2014 NISSAN TEANA Pressure

EC-610
< SYSTEM DESCRIPTION >[VQ35DE]
DIAGNOSIS SYSTEM (ECM)
*: This function is not necessary in the usual service procedure.
ACTIVE TEST MODE
Test Item
WORK ITEM CONDITION USAGE
IDLE AIR VOL LEARN The idle air volume that keeps the engine within the specified range is memorized in ecm. When learning the idle air volume
EVAP SYSTEM CLOSE Close the EVAP canister vent control valve in order to make
EVAP system close under the following conditions.
• Ignition switch ON
• Engine not running
• Ambient temperature is above 0 °C (32 °F).
• No vacuum and no high pressure in EVAP system
• Fuel tank temperature is more than 0 °C (32 °F).
• Within 10 minutes after starting “EVAP SYSTEM CLOSE”
• When trying to execute “EVAP SYSTEM CLOSE” under
the condition except above, CONSULT will discontinue it
and display appropriate instruction.
NOTE:
When starting engine, CONSULT may display “BAT-
TERY VOLTAGE IS LOW. CHARGE BATTERY”, even in
using charged battery. When detecting EVAP vapor leak-
age in the EVAP system
FUEL PRESSURE RELEASE Fuel pu mp will stop by touching “START” during idling.
crank a few times after engine stalls. When releasing fuel pressure from
fuel line
SELF-LEARNING CONT The coefficient of self-learning control mixture ratio returns to the original coefficient. When clearing mixture ratio self-
learning value
TARGET IGN TIM ADJ* Idle condition When adjusting target ignition tim- ing
TARGET IDLE RPM ADJ* Idle condition When setting target idle speed
VIN REGISTRATION In this mode, VIN is registered in ECM When registering VIN in ECM
CLSD THL POS LEARN Ignition on and engine stopped. When learning the throttle valve
closed position
SAVING DATA FOR REPLC CPU In this mode, save data that is in ECM. When ECM replaced.
WRITING DATA FOR REPLC CPU In this mode, write data stored by “SAVING DATA FOR RE-
PLC CPU” in work support mode to ECM. When ECM replaced.
TEST ITEM CONDITION JUDGMENT CHECK ITEM (REMEDY)
FUEL INJEC-
TION • Engine: Return to the original
non-standard condition
• Change the amount of fuel injec- tion using CONSULT. If malfunctioning symptom disap-
pears, see CHECK ITEM. • Harness and connectors
• Fuel injector
• Air fuel ratio (A/F) sensor 1
ENG COOLANT
TEMP • Engine: Return to the original
non-standard condition
• Change the engine coolant tem- perature using CONSULT. If malfunctioning symptom disap-
pears, see CHECK ITEM. • Harness and connectors
• Engine coolant temperature sen-
sor
• Fuel injector
PURG VOL
CONT/V • Engine: After warming up, run en-
gine at 1,500 rpm.
• Change the EVAP canister purge volume control solenoid valve
opening percent using CON-
SULT. Engine speed changes according to
the opening percent. • Harness and connectors
• Solenoid valve
FUEL/T TEMP
SEN • Change the fuel tank temperature using CONSULT.
ALTERNATOR
DUTY •Engine: Idle
• Change duty ratio using CON-
SULT. Battery voltage changes.
• Harness and connectors
• IPDM E/R
•Alternator
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

ECM
EC-619
< ECU DIAGNOSIS INFORMATION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
3
(SB) 128
(GR) A/F sensor 1 heater (bank 2) Output [Engine is running]
• Warm-up condition
• Idle speed (More than 140 seconds after
starting engine) 2.9 - 8.8 V
4
(LG) 107
(P) Engine oil pressure sensor Input [Engine is running]
• Warm-up condition
• Idle speed 1.3 V
[Engine is running]
• Warm-up condition
• Engine speed is 2,000 rpm 2.7 V
5
(P) 128
(GR) Throttle control motor (Open) Output [Ignition switch: ON]
• Engine stopped
• Selector lever: D position
• Accelerator pedal: Fully de-
pressed 0 - 14 V
[Ignition switch: ON]
• Engine stopped
• Selector lever: D position
• Accelerator pedal: Fully re- leased 0 - 14 V
6
(BR) 128
(GR) A/F sensor 1 heater
(bank 1) Output[Engine is running]
• Warm-up condition
• Idle speed
(More than 140 seconds after
starting engine) 2.9 - 8.8 V
Terminal No. Description
ConditionVa l u e
(Approx.)
