2014 NISSAN TEANA engine oil

DIAGNOSIS SYSTEM (ECM)EC-611
< SYSTEM DESCRIPTION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
*: Leaving cooling fan OFF with CONSULT while engine is running may cause the engine to overheat.
DTC WORK SUPPORT MODE
Test Item
FUEL PUMP RE-
LAY • Ignition switch: ON (Engine
stopped)
• Turn the fuel pump relay “ON” and “OFF” using CONSULT and
listen to operating sound. Fuel pump relay makes the operat-
ing sound. • Harness and connectors
• Fuel pump relay
VIAS S/V-1 • Ignition switch: ON
• Turn solenoid valve “ON” and “OFF” using CONSULT and listen
to operating sound. Solenoid valve makes the operating
sound. • Harness and connectors
• Solenoid valve
ENGINE
MOUNTING • Ignition switch: ON
• Turn electronic controlled engine mount “IDLE” and “TRVL” with
CONSULT. Electronic controlled engine mount
makes the operating sound. • Harness and connectors
• Electronic controlled engine mount
VIAS S/V-2 • Ignition switch: ON
• Turn solenoid valve “ON” and “OFF” using CONSULT and listen
to operating sound. Solenoid valve makes the operating
sound. • Harness and connectors
• Solenoid valve
IGNITION TIM-
ING • Engine: Return to the original
non-standard condition
• Timing light: Set
• Retard the ignition timing using
CONSULT. If malfunctioning symptom disap-
pears, see CHECK ITEM. Perform Idle Air Volume Learning.
POWER BAL-
ANCE • Engine: After warming up, idle the
engine.
• A/C switch OFF
• Selector lever: P or N position
• Cut off each injector signal one at a time using CONSULT. Engine runs rough or stops. • Harness and connectors
• Compression
• Fuel injector
• Power transistor
•Spark plug
• Ignition coil
VENT CON-
TROL/V • Ignition switch: ON (Engine
stopped)
• Turn solenoid valve “ON” and “OFF” with the CONSULT and lis-
ten to operating sound. Solenoid valve makes an operating
sound. • Harness and connectors
• Solenoid valve
V/T ASSIGN AN-
GLE • Engine: Return to the original
non-standard condition
• Change intake valve timing using
CONSULT. If malfunctioning symptom disap-
pears, see CHECK ITEM. • Harness and connectors
• Intake valve timing control sole- noid valve
COOLING FAN* • Ignition switch: ON
• Turn the cooling fan “HI”, “MID”, “LOW” and “OFF” using CON-
SULT. Cooling fan moves and stops.
• Harness and connectors
• Cooling fan motor
•IPDM E/R
TEST ITEM CONDITION JUDGMENT CHECK ITEM (REMEDY)
Test mode Test item Corresponding DTC No. Reference page
A/F SEN1 A/F SEN1(B1) P1276 P0130
EC-753
A/F SEN1(B2) P1286 P0150EC-753
EVAPORATIVE SYSTEMPURG FLOW P0441 P0441
EC-828PURG VOL CN/V P1444 P0443EC-833
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-616
< ECU DIAGNOSIS INFORMATION >[VQ35DE]
ECM
HO2S2 HTR (B2)Engine speed: Below 3,600 rpm after the following conditions are met.
