Page 132 of 284
Driving
130
) Select position M.
To engage reverse gear R, the vehicle must be
immobilised with your foot on the brake pedal.
)Select position R.
At very low speed, if reverse gear is requested,
this will only be acted on when the vehicle is
immobilised.
At high speed, if reverse gear is requested,
the N indicator flashes and the gearbox goes into neutral. To engage a gear again, put the gear lever in position A
or M.
Te m p o r a ry control of gear changing
You can temporarily take over control of gear changing using the "+"
and "-"
steering mounted paddles: if the engine speed allows,
the request to change gear is acted on.
This function allows you to anticipate cer tain situations such as over taking a vehicle or theapproach to a corner.
After a few moments without any action on
the control paddles, the gearbox resumes automatic control of the gears.The
gears engaged appear in
succession in the instrument panel screen.
The
gear change requests are only acted on if
the engine speed permits.
It is not necessary to release the accelerator
during gear changes.
When brakin
g or slowing down, the gearbox changes down automatically to allow the
vehicle to accelerate in the correct gear.
On sharp acceleration, the gearbox will not change up unless the driver acts on the gear lever or the steering mounted paddles.
Never select neutral Nwhile the vehicle is moving.
You can change mode at any time, bemoving the gear lever from Mto A
or the other way round.
Engagement of reverse gear isaccompanied by an audible signal.
Manual mode
Reverse
Page 133 of 284
9
Driving
131
Stopping the vehicle Operating fault
With the ignition on, the flashing of AUTO,accompanied by an audible signal and a
message in the screen, indicates a malfunction
of the gearbox.
Have it checked by a CITROËN dealer or aqualified workshop.
In all cases when parking, you mustapply the parking braketo immobilise the vehicle.
When immobilising the vehicle, with theengine running, you must place the gear lever in neutral N.
Before carrying out any work in theengine compar tment, ensure that thegear lever is in neutral Nand that theparking brake is applied. Be
fore switching off the engine, you can:
- move to position Nto engage neutral,
or
- leave the gear engaged; in this case, it will not be possible to move the vehicle.
Page 134 of 284
Driving
132
Hill start assist
(with the 6-speed
electronic gearbox
system)
System which holds your vehicle temporarily (approximately 2 seconds) when star ting on a slope, the time it takes to move your foot from
the brake pedal to the accelerator pedal.
This function is onl
y active when:
- the vehicle is completely stationary, withyour foot on the brake pedal,
- certain conditions on a slope are met,
- with the driver’s door closed.
The hill start assist function cannot bedeactivated. On an ascendin
g slope, with the vehiclestationary, the vehicle is held momentarily
when you release the brake pedal:
- provided you are in automated mode (position A) or in manual mode (position AM)on an electronic gearbox.On a descendin
g slope, with the vehicle
stationar y and reverse gear engaged, the
vehicle is held momentarily when yourelease the brake pedal.
Operating fault
If a malfunction of the system occurs, these
warning lamps come on. Contact a CITROËN
dealer or a qualified workshop to have thesystem checked.
Do not leave the vehicle while it is being held in the hill star t assist phase.If you need to leave the vehicle with the engine running, manually applythe parking brake then ensure that theparking brake warning lamp is on (notflashing) in the instrument panel.
Operation
Page 135 of 284
9
Driving
133
Stop & Start
The Stop & Star t system puts the engine temporarily into standby - STOP mode - during stops in the traffic (red lights, traffic jams, or other...). The engine restarts automatically - START mode - as soon as you want to move off. The restar t takes place instantly, quickly and silently.
Per fect for urban use, the Stop & Star t system reduces fuel consumption and exhaust emissions as well as the noise level when stationary.
Operation
Going into engine STOP mode
The "ECO"warning lamp comes
on in the instrument panel and the
engine goes into standby:
- with the 6-speed electronic
gearbox
system, at speeds below 5 mph (8 km/h),
when you press the brake pedal or put thegear lever in position N.
A time counter calculates the sum
of the periods in STOP mode
during a journey. It rests itself
to zero every time the ignition isswitched on with the key.