+ -– Signal name Input/
Output
JMBIA0030GB
JPBIA3359ZZ
JPBIA3360ZZ
JMBIA0031GB
JMBIA0032GB
JMBIA0902GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

ECM
EC-623
< ECU DIAGNOSIS INFORMATION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
56
(BR) 128
(GR) Intake valve timing control so-
lenoid valve (bank 2) Output[Engine is running]
• Warm-up condition
• Idle speed BATTERY VOLTAGE
(11 - 14 V)
[Engine is running]
• Warm-up condition
• Engine speed: 2,000 rpm 7 - 12 V
57
(L) 128
(GR) Heated oxygen sensor 2
(bank 1) Input[Engine is running]
Revving engine from idle to
3,000 rpm quickly after the fol-
lowing conditions are met
• Engine: after warming up
• Keeping the engine speed be- tween 3,500 and 4,000 rpm
for 1 minute and at idle for 1
minute under no load 0 - 1.0 V
58
(L) 128
(GR) Heated oxygen sensor 2
(bank 2) Input[Engine is running]
Revving engine from idle to
3,000 rpm quickly after the fol-
lowing conditions are met
• Engine: after warming up
• Keeping the engine speed be-
tween 3,500 and 4,000 rpm
for 1 minute and at idle for 1
minute under no load 0 - 1.0 V
59
(L) —Sensor ground
(Heated oxygen sensor 2) —— —
63
(W) 64
(P) Refrigerant pressure sensor Input [Engine is running]
• Warm-up condition
• Both A/C switch and blower
fan motor switch: ON (Com-
pressor operates) 1.0 - 4.0 V
64
(P) —Sensor ground
(Refrigerant pressure sensor) —— —
66
(G) 68
(R) Battery current sensor Input [Engine is running]
• Battery: Fully charged*
2
• Idle speed 2.6 - 3.5 V
67
(W) 68
(R) Battery temperature sensor Input [Engine is running] 0 - 4.8 V
Output voltage varies with battery temperature.
68
(R) —Sensor ground
(Battery curre nt sensor) —— —
69
(W) 128
(GR) A/F sensor 1 (bank 1) Input [Engine is running]
• Warm-up condition
• Engine speed: 2,000 rpm 2.2 V
Output voltage varies with air fuel ratio.
70
(BR) 76
(B) Engine coolant temperature
sensor Input [Engine is running] 0 - 4.8 V
Output voltage varies with engine
coolant temperature.
73
(B) 128
(GR) A/F sensor 1 (bank 1) Input [Ignition switch: ON] 1.8 V
Terminal No. Description
ConditionVa l u e
(Approx.)
+ -– Signal name Input/
Output
JMBIA0038GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-626
< ECU DIAGNOSIS INFORMATION >[VQ35DE]
ECM
96
(R) 64
(P) Sensor power supply
(Refrigerant pressure sensor) — [Ignition switch: ON] 5 V
97
(W) 100
(O) Accelerator pedal position
sensor 1 Input[Ignition switch: ON]
• Engine stopped
• Accelerator pedal: Fully re-
leased 0.5 - 1.0 V
[Ignition switch: ON]
• Engine stopped
• Accelerator pedal: Fully de-
pressed 4.2 - 4.8 V
98
(P) 11 6
(G) Accelerator pedal position
sensor 2 Input[Ignition switch: ON]
• Engine stopped
• Accelerator pedal: Fully re-
leased 0.25 - 0.50 V
[Ignition switch: ON]
• Engine stopped
• Accelerator pedal: Fully de-
pressed 2.0 - 2.5 V
99
(R) 100
(O) Sensor power supply
(Accelerator pedal position
sensor 1) — [Ignition switch: ON] 5 V
100 (O) —Sensor ground
(Accelerator pedal position
sensor 1) —— —
101 (O) 108
(R) ASCD steering switch Input [Ignition switch: ON]
ASCD steering switch: OFF 4 V
[Ignition switch: ON]
MAIN switch: Pressed 0 V
[Ignition switch: ON]
CANCEL switch: Pressed 1 V
[Ignition switch: ON]
RESUME/ACCELERATE
switch: Pressed 3 V
[Ignition switch: ON]
SET/COAST switch: Pressed 2 V
102 (G) 11 2
(R) EVAP control system pres-
sure sensor Input [Ignition switch: ON] 1.8 - 4.8 V
103 (G) 11 6
(G) Sensor power supply
(Accelerator pedal position
sensor 2) — [Ignition switch: ON] 5 V
104 (P) — Data link connector
Input/
Output ——
106 (Y) 128
(GR) EVAP canister vent control
valve Output [Ignition switch: ON] BATTERY VOLTAGE
(11 - 14 V)
107 (P) 11 2
(R) Sensor power supply
(EVAP control system pres-
sure sensor, engine oil pres-
sure sensor) — [Ignition switch: ON] 5 V
108 (R) —Sensor ground
(ASCD steering switch) —— —
109 (L) 128
(GR) Ignition switch Input [Ignition switch: OFF] 0 V
[Ignition switch: ON] BATTERY VOLTAGE
(11 - 14 V)
Terminal No. Description
ConditionVa l u e
(Approx.)