• Engine: After warming up
• Keeping the engine speed between 3,500 and 4,000 rpm for 1 minute and at idle for 1 minute under no load On
Engine speed: Above 3,600 rpm Off
ALT DUTY SIG Power generation voltage variable control: Operating On
Power generation voltage variable control: Not operating Off
I/P PULLY SPD Vehicle speed: More than 20 km/h (12 MPH) Almost the same speed as
the tachometer indication
VEHICLE SPEED Turn drive wheels and compare CONSULT value with the speedometer indica-
tion. Almost the same speed as
the speedometer indication
IDL A/V LEARN Engine: Running Idle air volume learning has not been per-
formed yet. YET
Idle air volume learning has already been
performed successfully. CMPLT
TRVL AFTER MIL Ignition switch: ON Vehicle has traveled after MIL has illumi-
nated. 0 - 65,535 km
(0 - 40,723 miles)
ENG OIL TEMP Engine: After warming up More than 70 °C (158 °F)
VHCL SPEED SE Turn drive wheels and compare CONSULT value with the speedometer indica-
tion. Almost the same speed as
the speedometer indication
SET VHCL SPD Engine: Running ASCD: Operating The preset vehicle speed is
displayed
MAIN SW Ignition switch: ON MAIN switch: Pressed On
MAIN switch: Released Off
CANCEL SW Ignition switch: ON CANCEL switch: Pressed On
CANCEL switch: Released Off
RESUME/ACC SW Ignition switch: ON RESUME/ACCELERATE switch:
Pressed On
RESUME/ACCELERATE switch: Re-
leased Off
SET SW Ignition switch: ON SET/COAST switch: Pressed On
SET/COAST switch: Released Off
BRAKE SW1
(Brake pedal posi-
tion switch) Ignition switch: ON Brake pedal: Fully released On
Brake pedal: Slightly depressed Off
BRAKE SW2
(Stop lamp switch) Ignition switch: ON Brake pedal: Fully released Off
Brake pedal: Slightly depressed On
VHCL SPD CUT Ignition switch: ON Non
LO SPEED CUT Ignition switch: ON Non
AT OD MONITOR Ignition switch: ON Off
AT OD CANCEL Ignition switch: ON Off
CRUISE LAMP Ignition switch: ON MAIN switch: Pressed at the 1st time
→
at the 2nd time On
→ Off
SET LAMP • MAIN switch: ON
• When vehicle speed is between 40 km/h (25 MPH) and 144 km/h
(89 MPH) ASCD: Operating On
ASCD: Not operating Off
ALT DUTY Engine: Idle 0 - 80%
Monitor Item Condition Values/Status
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

ECM
EC-619
< ECU DIAGNOSIS INFORMATION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
3
(SB) 128
(GR) A/F sensor 1 heater (bank 2) Output [Engine is running]
• Warm-up condition
• Idle speed (More than 140 seconds after
starting engine) 2.9 - 8.8 V
4
(LG) 107
(P) Engine oil pressure sensor Input [Engine is running]
• Warm-up condition
• Idle speed 1.3 V
[Engine is running]
• Warm-up condition
• Engine speed is 2,000 rpm 2.7 V
5
(P) 128
(GR) Throttle control motor (Open) Output [Ignition switch: ON]
• Engine stopped
• Selector lever: D position
• Accelerator pedal: Fully de-
pressed 0 - 14 V
[Ignition switch: ON]
• Engine stopped
• Selector lever: D position
• Accelerator pedal: Fully re- leased 0 - 14 V
6
(BR) 128
(GR) A/F sensor 1 heater
(bank 1) Output[Engine is running]
• Warm-up condition
• Idle speed
(More than 140 seconds after
starting engine) 2.9 - 8.8 V
Terminal No. Description
ConditionVa l u e
(Approx.)
+ -– Signal name Input/
Output
JMBIA0030GB
JPBIA3359ZZ
JPBIA3360ZZ
JMBIA0031GB
JMBIA0032GB
JMBIA0902GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-624
< ECU DIAGNOSIS INFORMATION >[VQ35DE]
ECM
74
(V) 80
(BR) Intake air temperature sensor Input [Engine is running] 0 - 4.8 V
Output voltage varies with intake air temperature.
75
(O) 68
(R) Sensor power supply
(Battery current sensor) — [Ignition switch: ON] 5 V
76
(B) —Sensor ground
(Engine coolant temperature
sensor, engine oil tempera-
ture sensor) —— —
77
(W) 128
(GR) A/F sensor 1 (bank 2) Input [Engine is running]
• Warm-up condition
• Engine speed: 2,000 rpm 2.2 V
Output voltage varies with air fuel ratio.
78
(G) 76
(B) Engine oil temperature sensor Input [Engine is running] 0 - 4.8 V
Output voltage varies with engine
oil temperature.
