2014 AUDI Q5 warning light

16 Instruments and warning/indicator lights
If the Jj;] indicator light turns on, the system
has switched the ESC
off . In this case, you can
switch the ignition
off and then on to switch
the ESC on again. The indicator light turns
off
when the system is functioning fully.
If the
11 indicator light turns on, ESC was re­
str icted using the
I~ OFF I button ¢ page 197.
Stabilization control (ESC/ABS): Fault! See
owner's manual
I f the
Jj;] indicator light and the ABS ind icator
l ight ~ (USA models)
Iii] (Canada models)
turn on and the message appears, the ABS or
e lectronic differential lock is ma lfunctioning.
This a lso causes the ESC to malfunction . The
brakes st ill function with the ir normal power,
but ABS is not active.
Drive to your authorized Audi dea ler or quali ­
fied workshop immediately to have the mal­
function corrected.
A WARNING
-
If the ~ (USA models)/ . (Canada
models) brake system ind icator light turns
on together with the ABS and ESC ind ica­
tor lights, the ABS/ESC regulating function
may have fai led. Functions that stabilize
the vehicle a re no longer ava ilab le. This
could cause the vehicle to swerve and in­
crease the risk of sliding. Drive carefully to
the nearest a uthorized Audi dea ler or oth­
er qualified workshop and have the mat-
function corrected.
(D Tips
For additional information on ESC and
ABS, refer to¢
page 197.
it !f Safety systems
The fl (USA models) tE,I (Canada models) in­
dicator light monitors the safety systems (e.g.
a ir bags, pretensioners) and illuminates for a
few seconds each time you switch the ignition
on .
If the
fl (USA models) tE,I (Canada models)
indicator light does not go out, or if it illumi- nates while you are driving, or if it starts to
blink,
then there is a malfunction somewhere
in the system. If the light does not illuminate
when you switch the ign ition on, this also
means there is a malfunction.
A WARNING '"--
If you have a malfunction in the safety sys-
tems, contact your authorized Audi dealer
imme diately. Otherwise the safety sys­
tems may not work properly in an acc i­
dent.
ill Tire pressure monitoring system -
telltale indicator lamp
Applies to vehicles: wit h tire p ressu re mo nito rin g system
The warning/indicator light appears in the
event of a significant loss of tire pressure or if
there is a malfunction .
The ind icator light IE illuminates to check
the function when you switch on the ignition.
If the
IE symbol remains on or blinks after
you sw itch on the ign it ion, there is a loss of
t ir e pressure or a system malfunction. If there
is a system ma lfunction, see your authorized
Audi dealer as soon as possible.
Detailed informat io n on the tire p ressure
monitoring system can be found in
¢page 265.
¢¢Turn signals
The indicator light blinks when you use either
turn signal.
Whenever you use the left (I or the r ight II
turn sig nal, the indicator light blinks. When
you use the emergency flashers, both indica­
tor lights flash .
If one of the turn signa l light bulbs burn out,
the turn sig nal will blink twice as fast as nor­
mal.
This does not apply, however, in towing mode .
The indicator light does not flash if a turn sig­
nal is out on the tra ile r or the towing vehicle. .,.

Instrument s and warnin g/indic ator ligh ts 17
Additional information on the turn signa ls
~ page 52.
¢19 Trailer turn signal assembly
App lies to vehicles: with towing hitch
The indicator light also blinks if the turn sig ­
nal is operated when towing a trailer .
The indicator ligh t. blinks when the t urn
signal is used, if a trailer has bee n properly
connected to the vehicle .
If one of the turn s ignal bulbs on the tra ile r i s
bu rned out or defective, the indicato r light
will not b link when you use the turn signals.
(j) Tips
For veh icles with a factory installed towing
hitch o r a trailer h itch tha t was installed
la ter ac co rding to fac tory specifications,
the trailer t urn signa l assemb ly is actuat ­
ed .
,i Safety belts
This warning/indicator light reminds you to
put on your safety belt.
The . warning/ind icator lig ht ill uminates
when the igni tion is sw itched on to rem ind
the driver and (on USA models only) any front
passenger to put on the safety belt . Add ition­
a lly, an audible warning tone will a lso sound .
