2013 AUDI TT light

CD Note
-Avoid high engine speeds, fast accelera­
tion or heavy engine loads whi le the en­
gine is still cold. This could damage the
engine.
- The engine cannot be started by pushing or towing the veh icle.
@) For the sake of the environment
To avoid unnecessary engine wear and to
reduce exhaust emissions, do not let your
veh icle stand and warm up. Be ready to
drive off immediately after starting your
veh icle. Maintain moderate speed until the
eng ine is completely warm . Remember,
the engine performs best at operating
temperature .
Stopping the engine
~ Turn the ign ition key to position @
~page 71, fig. 71.
_& WARNING
-Never turn off the engine before the ve­
hicle has come to a complete stop. The
full function of the brake booster and the
power steering is not guaranteed . You
must use more force to turn or brake if
necessary. Because you cannot steer and
brake as you usually would, this could
lead to crashes and serious injur ies.
- The radiator fan can continue to run for
up to 10 minutes even after you have
turned
off the engine and removed the
ignition key . The radiator fan can also
turn on again if the engine coolant heats
up because of intense sunlight or heat
build-up in the engine compartment.
CD Note
Do not stop the engine immed iate ly after
hard or extended driving. Keep the engine
running for approximately two minutes to
prevent excessive heat build-up.
On the road 73
Parking brake
Parking brake
When the parking brake is set, it prevents the
vehicle from rolling away unintentionally .
Fig. 72 Center console: Parki ng b rake set
Setting the parking brake
~ Pull the park ing brake lever all the way up.
Releasing the parking brake
~ Pull the parking brake lever up slightly and
press the release button at the same time
~ fig. 72 -arrow-.
~ Keep the release button pressed and lower
the parking brake~&_ .
If you should drive
off with the parking brake
still set, a warning tone will sound and the
follow ing will appear in the instrument clus­
ter to rem ind you to release the parking
brake:
Handbrake is applied
The parking brake warning comes on only af­
ter you have driven for longer than 3 seconds
and faster than 5 mph (5 km/h) .
The parking brake warning light_
(USA)/ . (CON) illuminates when the park­
ing brake is set and you switch on the ignition .
A WARNING
Always re lease the park ing brake com -
pletely. A partially engaged brake will
overheat the rear brakes, reduce their ef­
fectiveness and cause excessive wear. This
could lead to brake failure and an accident. .,.

76 On the road
Speed warning 2: setting a speed limit
Switches in the wiper arm are used to operate
warning threshold
2 .
'----I ®
Fig. 74 Wiper lever: Tr ip computer con trols
To store maximum speed
> Turn off the ignit ion.
> Briefly press the button in the instrument
cl uster ¢
page 75, fig. 73. The odometer
and the digital clock are now illuminated .
> Press the button for at least 2 seconds. The
currently stored maximum speed appears in
the display
or the crossed out symbol for
warning threshold 2, if no max imum speed
was set previously.
> Press the function selector sw itch in the
wipe r lever @¢
fig. 74 up or down to
change the set value. Values run up or dow n
i n steps of 6.2 mph (10 km/h).
To delete maximum speed
> Turn off the ignit ion .
> Briefly press the button in the instrument
cluster ¢
page 75, fig . 73. T he odometer
and the digital clock are now illumi nated.
> Press the button for at least 2 seconds . Th e
cu rrently stored maxim um speed appears in
the display.
> Press the reset button in the wiper lever ®
¢fig . 74 until the crossed out speed warn­
ing symbol for warning threshold 2 appears
i n the display.
A few seconds after the adjustment is com­
pleted, the illumination for the odometer and
the dig ital clock will go out.
(D Tips
This warning threshold can a lso be con­
trolled thro ugh the tr ip computer
¢ page 25, Navigating the menu.
Cruise control
Switching the system on
The cruise control system makes it possible to
drive at a constant speed starting at 20 mph (30 km/h) .
