2014 Lexus IS250 Navigation Manual

57
2. NETWORK SETTINGS
IS300h/250_Navi_EE
BASIC FUNCTION
2
1Display the “Bluetooth*” screen.
(→P.56)
2Select “Bluetooth* setup”.
3Select the desired item to be set.
■DISPLAYING THE “Bluetooth* set-
up” SCREEN IN A DIFFERENT WAY
1Display the telephone top screen.
(→P.329)
2Select “Connect telephone”.
*: Bluetooth is a registered trademark of
Bluetooth SIG, Inc.
“Bluetooth* setup” SCREEN
FunctionPage
Registering a Bluetooth® device58
Deleting a Bluetooth® device59
Connecting a Bluetooth® device60
Editing the Bluetooth® device in-
formation62
IS_Navi_EE_53C71E.book 57 ページ ２０１４年５月２９日　木曜日　午前１１時２２分

58
2. NETWORK SETTINGS
IS300h/250_Navi_EE
1Select “A d d ”.
XWhen another Bluetooth
® device is con-
nected
zTo disconnect the Bluetooth® device,
select “Yes”.
XWhen 5 Bluetooth® devices have al-
ready been registered
zA registered device needs to be replaced.
Select “Yes”, and select the device to be
replaced.
2When this screen is displayed, search
for the device name displayed on this
screen on the screen of your
Bluetooth
® device.
zFor details about operating the Bluetooth®
device, see the manual that comes with it.
zTo cancel the registration, select “Cancel”.
3Register the Bluetooth® device using
your Bluetooth
® device.
zA PIN code is not required for SSP (Secure
Simple Pairing) compatible Bluetooth®
devices. Depending on the type of
Bluetooth® device being connected, a
message confirming registration may be
displayed on the Bluetooth
® device’s
screen. Respond and operate the
Bluetooth
® device according to the confir-
mation message.
REGISTERING A Bluetooth®
DEVICE
Up to 5 Bluetooth
® devices can be reg-
istered.
Bluetooth
® compatible telephones
(HFP) and audio players (AVP) can be
registered simultaneously.
This operation cannot be performed
while driving.
IS_Navi_EE_53C71E.book 58 ページ ２０１４年５月２９日　木曜日　午前１１時２２分

59
2. NETWORK SETTINGS
IS300h/250_Navi_EE
BASIC FUNCTION
2
4Check that the following screen is dis-
played when registration is complete.
zThe system waits for connection requests
coming from the registered device.
zAt this stage, the Bluetooth
® functions are
not yet available.
5Select “OK” when the connection sta-
tus changes from “Connecting...” to
“Connected”.
zIf an error message is displayed, follow the
guidance on the screen to try again.
1Select “Remove”.
2Select the desired device.
3Select “Yes” when the confirmation
screen appears.
4Check that a confirmation screen is dis-
played when the operation is complete.
DELETING A Bluetooth®
DEVICE
INFORMATION
●
When deleting a Bluetooth® phone, the
contact data will be deleted at the same
time.
IS_Navi_EE_53C71E.book 59 ページ ２０１４年５月２９日　木曜日　午前１１時２２分

60
2. NETWORK SETTINGS
IS300h/250_Navi_EE
1Select the device to be connected.
zSupported profile icons will be displayed.
: Telephone
: Audio player
zSupported profile icons for currently con-
nected devices will illuminate.
zDimmed icons can be selected to connect
to the function directly.
2Select the desired connection.
XWhen another Bluetooth
® device is con-
nected
zTo disconnect the Bluetooth® device,
select “Yes”.
3Check that a confirmation screen is dis-
played when the connection is complete.
zIf an error message is displayed, follow the
guidance on the screen to try again.
CONNECTING A Bluetooth®
DEVICE
Up to 5 Bluetooth
® devices (Tele-
phones (HFP) and audio players (AVP))
can be registered.
If more than 1 Bluetooth
® device has
been registered, select which device to
connect to.
zIf the desired Bluetooth® device is not on
the list, select “Add” to register the
device. (→P. 5 8 )
INFORMATION
●
It may take time if the device connection
is carried out during Bluetooth® audio
playback.
●Depending on the type of Bluetooth®
device being connected, it may be neces-
sary to perform additional steps on the
device.
IS_Navi_EE_53C71E.book 60 ページ ２０１４年５月２９日　木曜日　午前１１時２２分