F or more Information
~ page 149, Safety
belt warning light .
a Malfunction Indicator Lamp (MIL)
The Malfunction Indicator Lamp (MIL) is part
of the On-Board Diagnostic (OBD II) system.
The symbol
¢"lift lights up when the ignit ion is
turned on and will turn off after the engine
has started and has sett led at a constant idle
speed. Th is ind icates that the MIL is working
p roperly .
The warning light illuminates when there is a
malfunct ion in the engine e lectronic system. Contact your a
uthorized Audi dea ler and have
the malfunction corrected .
An improperl y clo sed fu el filler cap may al so
cau se the MIL light t o illumin ate (onl y
vehicles with g asoline engi ne)
q page 226.
Fo r more information
q page 26.
[D High beam
The ii warn ing/indi cator lig ht ill uminates
when the high beams a re on or when you use
the headlight flasher. For more information
about using the high beams, see
¢ page 52.
CRUISE/" (') Cruise control
The MjlO~i4 (USA mode ls) Jill (Canada models)
warning/indicator light illuminates when the
cruise control is activated .
ABS/(@) Anti-lock brake system (ABS)
This warning/indicator light monitors the ABS
and the electronic differential lock (EDL).
The fJ] (USA models) ; ri] (Canada mode ls)
warning/indicator light will come on for a few
seconds when the ignition is switched on. The
light will go out after an automatic check se­
quence is completed.
There is a malfunct ion in the ABS when:
- The warning/indicator light does not illum i­
nate when you switch on the ignition.
- The warning/indicato r light does not go o ut
after a few seconds.
- The warning/indicato r light i lluminates
wh ile driving.
The brak e system will still re spond e ven
without the assistance of the ABS system.
See your autho rized Audi deale r as soon a s
possible to re store full br aking performance.
For more information regard ing the ABS
q page 197.
The ABS warning light and the b rake warn­
ing light come on togethe r. The ABS will not
wo rk and you will notice a change in b raking
response and performance . .,,.

18 Instruments and warning/indicator lights
Malfunction in the brake system
If the brake warning light c::> page 18 and
the ABS warn ing illuminate
together there
may be a ma lfunction in the ABS, and there
may also be a malfunction in the brake system
itself
c::> A .
In the event of a malfunction in the brake
system
the warning/indicator light 1111
(USA models);II (Canada models) in the in­
strument cluster flashes. By pressing the
! SET !
button, you can bring up a dr iver message
which explains the malfunction in more de­
tail. Please note
c::> page 29.
Malfunction in the electron ic differential
lock (EDL)
The EDL works together with the ABS. The
ABS warning light will come on if there is a
malfunction in the EDL system
c::> page 197.
See your authorized Aud i dealer as soon as
possib le.
.&_ WARNING
-
- If the~ (USA models) l[!J (Canada
mode ls) warning light does not go out,
or if it comes on while driving, the ABS
system is not working properly. The vehi­
cle can then be stopped only with the
standard brakes (without ABS). You will
not have the protection ABS provides.
Contact your authorized Aud i dealer as
soon as poss ible.
- If the
1111 (USA models)/. (Canada
mode ls) brake system indicator light
turns on together with the ABS and ESC
indicator lights, the ABS/ ESC regu lating
function may have failed. Functions that
stabilize the vehicle are no longer availa­
ble. This could cause the vehicle to
swerve and increase the risk of sliding.
Drive caref ully to the nearest authorized
Audi dealer or other qualified workshop
and have the malfunction corrected.
::\ii(®) Electromechanical parking brake
The warning/indicator light monitors the
electromechanical parking brake.
With the parking brake applied and the igni­
tion turned on, the. (USA models)/ . (Can­
ada models) warn ing/ indicator light illumi­
nates. After the ignition has been turned off,
the warn ing/ indicato r light continues to illu­
minate for about 30 seconds.
If the parking
brake is applied with the ignition turned off,
the warn ing/indicato r light illuminates for
about 30 seconds.
T he wa rning/i ndicator lig ht will go out when
the parking brake is released.
If the warning/indicator light flashes continu­
ously
after applying the pa rking brake, brak­
ing force is not sufficient to prevent the veh i­
cle from rolling unintentionally . Please note
the following:
- If the slope of the ground is too steep to
pa rk the vehicle, the additional drive mes­
sage appears Caution : Vehicle parked too
steep.