Special cases: STOP mode notavailable
STOP mode is not invoked when:
- the driver's door is open,
- the driver's seat belt is not fastened,
- the vehicle has not exceeded 6 mph (10 km/h) since the last engine star t using
the key,
- the engine is needed to maintain acomfor table temperature in the passenger compartment,
- demisting is active,
- some special conditions (battery charge,
engine temperature, braking assistance,
ambient temperature...) where the engine isneeded to assure control of a system.
The "ECO"
warning lamp flashes for a few seconds then goes off.
This operation is per fectly normal
.
Never refuel with the engine in STOPmode; you must switch off the ignition with the key.
For your comfor t, during parking manoeuvres, STOP mode is not available for a few seconds after coming out of reverse gear.STOP mode does not affect the functionality of the vehicle, such as for example, braking, power steering...
Page 136 of 284
Driving
134
Going into engine START mode
The "ECO"warning lamp goes
off and the engine star ts with the electronic gearboxsystem:
- gear lever in position Aor M
, when yourelease the brake pedal,
- or gear lever in position Nand the brake pedal released, when you move the gear lever to position A
or M,- or when you engage reverse gear.
Special cases: START invoked
automatically
For reasons of safety and for your comfort,START mode is invoked automatically when:
- you open the driver's door,
- you unfasten the driver's seat belt,
- the speed of the vehicle exceeds 7 mph(11 k m/h) with the electronic gearbox system,
- some special conditions (battery charge,engine temperature, braking assistance,
ambient temperature...) where the engine is
needed for control of a system.
Th
e "ECO"
warning lamp flashes for
a
few seconds, then goes off.
This operation is per fectly normal.
Deactivation
At any time, press the "ECO OFF"
switch todeactivate the system.
This is confirmed by the switch warning lampcoming on accompanied by a message in the screen.
If the system has been deactivatedin STOP mode, the engine restartsimmediately.
Page 137 of 284
9
Driving
135
Operating fault
In the event of a fault with the system, the
"ECO OFF"
switch warning lamp flashes thencomes on continuously.
Have it checked by a CITROËN dealer or aqualified workshop.
In the event o
f a fault in STOP mode, the
vehicle may stall. All of the warning lamps in the instrument panel come on. It is thennecessary to switch off the ignition and star t
the engine again using the key.
Maintenance
This system requires a battery with a specialspecification and technology (reference
numbers available from a CITROËN dealer or a
qualified workshop).
Fitting a battery not listed by CITROËN
introduces the risk of malfunction of the system.
Before doing anything under the bonnet,deactivate the Stop & Star t system toavoid any risk of injury resulting fromautomatic operation of STA R T m o d e .
The Stop & Star t system makes use of advanced technology. All workon this type of battery must be doneby a CITROËN dealer or a qualifiedworkshop.
Press the "ECO OFF"switch again.
The system is active again; this is con
firmed
by the switch warning lamp going off,
accompanied by a message in the screen.
The system is reactivated automatically at every new star t using the key.
Reactivation
Page 143 of 284
9
Driving
141
Deactivation Reactivation
With the engine running, press button A
todeactivate the system permanently. Theindicator lamp in the button comes on.
The system will be deactivated automatically when towing a trailer or when a bicycle carrier is fitted (vehiclefitted with a towbar or bicycle carrier recommended by CITROËN).
In bad or wintry weather, ensure that the sensors are not covered with mud,frost or snow.
Press button Aagain to reactivate the system.
The indicator lamp in the button goes o
ff.
If there is an operating fault, when reverse gear is engaged, the ser vice warning lamp comes
on, accompanied by an audible signal (short
beep) and a message in the multifunction screen.
Page 146 of 284
Checks
144
Bonnet
)
Push the exterior safety catch B
to the leftand raise the bonnet.
)
Unclip the stay C
from its housing. )
Fix the stay in the notch to hold the bonnet open.
Closing
)Take the stay out of the support notch. )Clip the stay in its housing. )Lower the bonnet and release it at the end of its travel. )Pull on the bonnet to check that it is secured correctly.
)Open the front left door. )Pull the interior bonnet release lever A , located at the bottom of the door aper ture.
Opening
Before doing anything under the bonnet,
switch off the Stop & Star t system toavoid any risk of injury resulting from anautomatic change to START mode.
The location of the interior bonnetrelease lever prevents opening of the bonnet while the front left door is closed.
Do not open the bonnet in high winds.
When the engine is hot, handle theexterior safety catch and the bonnet stay with care (risk of burns).
