2014 MITSUBISHI OUTLANDER SPORT maintenance

Fuses
Maintenance 11-17
11
E01007701753
The fuse capacity and the names of electricalsystems protected by the fuses are indicatedon the inside of the fuse lid (LHD vehicles),the back side of the glove box (RHD vehi-
cles) and inside of the fuse block cover(inside of the engine compartment).
E01007900790
A- Main fuse blockB- Sub fuse blockFuse load capacity
NOTE
zSpare fuses are provided on the cover ofmain fuse block in the engine compartment.Always use a fuse of the same capacity forreplacement.
Passenger compartment fuse loca-tion table
Main fuse block
Sub fuse block(LHD)Sub fuse block(RHD)
No.
Symbol
Electrical sys-
tem
Capacity
1
Electric win-dow control
30 A
*
2
Rear window demister
30 A
*
3 Heater 30
A
4
Wi n dsc reen wipers
30 A
5
Door locks 20 A
6
Rear fog lamp 10 A
7
Accessory socket
15 A
8
Rear window
wiper
15 A
9
Sunroof 20 A
10 Ignition
switch 10
A
11 Option 10
A
12
Hazard warn-ing flasher
15 A
13
4-wheel drive
system
10 A
14
Stop lamps(Brake lamps)
15 A
15
Instruments 10 A
BK0203201EN.book 17 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Fuses11-18 Maintenance
11
*: Fusible linkzSome fuses may not be installed on yourvehicle, depending on the vehicle modelor specifications.
zThe table above shows the main equip-ment corresponding to each fuse.
E01008001867
16
SRS airbag 7.5 A
17
Radio 15 A
18
Control unit
relay
7.5 A
19
Interior lamps(Room lamps)
15 A
20
Reversing lamps
(Backup lamps)
7.5 A
21
Heated door
mirror
7.5 A
22
Outside rear-view mirrors
10 A
23
Cigarette lighter/Accessory socket
15 A
24
Charge 7.5 A
25
Power seat 30 A
*
26
Heated seat 30 A
No.
Symbol
Electrical sys-
tem
Capacity
Engine compartment fuse location table Behind of the fuse block coverMain fuse block
No.
Sym-bol
Electrical sys-
tem
Capacities
SBF1
Air condition-ing condenser fan motor
30 A
*
SBF2 — — —SBF3 — — —SBF4
Radiator fan
motor
40 A
*
SBF5
Anti-lock brak-ing system
40 A
*
SBF6 — — —SBF7
Anti-lock brak-ing system
30 A
*
BF1
Electric tailgate 30 A
BF2
Audio system
amp
30 A
BF3 IOD IOD 30 ABF4 — — —F1 — — —F2
Wiper deicer 15A
F3 — — —F4
Daytime run-ning lamps
10 A
F5
Front fog lamps 15 A
F6 — — —
BK0203201EN.book 18 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Fuses
Maintenance 11-19
11
*: Fusible linkzSome fuses may not be installed on yourvehicle, depending on the vehicle modelor specifications.zThe table above shows the main equip-ment corresponding to each fuse.
F7
Headlamp washer
20 A
F8
Security horn 20 A
F9
Horn 10 A
F10
ETV 15 A
F11 — — —F12
Engine 7.5 A
F13
ENG/POWER 20 A
F14
Fuel pump 15 A
F15
Ignition coil 10 A
F16 — — —F17
Headlamp high beam (left)
10 A
F18
Headlamp high beam (right)
10 A
F19
Head-lamp low beam (left)
Dis-charge
20 A
No.
Sym-bol
Electrical sys-
tem
Capacities
F20
Head-lamp low beam (right)
Dis-charge
20 A
F21
Head-lamp low beam (left)
Halo-gen
10 A
F22
Head-lamp low beam (right)
Halo-gen
10 A
F23 — — —#1 — Spare fuse 10 A#2 — Spare fuse 15 A#3 — Spare fuse 20 ANo.
Sym-bol
Electrical sys-
tem
Capacities
No.
Sym-bol
Electrical sys-
tem
Capacities
SBF1
Electrical Park-
ing Lock
30 A
*
SBF2
Va c u u m p u m p (Regenerative
brake)
30 A
*
F1
Water pump (Electric motor)
20 A
Sub fuse block
BK0203201EN.book 19 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Fuses11-20 Maintenance
11
*: Fusible linkzSome fuses may not be installed on yourvehicle, depending on the vehicle modelor specifications.zThe table above shows the main equip-ment corresponding to each fuse.
The fuse block does not contain spare 7.5 Aor 30 A fuses. If one of these fuses burns out,substitute with the following fuse.7.5 A: 10 A spare fuse30 A: 30 A audio system amp fuseWhen using a substitute fuse, replace with afuse of the correct capacity as soon as possi-ble.
E01008101389E01007801884
1. Before replacing a fuse, always turn offthe electrical circuit concerned and put theoperation mode of the power switch inOFF.
2. Remove the fuse puller (A) from theinside of the main fuse block cover in theengine compartment.3. Referring to the fuse load capacity table,check the fuse pertaining to the problem.
F2 — — —F3 — — —F4
Fuel tank filler
door
7.5 A
F5
Solenoid valve (Air condition-
ing)
7.5 A
F6
Wa t e r p u m p (Air condition-
ing)
7.5 A
F7
Electric motor unit control
10 A
F8 — — —F9
Drive battery fun motor
15 A
F10
Ignition control 15 A
F11
Ignition control 7.5 A
No.
