2013 MITSUBISHI L200 Owner's Manual (in English)

L (Genuine part information) Genuine parts No.ECE No.*1MZ314393E1-04301146*2MZ314509 #2E1-04301146*3MZ313045E1-04301133*4MZ314451E1-04301203*5MZ314250E1-04301169
#2
: To be available in the middle of 2012
NOTE l There is no applicable MITSUBISHI MOTORS Genuine Parts to the Mass Group “0-Up to 10 kg”.

MITSUBISHI MOTORS Europe B.V. reserves the right to changes without any prior announcement.
For further information, please contact a MITSUBISHI MOTORS Authorized Service Point.
Single cab (Bench seat)
Mass group
Seating positionFront passengerFront centreActivated airbagDeactivated airbag #10- Up to 10 kgXXX0+- Up to 13 kgXL*1
, L* 2XI-9 to 18 kgXL*3
, L* 4XII-15 to 25 kgXL*5XIII-22 to 36 kgXL*5X
#1
: With front passenger’s airbag deactivated by means of front passenger’s airbag ON-OFF switch.
Seat and seat belts
2-19
OKTE13E1
2

CAUTIONlWhen installing a child restraint system, prevent the head restraint from touching the child restraint system by removing it or adjusting its height.Key of letters to be inserted in the table above:
lL- Suitable for particular child restraints in the following list (MITSUBISHI MOTORS genuine parts).
l X- Seat position not suitable for children in this mass group.
L (Genuine part information) Genuine parts No.ECE No.*1MZ314393E1-04301146*2MZ314509 #2E1-04301146*3MZ313045E1-04301133*4MZ314451E1-04301203*5MZ314250E1-04301169
#2
: To be available in the middle of 2012
NOTE l There is no applicable MITSUBISHI MOTORS Genuine Parts to the Mass Group “0-Up to 10 kg”.

MITSUBISHI MOTORS Europe B.V. reserves the right to changes without any prior announcement.
For further information, please contact a MITSUBISHI MOTORS Authorized Service Point.
Seat and seat belts
2-20 OKTE13E1
2

Club cab
Mass group
Seating positionFront passengerRear outboardActivated airbagDeactivated airbag#10- Up to 10 kgXXX0+- Up to 13 kgXL*1
, L* 2L*1
, L* 2I-9 to 18 kgXL*3
, L* 4L*3
, L* 4II-15 to 25 kgXL*5XIII-22 to 36 kgXL*5X
#1
: With front passenger’s airbag deactivated by means of front passenger’s airbag ON-OFF switch.
CAUTIONl When installing a child restraint system, prevent the head restraint from touching the child restraint system by removing it or adjusting its height.Key of letters to be inserted in the table above:
lL- Suitable for particular child restraints in the following list (MITSUBISHI MOTORS genuine parts).
l X- Seat position not suitable for children in this mass group.
L (Genuine part information) Genuine parts No.ECE No.*1MZ314393E1-04301146*2MZ314509 #2E1-04301146*3MZ313045E1-04301133*4MZ314451E1-04301203*5MZ314250E1-04301169
#2
: To be available in the middle of 2012
Seat and seat belts
2-21
OKTE13E1
2

NOTEl There is no applicable MITSUBISHI MOTORS Genuine Parts to the Mass Group “0-Up to 10 kg”.

MITSUBISHI MOTORS Europe B.V. reserves the right to changes without any prior announcement.
For further information, please contact a MITSUBISHI MOTORS Authorized Service Point.Double cab
Mass group
Seating positionFront passengerRear outboardRear centreActivated airbagDeactivated airbag #10- Up to 10 kgXXUX0+- Up to 13 kgXL*1
, L* 2U, L* 1
, L* 2XI-9 to 18 kgXL*3
, L* 4U, L* 3
, L* 4L*3II-15 to 25 kgXL*5U, L* 5L*5III-22 to 36 kgXL*5U, L* 5L*5
#1
: With front passenger’s airbag deactivated by means of front passenger’s airbag ON-OFF switch.
CAUTIONl When installing a child restraint system, prevent the head restraint from touching the child restraint system by removing it or adjusting its height.Key of letters to be inserted in the table above:
lU- Suitable for “universal” category restraints approved for use in this mass group.
l L- Suitable for particular child restraints in the following list (MITSUBISHI MOTORS genuine parts).
l X- Seat position not suitable for children in this mass group.
Seat and seat belts
2-22
OKTE13E1
2

L (Genuine part information) Genuine parts No.ECE No.*1MZ314393E1-04301146*2MZ314509 #2E1-04301146*3MZ313045E1-04301133*4MZ314451E1-04301203*5MZ314250E1-04301169
#2
: To be available in the middle of 2012
NOTE l There is no applicable MITSUBISHI MOTORS Genuine Parts to the Mass Group “0-Up to 10 kg”.