61
2. NETWORK SETTINGS
IS300h/250_Navi_EE
BASIC FUNCTION
2
■AUTO CONNECTION MODE
zWhen the engine switch is in
ACCESSORY or IGNITION ON
mode, the system searches for a nearby
registered device.
zThe system will connect with the registered
device that was last connected, if it is
nearby.
■CONNECTING MANUALLY
1Press the “MENU” button on the
Remote Touch and select “Setup”.
2Select “Bluetooth*”.
3Follow the steps in “CONNECTING A
Bluetooth
® DEVICE” from “STEP 1”.
(→P.60)
*: Bluetooth is a registered trademark of
Bluetooth SIG, Inc.
■RECONNECTING THE Bluetooth®
PHONE
zIf a Bluetooth® phone is disconnected on
purpose, such as turning it off, this does not
happen. Reconnect the Bluetooth
® phone
manually.
To turn auto connection mode on, set
“Bluetooth* power” to on. (→P.65)
Leave the Bluetooth
® device in a loca-
tion where the connection can be estab-
lished.
When the auto connection has failed or
“Bluetooth* power” is turned off, it is
necessary to connect Bluetooth
® man-
ually.
If a Bluetooth® phone is disconnected
due to poor reception from the
Bluetooth
® network when the engine
switch is in ACCESSORY or
IGNITION ON mode, the sys-
tem automatically reconnects the
Bluetooth
® phone.
IS_Navi_EE_53C71E.book 61 ページ ２０１４年５月２９日　木曜日　午前１１時２２分

62
2. NETWORK SETTINGS
IS300h/250_Navi_EE
1Select the desired device to be edited.
2Select “Device info”.
3Confirm and change the Bluetooth®
device information.
EDITING THE Bluetooth®
DEVICE INFORMATION
The Bluetooth
® device’s information
can be displayed on the screen. The dis-
played information can be edited.
No.Information
The name of the Bluetooth® device.
Can be changed to a desired name.
(→P.63)
Device address is unique to the de-
vice and cannot be changed.
The telephone number of the
Bluetooth® phone.
Compatibility profile of the
Bluetooth® device.
Select to set the Bluetooth® audio
player connection method. (→P.63)
Select to reset all setup items.
IS_Navi_EE_53C71E.book 62 ページ ２０１４年５月２９日　木曜日　午前１１時２２分

63
2. NETWORK SETTINGS
IS300h/250_Navi_EE
BASIC FUNCTION
2
■CHANGING A DEVICE NAME
1Select “Device name”.
2Enter the name and select “OK”.
■SETTING AUDIO PLAYER CON-
NECTION METHOD
1Select “Connect audio player from”.
2Select the desired connection method.
“Vehicle”: Select to connect the audio sys-
tem to the audio player.
“Device”: Select to connect the audio play-
er to the audio system.
zDepending on the audio player, the “Vehi-
cle” or “Device” connection method may
be best. As such, refer to the manual that
comes with the audio player.
zTo reset the connection method, select
“Defaults”.
INFORMATION
●
If 2 Bluetooth® devices have been regis-
tered with the same device name, the
devices can be distinguished referring to
the device’s address.
●Depending on the type of telephone,
some information may not be displayed.
INFORMATION
●
Even if the device name is changed, the
name registered in your Bluetooth®
device does not change.
IS_Navi_EE_53C71E.book 63 ページ ２０１４年５月２９日　木曜日　午前１１時２２分

64
2. NETWORK SETTINGS
IS300h/250_Navi_EE
1Display the “Bluetooth*” screen.
(→P.56)
2Select “Detailed Bluetooth* settings”.
3Select the desired item to be set.
*: Bluetooth is a registered trademark of
Bluetooth SIG, Inc.
“Detailed Bluetooth* settings”
SCREEN
The Bluetooth® settings can be con-
firmed and changed.
No.InformationPage
Select to set Bluetooth®
connection on/off. 65
Displays system name. Can
be changed to a desired
name.65
PIN code used when the
Bluetooth® device was reg-
istered. Can be changed to
a desired code.65
Device address is unique to
the device and cannot be
changed.
Select to set the telephone
connection status display
on/off.
Select to set the connection
status display of the audio
player on/off.
Compatibility profile of the
system. 
Select to reset all setup
items.
IS_Navi_EE_53C71E.book 64 ページ ２０１４年５月２９日　木曜日　午前１１時２２分