Sym-bol
Electrical sys-
tem
Capacities
Identification of fuse Capacity
Colour
7.5 A
Brown
10 A
Red
15 A
Blue
20 A
Ye l l o w
30 A
Green (fuse type) /Pink (fusible
link type)
40 A Green (fusible link type)
Fuse replacement
B- Fuse is OKC- Blown fuse
BK0203201EN.book 20 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Replacement of lamp bulbs
Maintenance 11-21
11
4. Insert a new fuse of the same capacity byusing the fuse puller into the same placein the fuse block.
E01003101805
Before replacing a bulb, ensure the lamp isoff. Do not touch the glass part of the newbulb with your bare fingers; the skin oil lefton the glass will evaporate when the bulb getshot and the vapour will condense on thereflector and dim the surface.
NOTE
zIf any system does not function but the fusecorresponding to that system is normal, theremay be a fault in the system elsewhere. Werecommend you to have your vehiclechecked.CAUTIONzIf the newly inserted fuse blows again after ashort time, we recommend you to have theelectrical system checked to find the causeand rectify it.zNever use a fuse with a larger capacity thanspecified or a substitute (such as a cable orfoil). Doing so could cause the circuit wiresto overheat and create a fire.
Replacement of lamp bulbs
CAUTIONzBulbs are extremely hot immediately afterbeing turned off.When replacing a bulb, wait for it to coolsufficiently before
touching it. You could
otherwise be burnt.zHandle halogen lamp bulb with care. The gasinside a halogen lamp
bulb is highly pressur-
ized, so dropping, knocking, or scratching ahalogen lamp bulb can cause it to shatter.zNever hold the haloge
n lamp bulb with a
bare hand, dirty glove, etc.The oil from your hand could cause the bulbto break the next tim
e the headlamps are
operated.If the glass surface is dirty, it must becleaned with alcohol, paint thinner, etc., andrefit it after drying thoroughly.
NOTE
zIf you are unsure of how to carry out thework as required, we
recommend you to con-
sult a specialist.zBe careful not to scratch the vehicle bodywhen removing a lamp or lens.zWhen it rains, or when the vehicle has beenwashed, the inside of the lens sometimesbecomes foggy. This is the same phenome-non as when window glass mists up on ahumid day, and does not
indicate a functional
problem.When the lamp is switched on, the heat willremove the fog. However, if water gathersinside the lamp, we
recommend you to have
the lamp checked.
BK0203201EN.book 21 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Replacement of lamp bulbs11-22 Maintenance
11
E01003200333
When replacing a bulb, use a new bulb withthe same wattage and colour.
E01003304042
Codes in parentheses indicate bulb types.
Codes in parentheses indicate bulb types.
Bulb location and capacity Outside Ty p e A : E x c e p t f o r h i g h i n t e n s i t y d i s -
charge headlamp type
FrontTy p e ATy p e B
Ty p e B : H i g h i n t e n s i t y d i s c h a r g e h e a d -
lamp type
1- Front turn-signal lamps: 21 W (PY21W)2- Headlamps, high beam: 60 W (HB3)3- Headlamps, low beam
Halogen: 55 W (H7)High intensity discharge: 35 W
4- Position lamps: 5 W (W5W)5- Front fog lamps: 55 W (H11)6- Side turn-signal lamps
WA R N I N GzAlways consult a specialist when repairingor replacing the bulbs
of high intensity
discharge headlamps.This is because the power circuit, bulbsand electrodes generate a high voltagethat could cause an electric shock.
1- High mounted stop lamp2- Reversing lamps: 21 W (W21W)3- Licence plate lamps: 5 W (W5W)4- Rear turn-signal lamps: 21 W (PY21W)5- Stop and tail lamps
NOTE
zThe following lamps are not possible torepair or replace only the bulb.If you need to repair or replace these lampbulbs, contact a MITSUBISHI MOTORSAuthorised Service Point.•Side turn- signal lamps•High mounted stop lamp•Stop and tail lampsRear
BK0203201EN.book 22 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Replacement of lamp bulbs
Maintenance 11-23
11
E01003401912
E01009301421
1. When replacing the bulb on the left sideof the vehicle, remove the bolt (A) hold-ing down the relay box and move therelay box.
2. Turn the cap (B) anticlockwise to removeit.3. Turn the socket (C) anticlockwise toremove it, and then pull the bulb out ofthe socket.4. To install the bulb, perform the removalsteps in reverse.
Inside 1- Luggage room lamp: 8 W2- Room lamp (rear): 8 W3- Map & room lamps (front): 8 W4- Downlight5- Vanity mirror lamps: 2 W6- Glove box lamp: 1.4 W
NOTE
zAn LED, not a bulb, is used in the downlight.Contact a MITSUBISHI MOTORS Author-ised Service Point when there is a need forrepair or replacement.
Headlamps (low beam, halogen bulb) *:Front of the vehicle
*:Front of the vehicle
BK0203201EN.book 23 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Replacement of lamp bulbs11-24 Maintenance
11
E01009401246
1. When replacing the bulb on the right sideof the vehicle, remove the clip (A) hold-ing down the washer tank and move thewasher tank.
2. Turn the cap (B) anticlockwise to removeit.3. Turn the bulb (C) anticlockwise to removeit, and then while holding down the tab(D), pull out the connector (E).4. To install the bulb, perform the removalsteps in reverse.
E01003702231
When replacing the bulb on the left side ofthe vehicle, move the relay box.(Refer to “Headlamps (low beam, halogenbulb): Step 1” on page 11-23)1. Turn the cap (A) anticlockwise to removeit.
Headlamps (high beam) *:Front of the vehicle
*:Front of the vehicle
Position lamps Except for vehicles equipped with high intensity discharge head-lamps *:Front of the vehicle
BK0203201EN.book 24 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分