+ -– Signal name Input/
Output
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-628
< ECU DIAGNOSIS INFORMATION >[VQ35DE]
ECM
DTC RELATED ITEM
Engine operating condi-
tion in fail-safe mode Detected items Remarks
Reference
page
Engine speed will not
rise more than 2,500 rpm
due to the fuel cut Malfunction indicator
lamp circuit When there is an open circuit on MIL circuit, the ECM cannot warn the
driver by illuminating MIL when there is malfunction on engine control
system.
Therefore, when electrical controlled throttle and part of ECM related
diagnoses are continuously detected as NG for 5 trips, ECM warns the
driver that engine control system malfunctions and MIL circuit is open
by means of operating the fail-safe function.
The fail-safe function also operates when above diagnoses except MIL
circuit are detected and demands the driver to repair the malfunction. EC-973
DTC No. Detected items Engine operating condition in fail-safe mode
P0011
P0021 Intake valve timing control The signal is not energized to the intake valve timing control solenoid valve and the valve
control does not function.
P0101
P0102
P0103 Mass air flow sensor circuit Engine speed will not rise more than 2,400 rpm due to the fuel cut.
P0117
P0118 Engine coolant tempera-
ture sensor circuit Engine coolant temperature will be determined by ECM based on the following condition.
CONSULT displays the engine coolant temperature decided by ECM.
Condition Engine coolant temperature decided
(CONSULT display)
Just as ignition switch is turned ON
or START 40
°C (104 °F)
Approx 4 minutes or more after en-
gine starting 80
°C (176 °F)
Except as shown above 40 - 80
°C (104 - 176 °F)
(Depends on the time)
When the fail-safe system for engine coolant temperature sensor is activated, the cooling
fan operates while engine is running.
P0122
P0123
P0222
P0223
P2135 Throttle position sensor The ECM controls the electric throttle control actuator in regulating the throttle opening in
order for the idle position to be within +10 degrees.
The ECM regulates the opening speed of the throttle valve to be slower than the normal
condition.
Therefore, the acceleration will be poor.
P0196
P0197
P0198 Engine oil temperature
sensor Intake valve timing control does not function.
P0500 Vehicle speed sensor The cooling fan operates (Highest) while engine is running.
P0524 Engine oil pressure • ECM illuminates oil pressure warning lamp on the combination meter.
• Engine speed will not rise more than 4,000 rpm due to the fuel cut.
• Fail-safe is canceled when ignition switch OFF → ON.
P0605 ECM (When ECM calculation function is malfunctioning:) ECM stops the electric throttle control actuator control, throttle valve is maintained at a
fixed opening (approx. 5 degrees) by the return spring.
ECM deactivates ASCD operation.
P0643 Sensor power supply ECM stops the electric throttle control actuator control, throttle valve is maintained at a fixed opening (approx. 5 degrees) by the return spring.
P1805 Brake switch ECM controls the electric throttle control actuator by regulating the throttle opening to a small range.
Therefore, acceleration will be poor.
