2013 SSANGYONG KORANDO cluster

8010-01
2) TPMS Mode
(1) Supervision type LCD instrument cluster display
It monitors the tire and warns the driver if there is any abnormality.
The driver can see the current tire pressure by pressing the TRIP switch. -
-
Status Message Operating condition
Impossible to
determine tire
pressure
possible to determine tire pressure correctly
* At initial start, the tire pressure can be displayed
after 10 minutes of driving at speed of 20 km/h or
higher
Correct tire pressure The specified tire pressure is based on a cold tire
with the vehicle unloaded (no occupant); 32 psi at
Lower than minimum
tire pressureCorresponding status lamp comes on if tire
pressure is 24 psi or less
Excessive tire
pressureCorresponding status lamp blinks with shading
reverse at interval of 0.4 seconds if tire pressure is
50 psi or higher
Low tire pressure Corresponding status lamp comes on if tire
pressure is 24 psi or less
Sudden tire pressure
lossCorresponding status lamp blinks with shading
reverse at interval of 0.4 seconds if tire pressure
changes more than 3 psi per 1 minute at speed of 0
km/h or above.
Imbalance between
left and right tire
pressureCorresponding status lamps blink alternately at
interval of 1.0 second if tire pressure differs by more
than 4 psi in the left and right tires while driving for
more than 10 minutes

(2) Standard type LCD instrument cluster display
-
3) GSI(Gear Shift Indication)
Status Standard type Supervision type
Display gear
stage for
manual
transmission
Informs appropriate shift time for manual transmission
: This means that you should shift up to 3rd gear.
(2nd gear or lower currently)
: This means that you should shift down to 3rd gear.
(4th gear or higher currently)
The system operates normally when the indicator lamp looks not being gone out
completely.

8010-01
Status Supervision type
LCD display
The ESCL (Electric Steering Column Lock) is a device to lock the steering handle
using an electric signal, not a mechanical type and shows the messages above if the
relevant systems are faulty.
4) ESCL
5) LCD display
Status Old New
LCD display
Bar graph border maintained when adjusting illumination brightness
Average fuel economy and instant fuel economy displayed simultaneously
-
Auto cruise indicator and supervision cluster DOT LCD graphic added for gasoline
engine ? newly adopted ?
-
DOT LCD winter mode deleted

8010-01
1. OVERVIEW
There are two types in the instrument cluster used for KORANDO C: SVC (super vision) and STD
(standard). While the SVC type has three LCD screens - , and SEG LCD>, the STD type has one LCD screen.
2. LAYOUT
SVC
ODO SEG LCD
GAGE SEG LCDGAGE DOT

Low fuel level warning lamp
Warning lamp
(amber)
Engine overheat warning lamp
Warning lamp
(red)
Door ajar
Warning lamp
(red)
Seat belt reminder
Warning lamp
(red)
Air bag
Warning lamp
(red)
However, the fuel level may change slight depending on vehicle
condition, inclination of the road, etc. Also, it blinks if there is a short or
open circuit between the fuel level sensor and cluster.
interval of 1 second, a message is displayed, the warning sounds once
through the speaker and the buzzer sounds at an interval of 0.5 seconds.
This lamp comes on when any door is open or not closed completely.
(both STD and SVC class)
This lamp comes on when the ignition switch is pressed ON.
It keeps coming on if the driver's seat belt is not fastened.
This lamp comes on when the ignition switch is pressed to the ON mode.
Then, it goes off if the system is normal.
If this lamp stays on while driving, it means that the air bag system is faulty.

Indicator
(green)
Passenger seat belt reminder
Left turn signal indicator
Right turn signal indicator
Indicator
(red)
Indicator
(green)
Indicator
(green)
Winter mode indicator(DSL only)
The right turn signal indicator blinks if the light switch is pushed up to
the right, and both turn signal indicators blink if the hazard warning flasher
switch is pressed.
When the mode switch is pressed, the winter mode is selected and the
winter mode indicator comes on on the instrument cluster. The winter
mode is used to start off on a slippery road with the 2nd gear. If the switch
is pressed again, the winter mode is deactivated and system returns to
standard mode.This indicator comes on when the ignition switch is turned to the "ON"
position and goes off when the passenger's seat belt is fastened.
The left turn signal indicator blinks if the light switch is pushed down to the
left, and both turn signal indicators blink if the hazard warning flasher switch
is pressed.
Smart key warning lamp
Indicator
(amber)
This lamp comes on when the uncertified transponder or smart key is
detected,
SKM system is defective or there is no smart key in the vehicle.

8010-01
SVC class instrument cluster STD class instrument cluster
(4) Illumination Mode
TRIP/RESET switch
Press for less than 1 second: change to next mode
Press for more than 1 second:
: Enter into illumination level mode
1 second on consecutively illumination mode
If the Trip/Reset switch is not pressed within 3 seconds after getting into the illumination mode, the
LCD changes to next mode. -
-
-

(5) TPMS mode
The TPMS (Tire Pressure Monitoring System) monitors each tire's status and warns a driver for
dangerous situations.
At initial start (more than 20 minutes have elapsed after ignition off), the tire pressure is not
determined. It can be displayed after 10 minutes of driving at speed of 20 km/h or higher. -
-
Standard type
Pressing the TRIP switch at the illumination brightness mode shows the items in the following order:
TPMS (front)->TPMS (rear).
Status Operating conditions Display
Tire pressure
displayAt initial start (more than 20 minutes have
elapsed after ignition off), the tire pressure is
not determined. It can be displayed after 10
minutes of driving at speed of 20 km/h or
higher.
FR - display
RR - displayIf the tire pressure is abnormal when it is not
The standard type instrument cluster shows

8) Buzzer
Specifications
Function Signal
Part name PKM17EPP-2002-B0 (MURATA, Piezoelectric Sound Components)
Permitted input voltage 25 VP-P or less
Operating temperature
Storage temperature
Sound pressure level 70 dB/min (3 Vp-p, 2 kHz, square wave, 10 cm)
Capacitance
Priority of instrument cluster buzzer output
If there are multiple signals at a time, the operation should be completed by the priority.
Priority
ItemBuzzer output
time
Operating condition
ON OFF
1 PAS See PAS
2 ESP 0.1sec 0.1secInstrument cluster buzzer output signal is
received from ABS/ESP
3Engine overheat
warning lamp0.5sec 0.5sec
4Water separator
warning light0.5sec 0.5secWater separator warning light ON with
IGN ON
5 Parking brake 2.8sec 1.5secParking brake applied depending on
vehicle speed