2013 Citroen C3 ignition

11
Practical information
145

Repair procedure


1. Sealing
)
Uncoil the white pipe G
fully.)
Unscrew the cap from the white pipe.)
Connect the white pipe to the valve of the
tyre to be repaired.

)
Connect the compressor's electric plug to
the vehicle's 12 V socket. ) Star t the vehicle and leave the engine
running.
Take care, this product is harmful(e.g. ethylene-glycol, colophony...) if
swallowed and causes irritation to the eyes. Keep this product out of the reach of children.
Avoid removing any foreign bodieswhich have penetrated into the tyre.

Do not star t the compressor before connecting the white pipe to the tyre valve: the sealant product would beexpelled through the pipe.
)Switch off the ignition.

)Turn the selector A
to the
"sealant" position. )Check that the switch B is in position "O"
.

Practical information
152
Removing a wheel

List of operations
)Remove the bolt cover from each of the bolts using the tool 3(with alloy wheels
only). )Fit the security bolt socket 4 on thewheelbrace 1to slacken the security bolt(if your vehicle has them).)Slacken the other bolts using the
wheelbrace 1only.
Parking the vehicle
Immobilise the vehicle where it does not block traffic: the ground must be level, stable and not slippery. Apply the parking brake, switch off theignition and engage first gear *
to lock the wheels. If necessary, place a chock under the wheel diagonally opposite the wheel tobe changed. It is imperative that you ensure that the occupants get out of the vehicle and wait where they are safe.Never go underneath a vehicle raisedusing a jack; use an axle stand.

*
position Rfor an electronic gearbox; position Pfor an automatic gearbox.

Practical information
166
Fuse N°RatingFunctions
F8
20 A
Multifunction screen, audio system, navigation and audio system, instrument panel with clock, alarm control unit, alarm siren, audio system (after-market), 12 V socket, portable
navigation carrier power supply.
F
930 A Multifunction screen, audio s
ystem, navigation and audio system, instrument panel with clock, alarm control unit, alarm siren, audio system (after-market), 12 V socket, portable
navigation carrier power supply, locking.
F1
015 A Steering mounted controls.
F1
115 A
Ignition, diagnostic socket, automatic gearbox control unit.
F12 15 A
Rain
/ sunshine sensor, trailer relay unit, driving school module.
F13 5
A Main stop switch, engine relay unit, gear lever for electronicgearbox.
F1415 A Parking sensors control unit, airbag control unit, instrument
panel, digital air conditioning, USB Box, HiFi amplifier,
reversing camera.
F1
530 A Locking.
F1
6- Not used.
F17
40 A Rear screen and door mirrors demisting/defrosting.
S
H- PA RC shunt.

Practical information
168
Fuse table
Fuse N°RatingFunctions
F120 AEngine control unit supply, cooling fan unit control relay, multifunction engine control main relay, injection pump (Diesel).
F
215 AHorn.
F
310 AFront / rear wash-wipe.
F420 ADaytime running lamps, LED daytime running lamps.
F
515 ADiesel heater (Diesel), par ticle filter additive pump (Diesel), air
flow sensor (Diesel), fuel pump (1.1i and 1.4i), blow-by heater and electrovalves (VTi).
F
610 A ABS/ESP control unit, secondary brake lamp switch.
F710 AElectric power steering, automatic gearbox.
F
825 AStarter motor control.
F9
10 ASwitching and protection unit (Diesel).
F10
30 AFuel heater (Diesel), blow-by heater (1.1i, 1.4i and Diesel),fuel pump (VTi), injectors and ignition coils (petrol), electronic
thermostat and canister purge electrovalve (1.1i and 1.4i).
F1
140 AHeater blower.

11
Practical information
169
Fuse N°RatingFunctions
F1230 A Windscreen wipers slow / fast speed.
F1
340 A Built-in systems inter face supply (ignition positive).
F14
30 A Valvetronic supply (VTi).
F1
510 A Right-hand main beam headlamps.
F1
610 A
Left-hand main beam headlamps.
F17 15 A
Left-hand dipped beam headlamps.
F18 15 A
Ri
ght-hand dipped beam headlamps.
F1
915 A Oxygen sensors and electrovalves (VTi), electrovalves (Diesel),
EGR electrovalve (Diesel).
F20 10 A Pumps, electronic thermostat
(VTi), water in fuel sensor (Diesel).
F2
15 A Fan assembly control supply, ABS/ESP.

Practical information
172

Starting using another
batter
y

Charging the battery using
a battery charger
When the battery on your vehicle is discharged,
the engine can be star ted using a slave battery (external or on another vehicle) and jump leads.
)Follow the instructions for use provided by
the manufacturer of the charger.
First check that the slave battery has a nominalvoltage of 12 V and a capacity at least equal to
that of the discharged battery.
Do not try to star t the engine by connecting a
batter
y charger.
Do not disconnect the (+) terminal when the engine is running.
)Connect the red cable to the positive
terminal (+) of the flat battery A , then to the positive terminal (+) of the slave battery B.)Connect one end of the green or blackcable to the negative terminal (-) of the
slave battery B(or ear th point on the other
vehicle).)Connect the other end of the green or black cable to the negative terminal C (or
the engine mounting) of the broken-down
vehicle.)Star t the engine of the other vehicle and
allow it to run for a few minutes.
Do not disconnect the battery to charge it.
)
Operate the star ter of the broken-down
vehicle and let the engine run.
If the engine does not star t immediately,switch off the ignition and wait a few
moments before trying again.) Wait until the engine returns to idle, then
disconnect the jump leads in reverse order.


Batteries contain harmful substances such as sulphuric acid and lead. They must bedisposed of in accordance with regulations and must not, in any circumstances, be discarded with household waste.
Take used remote control batteries andvehicle batteries to a special collection
point.

11
Practical information
175








Changing a front or rear wiper blade


Removal
)Raise the corresponding wiper arm.)Unclip the wiper blade and remove it.
Fitting
)
At the front, check the size of the wiper blade as the shorter blade is fitted to the
passenger side of the vehicle.) Put the corresponding new wiper blade in
place and clip it.
) Fold down the wiper arm carefully.


Before removing a front
wi
per blade
)Within one minute after switching off the
ignition, operate the wiper stalk to position
the wiper blades in the ver tical position.

This position must be used in order to avoid damaging the wiper blade and the bonnet.
After fitting a front wiper
blade
) Switch on the ignition. )
Operate the wiper stalk again to park the
wiper blades.
Procedure for replacin
g a worn wiper blade with a new one without the use of tools.

11
Practical information
177

To w i ng your vehicle
)On the front bumper, unclip the cover bypressing at the bottom. )Screw the towing eye in fully. )Install the towing bar. )Place the gear lever in neutral (position N
for an electronic or automatic gearbox).
) On the rear bumper, unclip the cover bypressing at the bottom. )
Screw the towing eye in fully. )
Install the towing bar. )
Switch on the hazard warning lamps on both vehicles.)
Move off gently and drive for a shor t distance only.



To w i ng another vehicle
Failure to obser ve this special condition could result in damage to cer tain components (braking, transmission...) and the absence of braking assistance the next time the engine is star ted.
)
Unlock the steering by turning the key one
notch in the ignition switch and release the
parkin
g brake. ) Switch on the hazard warning lamps onboth vehicles. )
Move off gently and drive for a shor t
distance only.