The blue
0011indicator lamp in the
instrument cluster lights up when the high-
beam headlamps are switched on.
X To switch off the high-beam
headlamps: move the combination switch
back to its normal position.
The blue 0011indicator lamp in the
instrument cluster goes out.
i Vehicles with Adaptive Highbeam Assist:
when Adaptive Highbeam Assist is active,
it controls activation of the high-beam
headlamps (Y page 108).
High-beam flasher X
To switch on: turn the SmartKey in the
ignition lock to position 1or 2or start the
engine.
X Pull the combination switch in the direction
of arrow 0023. Hazard warning lamps
The hazard warning lamps automatically
switch on if:
R
an air bag is deployed
R the vehicle decelerates rapidly from a
speed of more than 45mph (70k m/h) and
comes to astandstill
X To switch on the hazard warning lamps:
press button 001A.
All turn signals flash. If you now switch on
at urn signa lusing the combination switch, only the turn signa
llam pont he
corresponding sid eofthe vehicle will flash.
X To switch off the hazard warning
lamps: press button 001A.
The hazard warning lamps switch off
automatically if the vehicle reaches aspeed
of over 6mph (10km/h) again after afull
brake application.
i The hazard warning lamps still operate if
the ignition is switched off. Cornerin
glight function The cornering light function improves the
illumination of the road over
awidea nglein
the direction you are turning, enabling better
visibility in tight bends ,for example. The
cornering light function can only be activated
whe nthe low-beam headlamps are switched
on.
Active:
R if you are driving at speeds below 25 mph
(40 km/h )and switch on the turn signal or
turn the steering wheel.
R if you are driving at speeds between
25 mph (40k m/h )and 45 mph (70k m/h)
and turn the steering wheel.
Not active: if you are driving at speeds above
25 mph (40 km/h) or switch off the turn
signa lorturn the steering wheel to the
straight-ahead position.
The cornering lamp may remain lit for ashort
time, but is automatically switched off after
no more than three minutes. Exterior lighting
107Lights and windshield wipers Z
Only operate the equipment when the traffic
situation permits. If you are not sure that this
is possible,p ark the vehicle paying attention
to traffic conditions and operate the
equipment when the vehicle is stationary.
When telephoning, you must observe the
legal requirements for the country in which
you are currently driving.
X Switch on your mobile phone and audio
system or COMAND, see the separate
operating instructions.
X Establish aBluetooth ®
connection to the
audios ystem or COMAND; see the
separate operating instructions.
X Press the 000Aor0004 button on the
steering wheel to select the Tel menu.
You will see one of the following display
messages in the multifunction display:
R Phone READY or the name of the network
provider: the mobile phone has found a
network and is ready to receive.
R Telephone No Service :t
here is no
network available or the mobile phone is
searching for anetwork.
Accepting acall Example: incoming call (color multifunction
display)
X Press the 0006button on the steering
wheel to accep tanincoming call.
If someone calls yo uwheny ou areint he
Tel menu
,adisplay message appear sinthe
multifunctio ndisplay.
If you are not in the Tel menu, you can still
accept acall. Rejecting or ending
acall X
Press the 0008button on the steering
wheel.
If you are not in the Tel menu, you can still
reject or end acall.
Dialin gane ntry from the phone book X
Press the 000Aor0004 button on the
steering wheel to select the Tel menu.
X Press the 0006,0005or000C button to
switch to the phone book.
X Press the 0006or0005 button to select the
desired name.
To start scrolling rapidly, pres sand hol dthe
0006 or0005 button for longe rthan one
second.
Rapid scrolling stops whe nyou release the
button or reach the end of the list.
X If only one telephone number is stored
for aname: press the 0006or000C button
to start dialing.
or
X If thereism ore thanone number for a
particular name: press the0006or000C
button to display the numbers.
X Press the 0006or0005 button to select the
number you want to dial.
X Press the 0006or000C button to start
dialing.
or
X If you do not want to makeac all:press
the 0008 or0002 button.
Redialing The on-board computer saves the last names
or numbers dialed in the redial memory.
X
Press the 000Aor0004 button on the
steerin gwheel to select the Tel menu.
X Press the 0006button to switch to the
redial memory.
X Press the 0006or0005 button to select the
desired name or number. 198
Menus and submenusOn-board computer and displays