MITSUBISHI MOTORS Europe B.V. reserves the right to changes without any prior announcement.
For further information, please contact a MITSUBISHI MOTORS Authorized Service Point.
Seat and seat belts
2-23
OKTE13E1
2

Child restraint anchorage points (Dou-
ble cab)* E00406900354
Anchorage locations
There are 2 child restraint anchorage points on the
floor, located behind the rear seat. These are for se-
curing a child restraint system tether strap to each
of the 2 rear seating positions in your vehicle.
*: Rear of the vehicle
CAUTIONl The anchorages are only applicable for
child restraints fitted in the rear seat.Tether anchorage strap installationWARNINGl Child restraint anchorages are designed
to withstand only those loads imposed by
correctly fitted child restraints. Under no
circumstances are they to be used for
adult seat belts, harnesses, or for attach-
ing other items or equipment to the vehicle.
1. Remove the head restraint from the location
in which you wish to install a child restraint.
2. Drop the child restraint’s tether strap (A)
down the back of the rear seatback.
3. Tip the armrest forward. Open the fastener
(B) that is located in the space where the arm-
rest was stowed.
4. Put your hand in the opening of the fastener,
attach the tether strap’s hook (C) to the tether
anchorage (D), and securely tighten the teth-
er strap.
Seat and seat belts
2-24 OKTE13E1
2

Installing a child restraint system to
the lower anchorage (ISOFIX child re-
straint mountings)* E00408900114
Your vehicle’s second seat is fitted with lower an-
chorages for attaching a child restraint system with
ISOFIX mountings.Child restraint system with ISOFIX
mountings E00409000561
The child restraint system is designed only for
seats that incorporate lower anchorages. Retain the
child restraint system using the lower anchorages.
It is not necessary to retain the child restraint sys-
tem using the vehicle’s seat belts.
A- Child restraint system connectors
To install
WARNINGl If there is any foreign material in or
around the connectors, remove it before
installing the child restraint system. Also,
make sure the seat belt is away from, not
looped through or otherwise interfering
with, the child restraint system. If foreign
matter is not removed and/or the seat
belt interferes with the child restraint sys-
tem, the child restraint system will not be
secured properly and could move for-
ward in the event of sudden braking or a
collision, seriously injuring the child and
possibly other vehicle occupants.
l When the vehicle is moving do not adjust
the seat where the child restraint system
is installed.1. Push the child restraint system’s connectors
into the lower anchorages (A) in accordance
with the instructions provided by the child re-
straint system’s manufacturer.CAUTIONl When installing a child restraint system,
prevent the head restraint from touching
the child restraint system by removing it
or adjusting its height.
If your child restraint system requires the use
of a tether strap, fasten the tether strap in ac-
cordance with steps 2 through 5. If a tether
strap is unnecessary, perform the step 6.
2. Remove the head restraint from the location
in which you wish to install a child restraint.
Seat and seat belts
2-25
OKTE13E1
2

3.Drop the child restraint’s tether strap (B)
down the back of the rear seatback.
4. Tip the armrest forward. Open the fastener
(C) that is located in the space where the arm-
rest was stowed.
5. Put your hand in the opening of the fastener,
attach the tether strap’s hook (D) to the teth-
er anchorage (E), and securely tighten the teth-
er strap.
6. Push and pull the child restraint system in all
directions to be sure it is firmly secured.
To remove
Remove the child restraint in accordance with the
instructions provided by the child restraint sys-
tem’s manufacturer.
Installing a child restraint system to a
3-point type seat belt (with emergency
locking mechanism) E00408700705Single cab and Club cabDouble cabFront passenger seatFront passenger seat
Installation:
1.Fasten the seat belt to secure the child re-
straint system.
Make sure you hear a “click” when you in-
sert the latch plate in the buckle.
CAUTIONl When installing a child restraint system,
prevent the head restraint from touching
the child restraint system by removing it
or adjusting its height.
2. Remove all slack by using the locking clip.
Seat and seat belts
2-26 OKTE13E1
2