- In the event of a pa rking brake malfunction,
the yellow
IIJ symbo l appears in the instru­
ment cluster display and the driver message
Parking brake malfunction! is displayed.
Have the ma lfunction repa ired as soon as
possible by an authorized Audi dealer or any
other qualified workshop.
BRAKE/((D) Brake system
The warning/indicator light flashes if brake
fluid level is low, if there is an ABS system
malfunction or a parking brake malfunction.
The 1111 (USA models)/ . (Canada models)
li ght illuminates when the ignition is turned
on. It goes out after the engine has been
started . This indicates that the brake warning
l ight is functioning properly.
If the brake warning light does not light up
when the engine is cranking, there may be a
malfunction in the electrical system. In this
case, contact an authorized Audi dealer. ..,.

Instrument s and warnin g/indic ator ligh ts 19
If the brake system warning/indicator light
flashes, there is a brake system malfunction. By pressing the
ISETI b utton, you can br ing up
a driver message which exp la ins the malfunc­
tion in more detail¢ page
29.
If the ABS fails, the ABS warning/indicator
light
fJln (USA models) ,11J (Canada models)
flashes together w ith the brake system warn­
ing/indicator light¢,& .
(USA models): If the warning light
11111 and
the warning light
EIJ i llum inate together, im­
mediately contact your author iz ed Audi dealer
or qualified workshop to have all brake pads
inspected ¢ page
33 .
When the light comes on, an audib le warning
signa l is also given.
A WARNING
- If the 11111 (USA models)/ . (Canada
models) brake system indicator light
tu rns on together with the ABS and ESC
indicator lights, the ABS/ESC regu lating
function may have failed. F unctions that
stabilize the vehi cle are no longer availa­
ble. Th is could cause the vehicle to
swerve and increase the risk of sliding .
Drive carefully to the nearest a uthorized
Audi dealer or other qualif ied workshop
and have the malfunction corrected.
- If the brake warning/indicator light does
not go out after a few seconds and the
parking brake is released, or lights up
wh ile you are driving, the fluid level in
the brake fluid reservoir is too low . If you
believe that it is safe to do so, proceed
immediately at low speed to the nearest
au thori zed Audi dealer o r qualified re pair
f acili ty and have the brake system in­
spected.
- Always keep in m ind tha t after several
brake applicat ions, yo u will need greater
pressure on the brake peda l to sto p your
vehicle. Do not re ly on stra ined brakes to
respond w ith maxim um stopp ing power
in critical situations. You must allow for
increased braking distances. The extra distance used up by fading brakes could
lead to an accident.

20 Driver in formation d ispl ay
Driver information
display
Introduction
General notes
The driver information display inside the in­
strument cluster provides you , the driver ,
with much useful information.
Fig . 9 Instrument cl uster: ce nte r dis play
Information from the driver information sys­
tem is shown in the display in the center of
t he instrument cluster .
When you turn on the ignition and while you
are driving, some functions and vehicle com ­
ponents are scanned for their operating sta­
tus. Malfunctions or required service proce­
dures are signaled audibly and shown by red
and yellow lighted symbols and rem inders to
the dr iver in the display.
T he driver is also shown information about ra­
d io and CD operation and directions for the
navigation system*. You can find add itional
information on these subjects in the rad io or
MMI* manual.
The illustrations in the instrument panel dis ­
play differ in some of the vehicles .
The driver information system provides the
following functions :
Sound system disp lay
Q page 20
Outside air temperature Qpage 21
Digital speedometer Qpage 21
Open door- and luggage com-Qpage 21
partment warning
Service interval display
Q page22
Auto Check system <::>page27
Driver information Qpage27
Speed warning Qpage 93
Trip computer Qpage23
Tire pressure monitoring sys-Qpage265
tern*
Digita l clock with date display
Qpage 12
Odometer and trip odometer Qpage 13
Selector lever position Qpage 123
Cruise control c::>page95
Adaptive cruise control* c::> page 10 7
Energy flow display* <::> page 103
¢j) Tips
In the event of a malfunction either a red
or yellow icon appears in the display . Red
symbols indicate
Danger c::> page 28. Yel­
l ow symbo ls indicate a
Warning
c::> page 31.