Vehicle condition Driving condition
When engine is idling Normal
When accelerating Poor acceleration
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-630
< ECU DIAGNOSIS INFORMATION >[VQ35DE]
ECM
DTC Index
INFOID:0000000009462545
× :Applicable —: Not applicable
2 P0031, P0032, P0051, P0052 Air fuel ratio (A/F) sensor 1 heater
P0037, P0038, P0057, P0058 Heated oxygen sensor 2 heater
P0075, P0081 Intake valve timing control solenoid valve
P0130, P0131, P0132, P014 C, P014D, P014E, P014F,
P0150, P0151, P0152, P209 6, P2097, P2098, P2099 Air fuel ratio (A/F) sensor 1
P0137, P0138, P0139, P0157, P0158, P0159 Heated oxygen sensor 2
P0441 EVAP control system purge flow monitoring
P0443, P0444, P0445 EVAP canister purge volume control solenoid valve
P0447, P0448 EVAP canister vent control valve
P0451, P0452, P0453 EVAP control system pressure sensor
P0603 ECM power supply
P1217 Engine over temperature (OVERHEAT)
P1800, P1801 VIAS cont rol solenoid valve
P1805 Brake switch
P2100, P2103 Throttle control motor relay
P2101 Electric throttle control function
P2118 Throttle control motor
3 P0011, P0021 Intake valve timing control P0171, P0172, P0174, P0175 Fuel injection system function
P0300 - P0306 Misfire
P0420, P0430 Three way catalyst function
P0456 EVAP control syst em (VERY SMALL LEAK)
P0506, P0507 Idle speed control system
P050A, P050E Cold start control
P0524 Engine oil pressure
P1148, P1168 Closed loop control
P1212 TCS communication line
P1564 ASCD steering switch
P1572 Brake pedal position switch
P1574 ASCD vehicle speed sensor
P2119 Electric throttle control actuator
Priority Detected items (DTC) Detected items (DTC)
DTC*1
Items
(CONSULT screen terms) SRT
code Trip MIL Permanent
DTC group*4Refer-
ence page
CONSULT
GST
*2ECM*3
U0101 0101*5LOST COMM (ECM) — 1 ×BEC-713
U1001
1001*5CAN COMM CIRCUIT — 2 — — EC-714
P0000 0000NO DTC IS DETECTED.
FURTHER TESTING
MAY BE REQUIRED. ——
Blinking*6——
P0011 0011 INT/V TIM CONT-B1 ×2 ×BEC-715
P0021 0021 INT/V TIM CONT-B2 ×2 ×BEC-715
P0031 0031 A/F SEN1 HTR (B1) — 2 ×BEC-719
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

ECM
EC-633
< ECU DIAGNOSIS INFORMATION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
OP0463 0463 FUEL LEVL SEN/CIRC — 2
×BEC-866
P0500 0500
VEH SPEED SEN/CIRC*8—2×BEC-867
P0506 0506 ISC SYSTEM — 2 ×BEC-869
P0507 0507 ISC SYSTEM — 2 ×BEC-871
P050A 050A COLD START CONTROL — 2 ×AEC-873
P050E 050E COLD START CONTROL — 2 ×AEC-873
P0520 0520 EOP SENSOR/SWITCH — 2 — — EC-875
P0524 0524 ENGINE OIL PRESSURE — 1 — —EC-878
P0603 0603 ECM BACK UP/CIRCUIT — 2×BEC-881
P0605 0605 ECM — 1 or 2 × or — B EC-883
P0607 0607 ECM — 1 ×BEC-884
P0643 0643 SENSOR POWER/CIRC — 1 ×BEC-885
P0850 0850 P-N POS SW/CIRCUIT — 2 ×BEC-887
P1148 1148 CLOSED LOOP-B1 — 1 ×AEC-890
P1168 1168 CLOSED LOOP-B2 — 1 ×AEC-890
P1212 1212 TCS/CIRC — 2 — — EC-891
P1217 1217 ENG OVER TEMP — 1×BEC-892
P1225 1225 CTP LEARNING-B1 — 2 — — EC-895
P1226 1226 CTP LEARNING-B1 — 2 — —EC-896
P1550 1550 BAT CURRENT SENSOR — 2 — —EC-897
P1551 1551 BAT CURRENT SENSOR — 2 — —EC-899
P1552 1552 BAT CURRENT SENSOR — 2 — —EC-899
P1553 1553 BAT CURRENT SENSOR — 2 — —EC-901