80
(BR) —Sensor ground
(Mass air flow sensor, intake
air temperature sensor) —— —
81
(B) 128
(GR) A/F sensor 1 (bank 2) Input [Ignition switch: ON] 1.8 V
82
(P) 80
(BR) Mass air flow sensor Input [Engine is running]
• Warm-up condition
• Idle speed 0.9 - 1.2 V
[Engine is running]
• Warm-up condition
• Engine speed: 2,500 rpm 1.6 - 1.9 V
83
(V) 88
(SB) Sensor power supply
[Camshaft position sensor
(PHASE) (bank 1)] — [Ignition switch: ON] 5 V
84
(SB) —Sensor ground
[Crankshaft position sensor
(POS)] —— —
85
(B) 91
(B) Knock sensor (bank 1) Input [Engine is running]
Idle speed 2.5 V*
1
86
(W) 91
(B) Knock sensor (bank 2) Input [Engine is running]
Idle speed 2.5 V*1
87
(V) 92
(SB) Sensor power supply
[Camshaft position sensor
(PHASE) (bank 2)] — [Ignition switch: ON] 5 V
88
(SB) —Sensor ground
[Camshaft position sensor
(PHASE) (bank 1)] —— —
Terminal No. Description
ConditionVa l u e
(Approx.)
+ -– Signal name Input/
Output
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-626
< ECU DIAGNOSIS INFORMATION >[VQ35DE]
ECM
96
(R) 64
(P) Sensor power supply
(Refrigerant pressure sensor) — [Ignition switch: ON] 5 V
97
(W) 100
(O) Accelerator pedal position
sensor 1 Input[Ignition switch: ON]
• Engine stopped
• Accelerator pedal: Fully re-
leased 0.5 - 1.0 V
[Ignition switch: ON]
• Engine stopped
• Accelerator pedal: Fully de-
pressed 4.2 - 4.8 V
98
(P) 11 6
(G) Accelerator pedal position
sensor 2 Input[Ignition switch: ON]
• Engine stopped
• Accelerator pedal: Fully re-
leased 0.25 - 0.50 V
[Ignition switch: ON]
• Engine stopped
• Accelerator pedal: Fully de-
pressed 2.0 - 2.5 V
99
(R) 100
(O) Sensor power supply
(Accelerator pedal position
sensor 1) — [Ignition switch: ON] 5 V
100 (O) —Sensor ground
(Accelerator pedal position
sensor 1) —— —
101 (O) 108
(R) ASCD steering switch Input [Ignition switch: ON]
ASCD steering switch: OFF 4 V
[Ignition switch: ON]
MAIN switch: Pressed 0 V
[Ignition switch: ON]
CANCEL switch: Pressed 1 V
[Ignition switch: ON]
RESUME/ACCELERATE
switch: Pressed 3 V
[Ignition switch: ON]
SET/COAST switch: Pressed 2 V
102 (G) 11 2
(R) EVAP control system pres-
sure sensor Input [Ignition switch: ON] 1.8 - 4.8 V
103 (G) 11 6
(G) Sensor power supply
(Accelerator pedal position
sensor 2) — [Ignition switch: ON] 5 V
104 (P) — Data link connector
Input/
Output ——
106 (Y) 128
(GR) EVAP canister vent control
valve Output [Ignition switch: ON] BATTERY VOLTAGE
(11 - 14 V)
107 (P) 11 2
(R) Sensor power supply
(EVAP control system pres-
sure sensor, engine oil pres-
sure sensor) — [Ignition switch: ON] 5 V
108 (R) —Sensor ground
(ASCD steering switch) —— —
109 (L) 128
(GR) Ignition switch Input [Ignition switch: OFF] 0 V
[Ignition switch: ON] BATTERY VOLTAGE
(11 - 14 V)
Terminal No. Description
ConditionVa l u e
(Approx.)
+ -– Signal name Input/
Output
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

ECM
EC-627
< ECU DIAGNOSIS INFORMATION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
: Average voltage for pulse signal (Actual pulse signal can be confirmed by oscilloscope.)