Sound system display
Fig. 10 D isplay : sound system
(0
"' .... 9 a:
~
If priority 1 or pr iority 2 faults are not shown
by the Auto Check Control , the name of the ra­
dio sta tion you are tuned to or the frequency
and the reception range are shown in the up­
per area of the display.
When the CD is in use, the title of the track
being played is shown . T he CD changer dis­
plays the number of the current CD (CD
1 to
CD6) .

Outside temperature display
Fig. 11 D isplay : outside te mpe rature
At temperatures below 39 °F (+4 °C), a snow­
f lake symbol appears in front of the tempera­
ture display . It is intended to rem ind the driv ­
er to pay special attent ion to
ice on the roa d.
If the vehicle is stationary, or if you are driving
at a very low speed, the temperature shown in
the display might be slightly higher than the
actual outside temperature . Th is is caused by
the heat being radiated from the engine .
The unit of measurement for the temperature
can be set in either °For in °Con the MMI* or
on the radio control un it . The outside temper­
ature display automatical ly shows the unit of
measurement that has been set. For addition­
a l information, see the MMI* or the radio in ­
struction manua l.
A WARNING
- Never use the outside temperature d is ­
play to determine if a road surface is icy
or not. Keep in mind that road surfaces ,
especially bridges and overpasses, could be ice covered and slippery even at an
outside temperature above 39 °F (+4 °C).
- Always remember, eve n if the "snow­
flake" symbol ( ice warn ing) does not ap­
pear i n the display, black ice could be on
the road .
-Always reduce your speed and dr ive with
special care in cold weather conditions
when the chance of encounte ring icy
road surfaces increases .
Driver inform ation di spl ay 21
Digital speedometer
Fig. 12 D ispl ay : D ig it a l speedometer
Current speed appears in the disp lay. Speed is
shown in 1 mph increments (USA mode ls) or 1
km/h increments (Canada models) .
You can switch the disp lay from mi les to kilo ­
meters and vice versa via the radio or MMI* .
Open door or trunk lid warning
The pictogram alerts you when doors or the
trunk lid have been left open .
Fig. 1 3 Disp lay: Open doo r· and tr unk lid wa rnin g
T he Open Door/Trunk L id warn ing displays if
even one door, the hood or the t runk lid is
open . T his symbo l also shows which door or
lid has no t been closed
~ fig. 13 .
As soon as the doo r, the hood and the trunk
lid a re closed proper ly, the door and trunk lid
warning turns off and the selected d river in­
format ion sys tem func tion s are d isplayed
again .

26 Driver information d isplay
program. The fuel economy messages turn off
automatically after a certain per iod of t ime .
.,. To turn a fue l economy message off immedi­
ately after it appears, press the
!RESE T I but­
ton ¢
page 24, fig. 17 @, or
.,. Press the funct ion selection switch
¢ page 24 , fig. 17@.
(D Tips
-Once you have turned a fuel economy
message off, it will only appear again af­
ter you turn the ignition on again.
- The fuel economy messages are not dis­
played in every instance, but rather in in­
tervals over a period of time.
On-Board Diagnostic
system (OBD)
Malfunction Indicator Lamp (MIL)
T he Malfunction Indicator Lamp (MIL) ¢4 in
the instrument cluster¢
page 14, fig. 8 is
part o f the On-Board Diagnostic (OBD II) sys­
tem.
T he warning/indicator light illuminates when
the ignition is switched on and goes out after
the engine starts and the idle has stabilized .
T his indicates that the MIL is working proper ­
ly .
If the light does not go out after the engine
is started, or illuminates while you are driv­
ing, a malfunction may exist in the engine sys ­
tem. If the light illuminates, the catalytic con­
verter could be damaged.
Continue driving
with reduced power (avoid­
ing sustained high speeds and/or rapid accel­
erat ions) and have the condition corrected .
Contact your authorized Audi dealer.
If the light illuminates, the electronic speed limiter may also be malfunctioning. For more
information ¢
page 2 7, Electronic speed
limiter .
An improperly closed fuel filler cap may also
cause the MIL light to illuminate (only
vehicles with gasoline engine)
¢ page 226 .
On-Board Diagnostics
Fig. 21 Location of Data Li nk Conn ecto r (DLC)
On-Board D iagnostics monitors the compo­
nents of your emission control system . Each
monitored component in your engine system
has been ass igned a code . In case of a mal­
function, the component will be identified
and the fault stored as a code in the control
module memory.
The MIL light may also illuminate if there is a
leak in the on-board fuel vapor recovery sys­
tem .
If the light illuminates after a refueling,
stop the vehicle and make sure the fuel filler
cap is properly closed (only vehicles with gaso­
line engine) ¢
page 226.
In order to make an accurate diagnosis, the
stored data can only be displayed using spe­
cial diagnostic equipment (generic scan tool
for OBD).
In order to connect the special diagnostic
equipment, push the plug into the Data Link
Connector (DLC). The DLC is located to the
right of the hood release
¢fig. 21.
Your authorized Audi deale r or qualified work­
shop can interpret the code and perform the
necessary repair.
.&_ WARNING ~ -
Do not use the diagnostic connector for
personal use. Incorrect usage can cause
malfunctions, which can increase the risk
of a collision!

Ignition lock malfunction
¢ page 31
Hybrid drive*
¢page 99, ¢page 105
0 Alternator malfunction
If the . symbol in the instrument panel d is­
play flashes, then there is a malfunction in the
alternator or the vehicle electronics. A warn­
i ng to the driver w ill appear, too . The driver
warn ing goes out after about 5 seconds, but it
can be brought up at any time by pressing the
ISE TI button again .
Usually, you can still d rive to the next dealer­
ship . Turn off all but the most necessary elec­
tr ica l consumers, since these d ra in the ve hi­
cle's battery.
@ Note
If the . warning symbo l (coolant system
malfunct io n) also lights up on the inst ru­
men t pa nel d uring the t rip
¢page 30,
t hen you have to stop immediately and
turn off the eng ine. The coolant pump is
not working anymore -danger of damage
to the eng ine!
BRAKE/C CD) Brake system malfunction
A malfunction in the brake system must be
repaired as soon as possible.
If the warning /indi cator light 11111 (USA
models)/ . (Canada mode ls) in the instru ­
ment cluster flashes, there is a brake system
malfunct ion. A dr iver message appears as
well to explain the malfunction in more de­
tail. The driver warning goes out after about 5
seconds, but it can be brought up at any time by pressing the
I SET I button aga in.
Stop veh icle and check brake fluid level
... Stop the vehicle.
... Check the brake fluid level¢
page 241.
.,. Seek profess iona l assistance if necessary.
Dri ver information di spla y 29
Warning! Fault in brake system. Contact
workshop
... Drive carefully to the nearest authorized
Aud i dea ler or other qua lified workshop and
have the malfunction corrected ¢
&-
Parking b rake system fault! See owner' s
manual
i,-If this symbo l appears when the vehicle is
stat io nary or after the ignition is tu rned on,
check to see if the park ing brake can be re­
leased . Drive to an author ized Audi dealer or
other qualified workshop as soon as possi­
b le and have the malfunction cor rected. If
t he par kin g b rake cannot be opened, t hen
t ake it to an expe rt at an au tho riz ed Audi
dea le r.
... If the symbo l appears while you are d riving,
it is possible that the traction contro l or t he
emergency brake has mal functioned .
It is
possible t hat the parking brake cannot be
app lied. It is also possible that the parking
brake cannot be re leased after it has been
app lied. D rive to an autho rized Aud i deale r
or ot her qualified wo rkshop to have the mal­
fun ction co rrected.
If th e ABS system malfunctions , the ABS
warning/ind icator light illum inates together
wi th t he b rake sys tem ma lfunction wa rning/
i ndica tor ligh t¢ .&. -
_& WARNING ,...___
-Always observe the warn ings in
¢page 231, before openi ng the hood
an d checking the brake f luid .
- Driving with low brake f lui d is a safety
hazard. Stop the car and get professiona l
assistance.
- If the
11111 (USA models) . (Cana da
mo dels) brake system ind icator light
turns on together with the ABS and ESC indicator lights, the ABS/ESC regulat ing
function may have failed. Functions that stabilize the vehicle a re no longer avai la­
ble. This could ca use the vehicle to
swerve a nd increase the r is k of slid ing .
Dr ive ca re fully to the nea rest au thori zed