®-
Fig. 75 Contro l leve r with set b utton
Fig. 76 D isplay : Se lecte d speed
> Pull the lever to position (D ¢ fig. 75 to
switch the system on.
> Dr ive at the speed you w is h to set.
> Press button @ to set that speed.
.., ....
i
The display ¢ fig. 76 will show the set speed .
The display may vary depending on the type of
display in your vehicle. The indicator light
M;ll)~14 (US model)/ . (Canadian model) will
also light up in the instrument cluster .
A WARNING
- Always pay attention to traffic even when
the cruise control is switched on. You are
always responsib le for your speed and

78 On the road
Audi magnetic ride
Applies to vehicles: with mag netic r ide
Damping can be adjusted to the driver's pref­
erence and it adapts automatically to the cur­
rent driving situation.
Fig. 77 Cente r console: Switch for Audi magnetic r ide
.,. Press the switch ~ fig . 77 to turn spo rt set-
t ing o n or off.
Aud i magnetic ride is an electron ically con­
trolled damp ing system . Th is chassis system
assists the driver by adapting to the par ticular
situatio n th rough imper cep tible con trol p roc­
esses. The
damping provides individual mod u­
l ation of damping forces. For example, with
dampi ng cha racterist ics set to p rovide greater
comfort, damping is set somewhat harder for
a brief period only as required, when rounding
a curve and when braking.
Standard setting
Select the standard sett ing if you prefer a sus­
pension setting emphasizing comfort.
Sport setting
Select the sport setti ng if you prefe r a sporty
suspe nsio n setting . The LED in the sw itch
8
comes on to indicate spo rt setting .
@ Tips
The w arning/indicator light 8 in the in stru ­
ment cluster comes on in the even t of a
malfunction . Drive to the closest au thor ­
ized Audi dealer as soon as possible and
have the malfunction repaired.
Sport mode
Applies to vehicles: wit h Sport but ton
F ig . 7 8 Button in th e ce nte r console
.,. To switch sport mode on, press the button
in th e cente r console. The indicator light
t ur ns on .
.,. To swi tch spor t mo de off, press the bu tto n
in the center co nsole again. The indicator
light turns on .
A mo re agile and spo rty d riv in g style is po ssi­
ble when driving the vehicle in "sport mode".
T his mode affec ts thrott le response and the
sound of the engine and the damping charac ­
teristics of the Audi magnetic ride for dynamic
s uspension tuning .
@ Tips
If there is a malfunct ion in the retracta ble
rear spoiler* or the Audi magnetic ride*, it
may not be poss ible to activate sport
mode.
Acoustic parking system
Rear acoustic park assist
Applies to vehicles: wit h 4-channel acoustic park assist
Acous tic park assist gives a warning about
obstacles behind the vehicle.
Description
T he rea r acousti c park ass ist (4-cha nnel
a coustic park ass ist) determines the distance
of the vehicle from an obstacle using ultra­
son ic sensors. The sensors are in the rear
bumper. The volume a nd the pitch of the

80 Transmi ssion
Transmission
Manual transmission
Gearshift lever
Applies to vehicles: with manual transmission
The clutch pedal must be depressed all the
way before you can start the engine.
The manual transmission in your Audi is
equipped with an
interlock-feature.
• Depress the clutch pedal a ll the way.
• Start the engine with the gearshift lever in
Neutral and the clutch pedal depressed.
(D Note
Always depress the clutch peda l fully when
changing gears. Do not ho ld the vehicle on
a hill with the clutch pedal partially de­
pressed. This may cause premature clutch
wear or damage.
@ Tips
- Resting your hand on the gearsh ift lever
knob while driving will cause premature
wear in the transm ission.
- The back-up lights go on when you sh ift
i nto Reverse w ith the ignition on.