*1: This may vary depending on internal resistance of the tester.
*2: Before measuring the terminal voltage, confi rm that the battery is fully charged. Refer to PG-4, "How to
Handle Battery".
Fail-safeINFOID:0000000009462543
NON DTC RELATED ITEM
111
(O) 120
(SB) Fuel tank temperature sensor Input [Engine is running] 0 - 4.8 V
Output voltage varies with fuel tank temperature.
11 2 (R) —Sensor ground
(EVAP control system pres-
sure sensor, engine oil pres-
sure sensor) —— —
11 3 (P) —CAN communication line
(CAN-L) Input/
Output ——
11 4 (L) —CAN communication line
(CAN-H) Input/
Output ——
11 6 (G) —Sensor ground
(Accelerator pedal position
sensor 2) —— —
11 8
(W) 128
(GR) PNP signal Input [Ignition switch: ON]
Selector lever: P or N position BATTERY VOLTAGE
(11 - 14 V)
[Ignition switch: ON]
Selector lever: Except above
position 0 V
120
(SB) —Sensor ground
(Fuel tank temperature sen-
sor) —— —
121
(LG) 128
(GR) Power supply for ECM Input [Ignition switch: ON] BATTERY VOLTAGE
(11 - 14 V)
122 (L) 128
(GR) Stop lamp switch Input [Ignition switch: OFF]
Brake pedal: Fully released 0 V
[Ignition switch: OFF]
Brake pedal: Slightly depressed BATTERY VOLTAGE
(11 - 14 V)
123
(GR)
124
(GR) — ECM ground — — —
126
(BR) 128
(GR) Brake pedal position switch Input [Ignition switch: ON]
Brake pedal: Slightly depressed 0 V
[Ignition switch: ON]
Brake pedal: Fully released BATTERY VOLTAGE
(11 - 14 V)
127
(GR) 128
(GR) — ECM ground — — —
Terminal No. Description
ConditionVa l u e
(Approx.)
+ -– Signal name Input/
Output
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-628
< ECU DIAGNOSIS INFORMATION >[VQ35DE]
ECM
DTC RELATED ITEM
Engine operating condi-
tion in fail-safe mode Detected items Remarks
Reference
page
Engine speed will not
rise more than 2,500 rpm
due to the fuel cut Malfunction indicator
lamp circuit When there is an open circuit on MIL circuit, the ECM cannot warn the
driver by illuminating MIL when there is malfunction on engine control
system.
Therefore, when electrical controlled throttle and part of ECM related
diagnoses are continuously detected as NG for 5 trips, ECM warns the
driver that engine control system malfunctions and MIL circuit is open
by means of operating the fail-safe function.
The fail-safe function also operates when above diagnoses except MIL
circuit are detected and demands the driver to repair the malfunction. EC-973
DTC No. Detected items Engine operating condition in fail-safe mode
P0011
P0021 Intake valve timing control The signal is not energized to the intake valve timing control solenoid valve and the valve
control does not function.
P0101
P0102
P0103 Mass air flow sensor circuit Engine speed will not rise more than 2,400 rpm due to the fuel cut.
P0117
P0118 Engine coolant tempera-
ture sensor circuit Engine coolant temperature will be determined by ECM based on the following condition.
CONSULT displays the engine coolant temperature decided by ECM.
Condition Engine coolant temperature decided
(CONSULT display)
Just as ignition switch is turned ON
or START 40
°C (104 °F)
Approx 4 minutes or more after en-
gine starting 80
°C (176 °F)
Except as shown above 40 - 80
°C (104 - 176 °F)
(Depends on the time)
When the fail-safe system for engine coolant temperature sensor is activated, the cooling
fan operates while engine is running.
P0122
P0123
P0222
P0223
P2135 Throttle position sensor The ECM controls the electric throttle control actuator in regulating the throttle opening in
order for the idle position to be within +10 degrees.
The ECM regulates the opening speed of the throttle valve to be slower than the normal
condition.
