2013 AUDI TT wiper blades

come back a while later and drive off, the rain
sensor will reactivate itself after the vehicle
speed has exceeded 4 mph (6 km/h).
The rain sensor* is only activated with the
wiper lever set to position(!). When it starts
to rain, the rain sensor will automatically acti­
vate the intermittent wiping mode.
To reduce the sensitivity of the sensor, move
switch @ down. To increase the sensitivity,
move the switch up. The higher you adjust the
sensitivity, the faster the sensor will react
when it senses moisture on the windshield. The pauses between wiper turns depend not
only on the sensitivity setting, but on the ve­
hicle speed as well.
During brief stops, e.g . at a red light, wiper
motion will automatically be reduced to the
next lower speed . Wipers already turning at
low speed change to intermittent wiping.
When the ignition is turned on, the washer
jets are heated .
A WARNING
-Wiper blades are crucial for safe driving!
Only when they are in good condition are
they able to clear the windows properly
to provide uncompromising visibility.
Worn or damaged wiper blades are a
safety hazard
r=;, page 51, Replacing
windshield wiper blades!
- The light/rain sensor* is only designed to
assist and support the driver.
It remains
entirely the driver's responsibility to
monitor outside weather conditions and
to manually activate the wipers as soon
as rain or drizzle reduces visibility
through the windshield.
- The windshield must not be treated with
water-repellent materials. They can in­
crease glare under poor visibility condi­
tions such as wetness, darkness, or when
the sun is low on the horizon. In addi­
tion, they can cause the windshield wip­
ers to chatter.
Clear vision 49
@ Note
In freezing or near freezing conditions:
- Always check that the wiper blades are
not frozen to the glass before you turn
the wipers on. Loosen a wiper blade
which is frozen in place before operating
the wipers to prevent damage to the
wiper blade or the wiper motor.
- Do not use the wipers to clear a frosted
window. Using the wipers as a conven­ ient ice scraper will destroy the wiper
blades .
- Before you take your vehicle to an auto­
matic car wash, make sure you have the
windshield wiper system switched off (lever in position
0), otherwise the wind­
shield wiper system could get damaged
in the car wash if it should suddenly
come on.
@ Tips
-The windshield wipers are switched off
when the ignition is turned off. Activate
the windshield wipers after the ignition
is switched back on by moving the wind­
shield wiper lever to any position.
- Worn or dirty windshield wiper blades
cause smearing, which can affect the op­
eration of the light/rain sensor*. Check
the condition of your windshield wiper
blades regularly.
-The rain sensor is part of the interval
wiping system. Turning off the ignition
will also deactivate the rain sensor. To re­
activate the sensor, switch off the inter­
val wiping function, then switch it back
on again.
-Applies to vehicles with light/rain sen­
sor: When the wipers are switched on
manually and in rain conditions, the au­
tomatic headlights* turn on
r=;, page 42,
Switching the headlights on and off
or
off during the day when the wipers are
no longer operating. The automatic
headlights* function is available in this
case only when the light switch is in the
"AUTO" position¢
page 42, fig. 39.

50 Clear vis ion
- Make sure the washe r fl ui d reservoi r in
the engine compartment is topped
off
before going on a long t rip . L oo k up
c:> page 194 for checking and fi lling the
washer container.
- The w ipers only operate w ith the hood
completely closed.
Headlight washer system
App lies to vehicles : with hea dli ght washer syste m
The headlight washer system cleans the
headlights.
., Operate the windshield wiper/washer sys ­
tem
c:> page 48, fig. 50 ® with the head­
li ghts turned on by holding the lever for lon­
ger than one second.
The washe r jets extend forward o ut of the
front bumper driven by water pressure to
spray the front headlights with water.
You shou ld inspect the headlights regularly
(for example when refue ling) and clean
off
any solid dirt or insects from the lenses .
To ensure the system wo rks properly in winter,
keep the washer jets free o f snow and remove
any ice using a de- ic ing spray.
Service position
It is only possible to change wiper blades if
you move the wiper arms to the service posi ­
tion .
In o rder to use the windsh ie ld w ipers, the
front lid must be comp letely closed .
Moving wiper blades to the service
position
., When there is a ris k of frost, ma ke s ure that
the wiper b lades are not frozen to the wind ­
shield .
.. Switch the ignition on .
., Move the wiper lever to position
0
c:> page 48, fig. 50 .
., Press the I Re set I button until the D isplay
typ e
menu appears in the Driver Informa­
t ion System display . .,
Using the rocker switch and the
I R ese t! but­
ton, se lect the
Set > Wipe rs > Front > Serv ­
ice position on
funct ion . T he w indshield
w iper arms move to the service posit ion.
Mo ving wip er blades to pa rk position
., Ma ke certain that the w iper arms are ly ing
against the windshield .
., Switch the ignitio n on and move the wiper
lever from pos ition O
to 4 c:> page 48,
fig. 50. The w iper arms will move back to
the park position.
@ Note
Never drive your veh icle when the wind­
sh ield wiper arms are in the service posi­
tion and pulled away from the winds hield .
When you drive faster than
4 mph (6 km/
h), the wiper a rms automatically return to
the pa rk position and cou ld cause paint
damage to the front lid!
@ Tips
- Yo u can also tur n on the se rvice posit ion,
for example, if you want to p rotect the
w indshield from icing by us ing a cover.
- The service posit ion moves to
off auto­
matically whe n you ope rate the w ind­
shield wiper lever, o r speed exceeds
4 mph (6 km/h) .