Gearshift pattern (6-speed manual
transmission)
Applies to vehicles: with 6-speed manual transmission
Fig. 79 Gearshift pattern: 6 -speed manual transm is­
sion
D rive in 6th gear for optim um fuel economy
when cruising . However, if more accelera tion
is required (when passing, for example), shift
down.
Eng aging rev erse gear (R )
• Move the shift lever all the way to the left,
press it down, then push it forward.
E spec ia lly after driv ing forward, stop the vehi­
cl e completely, shift into
Neutral and rest the
shift lever briefly in Neutral before shift ing in­
to
Reverse .
S tronic transmission
· Introduction
Applies to vehicles: with S tronic
Your vehicle is equipped with a S tron ic trans­
mission, also called a double-clutch system/
t ransmission .
Power is transferred between the engine and
the transmission by means of two independ­ ent clutches. They replace the torque convert­
er of conventiona l au tomatic transmissions
and allow the veh icle to accelerate wi thout a
noticeab le b reak i n the power flow.
With the aid of
tiptr onic , the gears can op­
t ional ly be shifted
manually~ page 84.
Selector lever positions
Applies to vehicles: with S tronic
All the selector lever positions are explained
in this section.
~-. -·~•-~ _ .. _....,-l
•+55 °F '
i} 340 mi
D
Fig . 80 Display: Selector lever pos it ion
T he instrument cluster display shows these­
lector lever position.
P -Park lock
In this pos ition the gears are mechanically
locked.

The park lock must only be engaged with the
vehicle
stationary c::> &.
To engage P and to remove the lever from th is
position, you must depress the release b utton
(button in the selector lever handle)
and si­
multaneously you must step on the brake
pedal.
R · re verse
I n th is position, reverse is engaged.
Reverse gear must only be engaged with the
veh icle
stationary and the eng ine runn ing at
id le speed
c::> ,&. .
To engage R, you have to depress the release
button
and s imultaneously step on the brake
pedal. In the R position, the back-up lights il­
lum inate with the ign ition on.
N • N eutra l
The transmission is in neutral in this position .
D -Norm al p osi tion f or d riving forwa rd
In this position, the forward gears are auto­ matica lly shifted up and down, depending on
engine load and vehicle speed.
To engage D from N, the brake peda l must be
depressed at speeds be low 5 km/h or when
the vehicle is stationary
c::> & .
In certain circumstances (driving in the moun­
tains for examp le) it can be beneficial to
switch temporarily to the manua l shift pro­
gram
c::> page 84 in order to adjust the gear
ratios to driving cond itions
manually.
S -Sport setting
The 5 se tt ing shou ld be selected for spor ty
d riving . The power reserves of the engine can
be fu lly exp loited through later upshifts.
To engage S from N, the brake pedal must be depressed at speeds be low 5 km/h or when
the vehicle is stationary
c::> & .
Tra n sm iss io n 81
A WARNING
- Never p lace the selector lever in the R or
P posit ion while the veh icle is moving -
risk of an accident!
- With the engine running, it is necessary
to hold the vehicle with the foot brake in all selector lever positions (except P and N), because even at idle speed the trans­
fe r of power is never completely inter­
rupted -the vehicle " creeps". If the vehi­
cle is stationary and the transmission is
engaged, the engine should never be
speeded up unintentionally (e .g. manual­
ly from under the hood). Otherwise the
veh icle w ill immediately start to move -
sometimes even if the park ing brake is
firmly applied - risk of an accident!
- Before you or other persons open the
hood and work on a running engine, the
selecto r lever must be moved to P and
the park ing brake applied f irmly - risk of
an accident! Follow the wa rning sticke rs
c::> page 174, Engine compartment.
(D Tips
If yo u have inadvertently shifted into N
while the vehicle is moving, you shou ld re­
move you r foot from the accelerator and
wait unt il the engine speed has dropped to
idle before shifting back to Dor 5 .