Therefore, the acceleration will be poor.
P0196
P0197
P0198 Engine oil temperature
sensor Intake valve timing control does not function.
P0500 Vehicle speed sensor The cooling fan operates (Highest) while engine is running.
P0524 Engine oil pressure • ECM illuminates oil pressure warning lamp on the combination meter.
• Engine speed will not rise more than 4,000 rpm due to the fuel cut.
• Fail-safe is canceled when ignition switch OFF → ON.
P0605 ECM (When ECM calculation function is malfunctioning:) ECM stops the electric throttle control actuator control, throttle valve is maintained at a
fixed opening (approx. 5 degrees) by the return spring.
ECM deactivates ASCD operation.
P0643 Sensor power supply ECM stops the electric throttle control actuator control, throttle valve is maintained at a fixed opening (approx. 5 degrees) by the return spring.
P1805 Brake switch ECM controls the electric throttle control actuator by regulating the throttle opening to a small range.
Therefore, acceleration will be poor.
Vehicle condition Driving condition
When engine is idling Normal
When accelerating Poor acceleration
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

ECM
EC-629
< ECU DIAGNOSIS INFORMATION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
DTC Inspection Priority ChartINFOID:0000000009462544
If some DTCs are displayed at the same time, perform inspections one by one based on the following priority
chart.
P2100
P2103 Throttle control motor relay ECM stops the electric throttle control actuator control, throttle valve is maintained at a
fixed opening (approx. 5 degrees) by the return spring.
P2101 Electric th rottle control
function ECM stops the electric throttle control actuator control, throttle valve is maintained at a
fixed opening (approx. 5 degrees) by the return spring.
P2118 Throttle control motor ECM stops the electric throttle control actuator control, throttle valve is maintained at a fixed opening (approx. 5 degrees) by the return spring.
P2119 Electric thro ttle control ac-
tuator (When electric throttle control actuator does not function properly due to the return spring
malfunction:)
ECM controls the electric throttle actuator by regulating the throttle opening around the
idle position. The engine speed will not rise more than 2,000 rpm.
(When throttle valve opening angle in fail-safe mode is not in specified range:)
ECM controls the electric throttle control actuator by regulating the throttle opening to 20
degrees or less.
(When ECM detects the throttle valve is stuck open:)
While the vehicle is being driven, it slows down gradually because of fuel cut. After the
vehicle stops, the engine stalls.
The engine can restart in the N or P position, and engine speed will not exceed 1,000 rpm
or more.
P2122
P2123
P2127
P2128
P2138 Accelerator pedal position
sensor The ECM controls the electric throttle control actuator in regulating the throttle opening in
order for the idle position to be within +10 degrees.
The ECM regulates the opening speed of the throttle valve to be slower than the normal
condition.
Therefore, the acceleration will be poor.
DTC No. Detected items Engine operating condition in fail-safe mode
Priority Detected items (DTC) Detected items (DTC)
1 U0101, U1001 CAN communication line P0101, P0102, P0103 Mass air flow sensor
P0111, P0112, P0113, P0127 Intake air temperature sensor
P0116, P0117, P0118, P0125 Engine coolant temperature sensor
P0122, P0123, P0222, P0223, P1225, P1226, P2135 Throttle position sensor
P0128 Thermostat function
P0181, P0182, P0183 Fuel tank temperature sensor
P0196, P0197, P0198 Engine oil temperature sensor
P0327, P0328, P0332, P0333 Knock sensor
P0335 Crankshaft position sensor (POS)
P0340, P0345 Camshaft position sensor (PHASE)
P0460, P0461, P0462, P0463 Fuel level sensor
P0500 Vehicle speed sensor
P0520 EOP sensor
P0605, P0607 ECM
P0643 Sensor power supply
P0850 Transmission range switch
P1550, P1551, P1552, P1553, P1554 Battery current sensor
P1556, P1557 Battery temperature sensor
P1610 - P1615 NATS
P2122, P2123, P2127, P2128, P2138 Accelerator pedal position sensor
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM