2013 Lexus IS300h Owner's Manual

4837-3. Do-it-yourself maintenance
7
Maintenance and care
IS300h_EE(OM53B95E)
Front turn signal lights (vehicles with discharge headlights)
To ensure enough space to per-
form work, turn the steering
wheel to rotate the front wheel
away from the bulb to be
replaced.
Remove the 2 fender liner
clips.
Turn the steering wheel to the left
when replacing the right side light
bulb, and turn the steering wheel
to the right when replacing the
left side light bulb.
To take out the lower clip, turn
the head of the clip to unlock it,
then remove it by pulling.
Unfasten the clamp, and pull
back the fender liner.
When unfastening the clamp,
wrap the tip of the screwdriver
with tape to protect the vehicle
from damage.
Turn the bulb base counter-
clockwise.
1
2
3

4847-3. Do-it-yourself maintenance
IS300h_EE(OM53B95E)
Remove the light bulb.
Install a new light bulb then
install the bulb base to the
light unit by inserting it and
turning the bulb base clock-
wise.
After installing the light bulb,
turn on the front turn signal light
to visually check that there is no
light leaking from the bulb base.
Reinstall the fender liner, fas-
ten the clamp and install the 2
clips.
Install the lower clip by inserting
it with the clip groove held verti-
cally straight.
4
5
6

4857-3. Do-it-yourself maintenance
7
Maintenance and care
IS300h_EE(OM53B95E)
Front turn signal lights (vehicles with LED headlights)
For the left side only: Pinch
the clip to remove the washer
fluid filler opening.
Turn the bulb base counter-
clockwise.
Remove the light bulb.
Install a new light bulb then
install the bulb base to the
light unit by inserting it and
turning the bulb base clock-
wise.
After installing the light bulb,
turn on the front turn signal light
to visually check that there is no
light leaking from the bulb base.
After replacing the left side bulb, install the washer fluid filler open-
ing to its original position.
1
2
3
4
5

4867-3. Do-it-yourself maintenance
IS300h_EE(OM53B95E)
Rear turn signal lights
Open the trunk, and remove
the 2 covers and 2 screws.
When removing the cover, wrap
the tip of the screwdriver with
tape to protect the vehicle from
damage.
Push and pull the light unit
toward the rear of the vehicle
as shown in the illustration to
remove it.
Apply protective tape to the
peripheral of the light unit instal-
lation surface on the vehicle body,
such as the rear bumper, to protect
the vehicle from damage.
Pushing on the portion A in the
illustration toward the rear of the
vehicle will make disengagement
of the tabs easier.
Turn the bulb base counter-
clockwise.
Remove the light bulb.
1
2
3
4

4877-3. Do-it-yourself maintenance
7
Maintenance and care
IS300h_EE(OM53B95E)
Install a new light bulb then
install the bulb base to the
light unit by inserting it and
turning the bulb base clock-
wise.
After installing the light bulb,
turn on the rear turn signal light to
visually check that there is no
light leaking from the bulb base.
Align the tabs and push the
light unit toward the front of
the vehicle to install it.
Remove the protective tape
applied to the peripheral of the
light unit installation surface on
the vehicle body.
Install the 2 screws and 2 covers.
5
6
7

4887-3. Do-it-yourself maintenance
IS300h_EE(OM53B95E)
Back-up light
Open the trunk, remove the 3
clips on the side which the
bulb is to be replaced and pull
back the trunk lid cover.
Turn the bulb base counter-
clockwise.
Remove the light bulb.
Pull out the connector carefully,
ensuring that excessive pulling
load is not applied to the wire har-
ness.
Install a new light bulb then
install the bulb base to the
light unit by inserting it and
turning the bulb base clock-
wise.
After installing the light bulb,
turn on the back-up light to visu-
ally check that there is no light
leaking from the bulb base.
Reinstall the trunk lid cover with the 3 clips.
To install the clips, simply push them in.
1
2
3
4
5

4897-3. Do-it-yourself maintenance
7
Maintenance and care
IS300h_EE(OM53B95E)
Outer foot lights
Press the upper part of the out-
side rear view mirror to tilt the
mirror face upward, and apply
protective tape to the lower
part of the mirror cover.
Insert 2 flathead screwdrivers
wrapped in protective tape,
and disconnect the tabs behind
the mirror.
Pry the mirror out toward you,
disconnecting the tabs 2 at a time.
Work carefully, ensuring that you
do not drop the mirror.
Disconnect the connectors
behind the mirror, and remove
the mirror.
When removing the thin connec-
tors, make sure to mark one of the
connectors with a piece of tape, to
avoid mixing them up when rein-
stalling.
Work carefully, ensuring that you
do not drop the mirror.
When handling the mirror, do not
touch the parts applied with
grease.
The number of connectors
equipped differs by vehicle speci-
fication.
1
2
3

4907-3. Do-it-yourself maintenance
IS300h_EE(OM53B95E)
Remove the 5 screws and take
off the mirror’s outer cover
and the cover behind the mir-
ror.
Turn the bulb base counter-
clockwise.
Remove the light bulb.
Install a new light bulb then
install the bulb base to the
light unit by inserting it and
turning the bulb base clock-
wise.
When inserting the socket, align
the marks printed on the light
body and the socket.
4
5
6
7