Selector lever lock
Applies to veh icl es: w ith S tronic
The selector lever lock prevents a gear from
being engaged accidentally and unintention­
ally setting the vehicle in mo tion.
F ig. 81 Selector lever locks

82 Transmi ssion
The selector lever lock is released as fo llows:
,. Switch the ignition on.
,. Step on the brake peda l
and simultaneously
hold down the re lease button .
Automatic selector lever lock
The selector lever is locked in the P and N po­
sitions when the ignition is on . To move the
l eve r from these positions the d river must de­
press the brake pedal. As a reminde r to the
d river, the fol low ing wa rning appears in the
instr ument cluster d isplay when the s electo r
is in P and N :
To start en g in e or sel ect gear ap ply fo ot
br ake when sta tionary
The selector lever lock is effective only when
the vehicle is stationary and at speeds be low
5 km/h. A t higher speeds, the lock in the N
position is automatically switched off.
The selector lever is not locked when rapid
shifts a re made th rough t he N pos it ion (e.g .
from R to D). This allows you to " rock" the ve­
hicle if it becomes stuc k. If the lever is in the
N position for more than 1 second with the
brake peda l not depressed, the se lector lock
engages automatica lly.
Rele ase button
The release b utton in t he se lector lever ha n­
d le prevents accidental shifts into certa in se ­
lecto r lever positions. When you press the re ­
lease button, the selector lever lock is cancel­
l ed. In the illustration, the pos it ions in which
the release but ton has to be pressed are high­
lighted in color
c> fig. 81.
Ignition key remo val lock
The ign it ion key can on ly be removed after the
ignition is switched off if the selector lever is
in P. As long as the ignit ion key is removed,
the selector lever is locked in P .
@ Tips
If the selector lever does not engage ,
there is a malfunction. The eng ine is disa­
bled to p revent the vehicle from driving off
unintent iona lly. To allow the selector lever to engage again, proceed as follows:
Press
and release the brake peda l.
Driving Notes
Applies to vehicles: w ith S tronic
The forward gears are shifted up or down au ­
tomatically.
-
------F ig . 82 Section fro m cente r co nso le : Se lecto r leve r
w it h re lea se but ton
Starting the engine
,. The se lecto r lever must be in the P or the N
po sit ion. At low temperatures (below -10
° C), the eng ine can only be started when the
selector lever is in the P position.
Starting from stop
,. Step on and hold the b rake pedal.
,. Hold the release button (bu tton in sele ctor
lever) down , move the selecto r lever to the
desired position, for example D
c> page 80,
and re lease the button .
,. Release the brake peda l and accelerate
Q _A .
Stopping t emporarily
,. Bring the veh icle to a full s top wi th the
brake, e.g . at traffic signals .
,. Do not acce lerate .
Parking
,. Step on and hold the b rake peda l¢ & .
,. App ly the parki ng b rake firmly .
,. Ho ld the release button down, move these­
lector lever to P and release the button .
Stopping on an incline
,. Always hold the vehicle with the footb rake
or park ing brake in orde r to prevent
IIIJJ,

Kick-down feature
Applies to vehicles: with S tron ic
The kick-down feature allows maximum ac­
celeration .
If you depress the accelerator pedal fully be­
yond the full-throttle position, the transmis­ sion automatically downshifts one gear, de ­
pending on vehicle speed and engine rpm . The
upsh ift into the next higher gear takes place
as soon as the max imum specified engine
speed is reached.
A WARNING
Please note that the drive wheels can spin
if the kick-down is used on a smooth s lip­
pery road - risk of skidding!
Launch Control Program
Applies to vehicles: with S tron ic
The Launch Control Program permits maxi ­
mum acceleration .
In o rder to u se La unch Control, the ASR (An ti­
Slip Reg ulation) mus t be d is a b led. When ASR
is disab led, the ESC wa rning/ind icator light
IJ
in the inst rument cluster illuminates . So that
L aunch Cont ro l can be used, the engine must
be at operating temperature and the steer ing
wheel must not be turned.