Replacing windshield wiper blades
Wiper blades in good condition help keep the
windshield clear .
Fig. 51 Un l atc hing wiper blades
Fig. 52 Remov ing wiper blades
Removing the wip er blade
• Move the w ipers to the service position
<:;> page 50.
• Fo ld the w indshield wiper arm away from
the g lass.
• On the upper end of the wiper arm at the
corrugation, squeeze the plastic retainer to­
gether on both sides in the direction of the
arrow¢fig. 51.
• Rotate the wiper blade in the direction of
the arrow @¢
fig. 52 away from the wiper
arm .
• Lift the w iper blade off i n the direction of
the a rrow @.
Inst alling the wiper blade
• Place the rounded end of the wiper onto the
end of the wiper arm in the
opposit e direc­
t ion to the arrow@¢
fig. 52 .
• Swing the wipe r in the oppo site direction to
the a rrow @onto the wiper arm.
• Sq ueeze the corrugation on the w iper un til
you hear it click in the wipe r arm .
Clear vi sion 51
• Fold the wiper arm back onto the wind­
shield.
• Move the wipers to the park position
¢page SO.
The front wipe r blades measure left side
23.20 in. (590 mm) and right side 18.SO in.
(470 mm) in length.
C lean your wiper blades regularly with a wind ­
shield washer solution to prevent streaking. If
the blades are very dirty, for example with in­
sects, carefully clean the blades with a sponge
or a soft brush.
If the wiper blades begin to streak the wind­
shield, this could be caused by residue left on
the windshie ld by automatic car washes.
Fill the wi ndshield washe r container with a
spec ial solutio n availab le at your a uth orized
Audi dealer to remove the resid ue .
Be sure to inspect t he condition of your wiper
blades regularly. For safety reasons, rep lace
your wiper blades once or twice a year if nec­
essary . See yo ur authorized Aud i dealer for re­
placement blades.
A WARNING
- Clean your wiper blades regu larly with a
windshie ld washer so lution to prevent
streaking. If the w iper blades are very
d irty, fo r example with insects, ca refully
clean the wiper blades with a sponge or a
s oft br ush.
- For your safety, yo u should rep lace the
w iper b lades once o r twice a yea r. See
your author ized Audi dealer for repla ce­
ment b lades .
(D Note
-The windshie ld w iper blades m ust only
be replaced when in the service pos ition
q page 50! Otherw ise, you risk damag­
ing the paint on the hood or the w ind­
shield w ipe r moto r.

52 Clear vis ion
- To help prevent damage to the wiper sys ­
tem, a lways loosen blades which are fro ­
zen to the windsh ield before operat ing
wipers.
- To he lp prevent damage to w iper blades,
do not use gasoline, kerosene, pa int
thinner, or other solvents on or near the
wiper blades.
- To he lp prevent damage to the wiper
arms or other components, do not at­
tempt to move the wipers by hand .
(D Tips
-Commercial hot waxes applied by auto­
matic car washes affect the cleanability
of the glass surface .
- The front wiper blades are different
l engths; the blade on the driver's s ide is
l onger .
Digital compass
Activating or deactivating the compass
Applies to vehicles: with digital compass
The direction is displayed on the interior rear
view mirror.
Fig . 53 In side rea r vi ew m irro r: digi tal compass ac ti­
v at ed
.. To activate o r deactivate, hold the@
c::> fig. 53 b utton down until the red disp lay
appe ars or d is a ppears.
The digital compass only works with the igni­
tion tu rned on . T he d irect io ns are displayed as
ini tia ls :
N (North), NE (No rthe ast) , E (E as t),
SE (Southe ast), S (Sou th), SW (Southwest),
W (West) , NW (Northwest).
(D Tips
To avoid inaccurate directions, do not al­
l ow any remote contro ls, electr ica l sys­
tems, or metal parts close to the mirror .
Setting the magnetic deflection zone
Applies to vehicles: with digita l compass
The correct magn etic deflection zon e must be
set in order to display the dire ctions correctly.
©
Fi g. 54 North A meric a: magne tic def le ction zo ne
bo un daries
" Ho ld th e@ c::> page 52, fig . 53 button down
until the number of the set magnetic deflec­
t ion zo ne appe ars on the inte rior re ar v iew
m irror.
.. Adjust the magnetic de flect ion zone by re­
peated ly pressing on the @button . The set
mode automatically deact ivates after a few
seconds.
Calibrating the compass
Applies to vehicles: with digita l compass
The compass has to b e recalibrated if the dis ­
play is wrong or inaccurate.
.. Hold the @button down unti l th e letter C
is displayed on the inter ior rear view mirror . ..,.

~ Wipe the windows dry with a clean piece of
cloth or kitchen paper towel.
The best way to remove snow from windows
and mirrors is to use a brush. Use a non-abra­
sive
plastic ice scraper -better still, a spray
deicer -to remove
ice from windows and mir­
rors.
The windows must not be cleaned with insect
remover or wax since these can interfere with
the function of the windshield wiper blades
(chatter).
Oil, grease or silicone residue can be removed
with
glass cleaner or silicone remover. How­
ever, wax residue requires the use of a special­
ly formulated solvent. Please contact your
Audi dealer for advice on safe products for
wax removal.
Windows should also be cleaned on the inside
at regular intervals.
Never dry windows with the same chamois
that you use to dry painted surfaces. Wax resi­
due on the chamois can impair vision through
the windows.
A WARNING
-The windshield must not be treated with
water-repellent materials. They can in­
crease glare under poor visibility condi­
tions such as wetness, darkness, or when
the sun is low on the horizon. In addi­
tion, they can cause the windshield wip­
ers to chatter.
- Always read and heed all WARNINGS and
other information
¢page 164.
(D Note
-Never use warm or hot water to remove
snow and ice from windows and mirrors.
This could cause the glass to crack.
- To prevent damage to the wires of the
rear defogger, do not place any adhesive
stickers on the inside of the rear window
over the wires.
- To help prevent dirt from scratching the
window, always scrape in a forward di-
Cleaning and protection 169
rection -pushing the scraper away from
you -never back and forth.
· Steel wheels
Applies to vehicles : with steel wheels
The wheels also have to be cleaned.
~ Always include the hub caps and wheel rims
when washing your vehicle to remove road
dirt, salt sprays and brake dust.
If necessary, use a commercial wheel cleaner
to remove accumulated brake dust.
The wheel rims are easier to keep clean if they
are regu larly coated with liquid wax.
Paint scratches should be touched up as soon
as possible to prevent corrosion
¢ page 168,
Touch-up paint.
A WARNING
-Moisture and ice on brakes may affect
braking efficiency -
¢ page 153, General
information.
Test the brakes carefully af­
ter each vehicle wash.
- Always read and heed all WARNINGS and
the information
¢page 164.
Cast (light) alloy wheels
Applies to vehicles: with Cast alloy wheels
Cast (light) alloy wheels require special care.
~ Wash the wheels with a sponge or hose
brush every other week.
~ For deep cleaning afterwards, use only a
dedicated
acid-free cast alloy wheel cleaner .
~ Rub a coat of liquid wax onto the rims every
three month. Be sure to reach and treat all
parts of the rim.
To preserve the decorative appearance of the
cast alloy wheels, some special care is neces­ sary. In addition to road dirt and salt, brake
dust is also corrosiv e. If left on for too long,
brake dust can cause pitting.
Use only special
acid-free cleaners formulated
for alloy rims. Safe products are available at
your Audi dealer. Never leave the cleaner on .,..
•
•

258 Index
Glossary of tire and loading termino lo-
gy .. .. .... ............. .. .. .... .
197
New tires and wheels ...... .. .. .... . 207
Tires and vehicle load lim its .. .. ..... 204
Wheels/T ires
Steel whee ls ........... .. .. .. .... .
169
When must the airbag system be inspect-
ed? ... .. .. ............... .... .. .. .
119
When should I ad just the tire pressures? 203
When shou ld I check the tire pressures? . 203
Where are lower anchorages located? .. . 144
Where can I find the tire pressures for my
car? .. .. .. .. ..... ........ .. .. .... .
202
Why safety belts? . . . . . . . . . . . . . . 100, 101
W indows
C leaning .................. ...... . 168
Conven ience close/open feature . .. .. ..
40
D efrost .. .. ... .......... ...... .. .. 69
Windshield washer fluid .............. 20
Windshield wipers
Folding up ............ .. .. .. .... .. 51
Replacing windshie ld wiper blades ..... 51
Service position . . . . . . . . . . . . . . . . . . . . SO
Washer fluid reservoir .............. 194
Winter operation Battery ..... .. .......... .. .. .... .
190
Coolant system . . . . . . . . . . . . . . . . . . . 187
Defrosting windows . . . . . . . . . . . . . . . . .
69
He ated seats (climate control) . . . . . . . . 70
Tires .. .. ................. ...... . 155
W indows .. ... .. ..... ......... .. . 168
Winter tires ........................
211
All-wheel drive .................... 211
Wiper and washer system ....... .... .. 48
In termi ttent wiping ........ .... ... .. 48
One-tap wiping ......... .... .. .... .. 48
X
X enon-Lights .... .......... .. .. .... . 231