the engine coolant is hot (normal
operating temperature), thesystem may
not operate.Outside filter
Inside filter
There are both inside and outside air
conditioning filter. The filters are on the
passenger ’s side. Refer to theillustra-
tions above.
The filters may become clogged after
long use. If the operating efficiency of
the heater becomes poor, or if the win-
dows begin to fog up easily, the filters
may need to be cleaned.
Dyna100/150_EE
Heater idle up switch Air conditioning filters—