Page 49 of 286

-Never drive when the power top is not
locked correctly. The wind from driving
could cause the power top to open. This
can result in injuries and damage to the
vehicle .
(D Tips
Have a second person assist when closing
the power top. Positioning the power top
is easier when there is a second person to
help .
Step 1: Unlocking the power top
compartment cover
The release lever for the power top compart
ment is located under the trim in the luggage
compartment.
Fig. 39 Luggage compartmen t: re lease leve r
Fig. 40 Luggage compartmen t: side trim
.,. Open the luggage compartment lid. The
emergency release can be used if the lug
gage compartment lid will not open
<=:> page 38.
"" Reach your finger into the gap behind the
trim near the center of the vehicle .
"" Pull the release lever down to release the
power top compartment cover
c:> fig. 39.
Power top 47
.,. Open the left side trim and press the yellow
lever in the d irection of the arrow
c:> fig. 40.
.. Remove the emergency key from the com
partment on the left side @.
.,. Open the right side trim and press the yel
low lever in the direction of the arrow .
Step 2: Lifting the power top
compartment cover out
Fig. 41 Lug ga ge compart men t lid co m plete ly ope n
Fig. 42 Storage bay cover partiall y open
.,. Press the luggage compartment lid in the
direc tion of the arrow
c:> fig . 41 .
.,. Raise the power top compartment cover out
of the power top tray and hold it in place
c:> fig. 42 c:> ,&. .
Have a second person assist when raising the
power top compartment cover . That person
should stand on the opposite side of the vehi
cle and perform the same steps .
.&_ WARNING
When raising the power top compartment
cover, avoid contact with the supports or
other moving parts. Otherwise you could
pinch your hands.
Page 50 of 286

48 Power top
Step 3: Lifting the power top storage
bay cover out
Fig. 4 3 Luggage compartment lid closed
Fig. 44 Power top sto rage bay cover completely open
... Close the luggage compartment lid .
11--Open the power top storage bay cover com
pletely
c::> fig. 44 .
..&, WARNING
When ra is ing the power top storage bay
cover, avoid con tact w ith the s upports o r
other moving parts . Othe rwise you cou ld
pinch your hands.
Step 4: Closing the power top
F ig . 4 5 Removi ng the cover
Fig. 46 Emergency key for ope ning the latches
11--Remove the cap on the trim .
11--Insert the emergency key in the open ing
(hex socket) .
11--Turn the release key counterclockwise until
it stops to open the latch .
... Remove the emergency key.
Step S: Closing the power top
The power top must be positioned by hand.
Fig . 47 Power top partially open
Fig. 4 8 Winds hie ld: Power top
11--Raise the power top out of the tray c::> .&. in
Step 2: Lifting the power top compartment cover out on page 47 .
11--Pull the power top out completely .
., Press the power top onto the windshield
frame
c::> fig . 48 .
Page 51 of 286

.. Press the switch ~ ¢ page 44, fig. 32 to
close the convertible top. If this does not
work, proceed w ith
¢ page 49, Step 6: Re
tracting the power top comportment cover.
Have a second person assist when posit ioning
the power top . That person should stand on
the opposite side of the vehicle and perform
the same steps.
A WARNING
- When positioning the power top, avoid
contact with the supports or o ther mov
ing parts. Otherwise you could pinch
yo ur hands .
- When pressing the power top down onto
the windsh ie ld frame, make su re that
you do not pinch yourse lf or anyone else .
Step 6: Retract ing the power top
compartment cover
The power top comportment cover must be
retracted by hand.
F ig . 49 Power top raised
-
.. Raise the rear of the power top and hold it in
place
i::> fig. 49 © i::> A in Step 2: Lifting the
power top compor tment cover out on
page 47 .
.,. Slide the power top compartment forward
u nti l it reaches the end position @. Release
the power top.
A WARNING
Do not pinch yo urself o r othe rs when clos
ing the power top compartment.
Power top 49
Step 7 : Locking the power top
The locking system for the power top latches
ore located on the inside of the power top .
Fig . SO In side of the powe r top : hex key fo r eme rgency
oper atio n
.. Insert the emergency key in the open ing and
turn it clockwise unt il it stops to lock the
power top .
.,. Remove the emergency key .
.. Cover the opening w ith the cap.
(D Tips
Make sure the locking mechanisms are
l ocked secure ly.
Step 8 : Loosen ing the headliner
F ig. 51 Power top: area around the rig ht s ide o f th e
rear window
F ig. 52 Area a ro un d t he r igh t sid e of th e rear w indow :
,._ 0 ,._ ~
>< co a,
headliner part ia lly loose ned •
Page 52 of 286
50 Power top
Perform the following steps in the rear win
dow area of the power top on each side .
.,. Pull the loops (marked in yellow) w ith the
eme rgency key to loosen the headliner .
.,. Pull at the yellow marking again to loosen
the headliner around the rear window (ap
proximate ly 30 cm).
Step 9: Securing the latch
Fi g. 53 Rear of the power top: Securing the latc h
The latches must be secured on the left and
right sides of the vehicle .
.,. Pull the power top headliner to the side in
the area around the rea r headrests to sec ure
the latches~
fig. 53 ~.&. in Step 2: Li~ing
the power top compartment cover out on
page 47 .
.,. Then remove the emergency key and insert
the short end into the power top support at
the yellow marking .
.,. Press the emergency key in the direction of
the arrow @ unt il the latch is secure .
A WARNING
Do not pinch yourself or others when clos
ing the power top compar tment.
Page 53 of 286

Clear vision Lights
Switching the lights on and off
F ig . 54 Instrument pane l: headlight control switch
Light switch ·'t/,·
Turn the switch c> fig . 54 to the correspond ing
position . When the lights are switched on, the
:oo: symbol turns on.
0 • The lights are off or the dayt ime running
lights are on:
- USA mod els : The daytime running lights are
activated when the light sw itch
c> fig . 54 is
in the
O position or the AUTO position (only
in daylight conditions) . The daytime running
lights function can be turned on and off in
the radio or MMI* menu
E xterior li ghtin g
¢page 52, c> &_ .
-Ca nada mod els: The daytime runn ing lights
are activated when the light sw itch
¢ fig . 54
is i n the O position, :oo : position or the AUTO
posit ion (on ly in daylight cond itions). The
daytime running lights function cannot be
turned off¢&. .
AUTO* -Automatic headlights switch on and
off depending on b rightness, for example in
tw ilight, during rain or in tunnels¢,& .
:oo: -Side marker lights
~D -Low beam headlights
Fog light s/rear fog ligh t(s)*
Press the appropriate button c> fig. 54:
1D -Fog lights
0$ -Rear fog light(s)
Clear vi sion 51
adaptive light*
When switched on, adaptive ligh t adap ts to
curves in the road depend ing on the vehicle
speed and the steering ang le. This provides
better lighting through the curve. The system
operates at speeds between approximately 6 mph (10 km/h) and 68 mph (110 km/h).
Sta tic corner ing light * (vehicles with adaptive
light) -the cornering light switches on at
speeds up to approximately 25 mph (40 km/ h) when a certain steering wheel angle is
reached or when a turn signal is activated. The
area to the s ide of the vehicle is illuminated
better whe n turn ing .
The adaptive light and the cornering light only
function when the switch is in the AUTO posi
tion (automatic headlights*) .
A WARNING
-Daytime running lights and automatic
headlights* are only intended to ass ist
the driver . T hey do no t re lieve the driver
of his responsibility to chec k the head
lights and to t urn them on manua lly ac
cording to the current light and visibility
conditions. For examp le, fog cannot be
detected by the light sensors*. So a lways
switch on the headlights
~D under these
weather conditions and when driving in
the dark .
- Cras hes can happen when you cannot see
the road ahead and when you cannot be
seen by other motorists. Always turn on
the head lights so that you can see ahead
and so that others can see your car from
the back.
- Please obey all laws when using the
lig hting sys tems described here.
(D Note
The rear fog lights* should on ly be turned
on in accordance with t raff ic regulation, as
the lights are bright for following traffic. ..,.
Page 54 of 286

52 Clear vis ion
@ Tips
- The light sensor* for headlight control is
located in the rear view m irror mount.
You should therefore not apply any st ick
ers to the windsh ield in this area in order
to prevent malfunctions or failures.
- Some exterior lighting functions can be
adjusted
¢page 52.
- When you remove your key from the igni
tion while the vehicle's lights are turned
on, a buzzer sounds as long as the driv
er's door is open .
- In cool or damp weather, the ins ide of
the headlights, turn signals and tail lights can fog over due to the tempera
ture difference between the inside and
outside. They will clea r shor tly after
switching them on. This does not affect
the service life of the lighting.
- In the even t of a light sensor malfunc
tion, the driver is no tified in the instru
ment cluster disp lay¢
page 22.
Turn signals and high beam lever
The lever operates the turn signals, the high
beams and the headlight flasher .
Fig. 55 Tu rn s ig na l and hig h beam lever
Turn sign als ¢i ¢
The turn signals activate when you move the
l ever into a turn s ignal pos ition when the ign i
tion is switched on.
(D -right turn signal
@-left tur n signa l
The turn s ignal blinks three times if you just
tap the lever .
High be ams and headlight flasher [D
Move the lever to the correspon ding posit io n:
@ -high beams on
@ -high beams off or headlight flasher
The indicator light
ii in the instrument cl us
te r turns on .
Notes on thes e features
-The turn signals on ly wor k w ith the ignition
t ur ned on. The indicator ligh ts
Ct or a in
the instrument cluster also blink.
- After you have turned a co rner, the turn s ig
na l switches off au toma tically .
- The
high beam works on ly w hen the head
lights a re on. The ind icator ligh t
II in the
instrument cluster illuminates when the
high beams are on .
- The
headlight flasher works o nly as long as
you ho ld the lever -even if there a re no
lights switched on . The indicator light
II in
the instrument cluster illuminates when you
use the headlight flasher.
A WARNING
--
Do not use the h igh beam or headlight
flasher if you know that these could blind
oncom ing traffic.
Adjusting exterior lighting
The functions ore selected in the radio or
MMI" .
.,. Select: !CARI function button> Exte rior
light ing .
Or
.,. Select: !CARI function button > Car systems *
control button > Vehicle s etting s> Exterior
lighting .
Coming home (light when leav ing car }*,
Leav ing home (light when unlocking car )*
The coming home function illuminates the
area around the vehicle when the ignition is
switched off and th e dr ive r's door is open ed.
Depend ing on veh icle equ ipment, the function
can be switched on and off or the length of
time the lig hts remain on* can be ad justed . ..,.
Page 55 of 286

The leavin g home function i lluminates the
area around the vehicle when unlock ing it.
T his function can be switched on and off.
The
c o ming h om e and lea ving home func
tions on ly operate when it is dark and the
light switch is in the AUTO posit ion
¢ page 51 , fig. 54 .
Auto headlight s*
When the light switch is in the A UTO
¢ page 51 position, the switch-on po int of the
lights can be changed in the automatic driving
light function.
Daytime running lights
USA m odel s:
You can switch the dayt ime run
ni ng lights
on and o ff .
Canada mod els:
The function cannot be
turned off .
It is activated a utomat ica lly each
time the ignition is switched on.
Travel mode*
T he headlight beam is asymmetrical. This pro
v ides stronger illum ination on the s ide of the
road on wh ich you are driving .
If you are driv
i ng in a country that d rives on the opposite
side of the road from your own country, th is
will cause glare for on coming drivers. To pre
vent glare:
- Trave l mode must be selected in vehicles
with Xenon headlights*.
- In veh icles with halogen headlights, ce rtain
areas of the head light lenses must be cov
ered with wate rproof adhesive covers that
prevent light from passing thro ugh. For
more informat ion, please see your author
i z ed Audi dea ler or author ized repa ir faci lity .
(D Tips
When trave l mode is activated, a display in
the driver information system indicates
this each time you switch the ignit io n on.
Clear vi sion 5 3
Emergency flashers
Fig. 56 Center co n sole : em erge ncy flasher sw itc h
The emergency flashers makes other moto
rists aware that you or your vehicle are in an
emergency situation .
.. Press the switch
Gil ¢ fig. 56 to turn the
emergency flashers on or off .
When the emergency f las hers are on, all four
turn s ignals b link at the same time. The turn
s ignal indicator lights .
1B in the instru
ment cluster, as well as the light in the emer
gency flasher switch ~ blink likewise.
You can indicate a lane change or a tu rn w hen
the emergency flashers are switched on by us
ing the turn signal lever. The emergency flash
ers stop temporarily .
T he emergency flashers also work when the
ign it ion is turned off .
T he emergency flashers w ill turn on a utomat i
ca lly if yo u are in an accident where the airbag
has deployed.
(D Tips
You sho uld turn on the emergency f lashers
when:
- yo u are the last veh icle standing in a t raf
fic jam so that any other vehi cles coming
can see you, or whe n
- your vehicle has bro ken down or you are
in an eme rgency s ituation, or when
- yo ur vehicle is be ing towed by a tow
truck or if you are tow ing another vehicle
beh ind you.
Page 56 of 286

54 Clear vision
Interior lights
Front/rear interior lights
Fig . 57 Fro nt headliner : interior lighting controls
Fig. 58 Rear headlin er: rear reading lights
@ Interior lights
Press the button ®· T he LED in the button il
luminates.
If the LED illum inates, the interior lights turn
on automatically when you un lock the vehicle,
open a door or remove the ignition key. The in
ter ior lights turn off several seconds after
your close the doors, when you lock the vehi
cle or when you turn the ignition on. When a
door is open, the light turns off after a few
minutes .
@ Front/rear reading lights
To turn a reading light on/off, press the but
ton~¢
fig. 57or ¢fig. 58.
Instrument illumination
The basic brightness of the illumination for
the instruments, the center console and the
display can be adjusted.
Fig. 59 Instrument illumination
.,. Press the knob to release it .
.,. Turn the knob toward"-" or"+" to reduce or
increase the brightness .
.,. Press the knob aga in to return it to its origi
nal position.
(!') Tips
The instrument illumination (for dials and
needles) lights on when the ignition is
switched on and the vehicle lights are
turned off. As the daylight fades, the illu
mination of the dia ls likewise dims auto
matically and will go out completely when
the outside light is very low. This feature is
meant to remind you to switch on the
headlights when outside light conditions
become poor.
Vision
Adjusting the exterior mirrors
Fig. 60 Forward section of driver's armrest: power mir
r or controls