~ With the eng ine running , brief ly press the
ESC button . The message "Stabilization pro­
gram off" or "Sport control Warning! Re­
stricted stability" in the driver information
system d isplay.
~ Sh ift the gear lever to "S" or the tiptronic ®
pos it ion .
~ Step on the b ra ke peda l w ith your left foot
and keep the bra ke peda l fully depressed for
at leas t one second .
~ With your right foot, step on the acce lera ­
tor to the w ide-open throttle position o r
K ickdown . The engine speed settles at about
3,200 rpm.
~ Take your left foot off the brake .
Transm iss ion 85
A WARNING
-Always adapt your dr iving to the traffic
f low.
- Onl y use Launch Control when road and
traffic cond itions allow it and other dr iv­
ers will not be endangered or annoyed by
your driving and th e acce le rat ion of the
veh icle.
- Ma ke sure that ESC remains enab led.
With the ESC disab led, th e vehicle could
b ra ke away, part icularly on a s lick and
slippe ry ro ad - ris k of skid ding!
- Once acceleration is fi nished, switch AS R
on agai n by br iefly pushing t he ESC bu t­
ton.
Back-up program
Applies to vehicles: with S tronic
In the event of a system malfunction, there is
a back-up program.
In the event of system ma lfunction, the auto ­
matic transmission switches to the fai l-safe
mode. All of t he se lector lever position d is­
plays for the au tomatic tra nsmission a re hi gh­
li gh ted wi th a light b ackgro und in t he i nstr u­
ment cluster d isp lay . In some cases you can ­
not use reverse gea r any more.
If the t ransmission swi tches to fail-safe
mode, yo u should t ake the ve hicle to an au­
t horized Audi dea le rship as soon as possib le
to have the condition corrected.
Clutch is overheating
Applies to vehicles: with S tronic
• Clutch is overheating ! Please stop veh i­
cle!
If the symbols a re i lluminated, the clutch is
ove rheating a nd could be damaged if you con­
tin ue to drive. Stop the vehicle and a llow the
transmission to cool with the se lector lever in
the P posit ion while the engine runs at idle. If
the warn ing does not turn off, do not continue
dr iv ing . See your author ized A udi dealer or
i,..

86 Transmis sion
qualified repair facility for assistance. Other­
wise serious transmission damage could re­
sult . Once the indicator light has turned off,
drive to your authori zed Audi dealer or quali­
fied repair facility immediately to have the malfunction corrected .
Selector lever emergency release
Applies to vehicles: with S tro nic
If the vehicle's power supply fails, the selec­
tor lever can be released in an emergency.
-----Fig. 86 Se lector lever : Remov ing th e selector lever
boot
Fig. 87 Se lector lever: Using the eme rgency re lease to
move out of the Park pos ition
The emergency release mechanism is located
in the right front area under the selector lever
shift gate. Using the emergency release can
be comp licated. We recommend contacting
your authorized Audi dealer for assistance, if
necessary.
Removing the selector lever boot
.,. Activate the parking brake .
.,. Carefully pry the selector lever boot out of
the trim @using a small screwdriver .
.,. Pull both sides of the selector lever boot
upward in the direction of the arrow @ .
.,. Fold the selector lever boot upward.
Selector lever emergency release
.,. Press the release lever down and hold it in
p lace
¢ fig. 87.
.,. Press the release button in the selector lev­
er © and move the lever into the N position.
.,. Clip the selector lever boot back into the
shift gate after using the emergency re­
lease .
If the vehicle must be pushed or towed due to
a power failure (for example, the battery is
discharged), the selector lever must first be
moved to the N position using the emergency
release mechanism .
A WARNING
-Only move the selector lever out of the P
position when the park ing brake is activat­
ed. Otherwise, the veh icle could start to
move unintentionally when the selector
lever is moved out of the P position.