P1554 1554 BAT CURRENT SENSOR — 2 — —EC-903
P1556 1556 BAT TMP SEN/CIRC — 2 — —EC-906
P1557 1557 BAT TMP SEN/CIRC — 2 — —EC-906
P1564 1564 ASCD SW — 1 — —EC-908
P1572 1572 ASCD BRAKE SW — 1 — — EC-911
P1574 1574 ASCD VHL SPD SEN — 1 — —EC-918
P1610 1610 LOCK MODE — 2 — —SEC-68
P1611 1611 ID DISCORD, IMM-ECM — 2 — —SEC-69
P1612 1612 CHAIN OF ECM-IMMU — 2 — — SEC-70
P1614 1614 CHAIN OF IMMU-KEY — 2 — —SEC-71
P1800 1800 VIAS S/V-1 — 2 — — EC-920
P1801 1801 VIAS S/V-2 — 2 — —EC-922
P1805 1805 BRAKE SW/CIRCUIT — 2 — —EC-924
P2096 2096 A/F SENSOR1 (B1) — 2×AEC-927
P2097 2097 A/F SENSOR1 (B1) — 2 ×AEC-927
P2098 2098 A/F SENSOR1 (B2) — 2 ×AEC-927
P2099 2099 A/F SENSOR1 (B2) — 2 ×AEC-927
P2100 2100 ETC MOT PWR-B1 — 1 ×BEC-931
P2101 2101 ETC FNCTN/CIRC-B1 — 1 ×BEC-933
DTC*1
Items
(CONSULT screen terms) SRT
code Trip MIL Permanent
DTC group*4Refer-
ence page
CONSULT
GST
*2ECM*3
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-638
< ECU DIAGNOSIS INFORMATION >[VQ35DE]
ECM
VVT
SYSTEM 35H VVT Monitor (Bank1)
P0011 80H 9DH
VTC intake function diagnosis (VTC
alignment check diagnosis)
P0014 81H 9DH VTC exhaust function diagnosis (VTC
alignment check diagnosis)
P0011 82H 9DH VTC intake function diagnosis (VTC
drive failure diagnosis)
P0014 83H 9DH VTC exhaust function diagnosis (VTC
drive failure diagnosis)
P100A 84H 10H VEL slow response diagnosis P1090 85H 10H VEL servo system diagnosis
P0011 86H 9DH VTC intake intermediate lock function
diagnosis (VTC intermediate position
alignment check diagnosis)
Advanced: P052A Retarded: P052B 87H 9DHVTC intake intermediate lock system
diagnosis (VTC intermediate lock posi-
tion check diagnosis)
36H VVT Monitor (Bank2) P0021 80H 9DH
VTC intake function diagnosis (VTC
alignment check diagnosis)
P0024 81H 9DH VTC exhaust function diagnosis (VTC
alignment check diagnosis)
P0021 82H 9DH VTC intake function diagnosis (VTC
drive failure diagnosis)
P0024 83H 9DH VTC exhaust function diagnosis (VTC
drive failure diagnosis)
P100B 84H 10H VEL slow response diagnosis P1093 85H 10H VEL servo system diagnosis
P0021 86H 9DH VTC intake intermediate lock function
diagnosis (VTC intermediate position
alignment check diagnosis)
Advanced: P052C Retarded: P052D 87H 9DHVTC intake intermediate lock system
diagnosis (VTC intermediate lock posi-
tion check diagnosis)
EVAP
SYSTEM 39H
EVAP control system leak
(Cap Off) P0455 80H 0CHDifference in pressure sensor output
voltage before and after pull down
3BH EVAP control system leak
(Small leak) P0442 80H 05H
Leak area index (for more than 0.04
inch)
3CH EVAP control system leak
(Very small leak) P0456 80H 05H
Leak area index (for more than 0.02
inch)
P0456 81H FDH Maximum internal pressure of EVAP
system during monitoring
P0456 82H FDH Internal pressure of EVAP system at
the end of monitoring
3DH Purge flow system P0441 83H 0CH Difference in pressure sensor output
voltage before and after vent control
valve close
Item
OBD-
MID Self-diagnostic test item DTC Test value and Test
limit
(GST display) Description
TID Unit and
Scaling ID
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM