2013 AUDI TT change wheel

Tightening
• Fit the wh eel b olt wren ch over t he wheel
bolt and push it down as far as it will go .
• Close your gr ip aro und the
end of the
wrench handle for maximum torque and
turn each whee l bolt
cl ock wise until it sits
tight.
A WARNING
- Us ing force without control to speed the
wheel change up can cause the veh icle to
slip off the jack and cause serious pe r­
sonal inj uries.
- Do not loosen the wheel bolts more than
one turn
before you ra ise the veh icle with
the jack. -Risk of inj ury!
@ Tips
- Never t ry and use the hexagonal socket
i n the handle of the screwdriver to loos­
en o r tighten the wheel bolts .
- If a wheel bolt sits very t ight, you may
find it easie r to loosen by carefully push­
i ng down on the end of the whee l bolt
wre nch w ith
one foot only. As you do,
ho ld on to the ca r to keep yourse lf stable
and ta ke care not to slip .
Raising the vehicle
The vehicle must be li~ed with the jack first
before the wheel can be removed .
Fig. 160 Sill pa nels : m arkin gs
What do I d o now ? 225
Fig. 1 61 Sill : pos itio ning the veh icle jac k
• Apply the parkin g brake firmly to prevent
your veh icle from rolling unintentionally.
• Shift into
1st gear on vehicles with manual
transm iss ion, or move the
se lecto r l ever to
the P p ositio n
on vehicles with automatic
transm ission .
• Pos it ion the jack be low the door sill under
the
mounting point that is closest to the
wheel to be changed
r=> fig. 160.
.. Extend the jack under the lifting point on
the door sill until its arm is posit ioned di ­
rectly under the l ifting point ¢&_ .
• Align the jack so that its arm@¢
fig. 161
engages in the designated lifting point in
the door s ill and the movable base ® lies
flat on the ground. The base @ must be
ver­
tical
under the lifting point @.
• Wind the jack up further until the flat t ire
comes off the ground
r=> &_ .
Position the vehicle jack
onl y under the desig­
nated lifting points on the si ll
r=> fig. 160.
There is exactly one locat io n for each wheel.
The jack must not be positioned at any other
location
r=> ,&. r=>(D .
An un stab le su rfa ce under the jack can cause
the veh icle to slip off the jack . Always provide
a firm base for the jack on the ground . If nec­
essary place a sturdy board or similar support
under the jack . On
hard , slipper y surf aces
(such as tiles) use a rubbe r mat or similar to
prevent the jack from slipping
c:::> .&. .
A WARNING
-You or your passengers co uld be in ju red
while changing a wheel if you do no t fo l­
low safety precautions :

226 What do I do now ?
-Position the vehicle jack only at the
designated lifting points and align the
jack. Otherwise, the vehicle jack could slip and cause an injury if it does not
have sufficient ho ld on the vehicle.
- A soft or unstab le surface under the
jack may cause the vehicle to slip off the jack. Always prov ide a firm base for
the jack on the ground.
If necessary,
use a sturdy board un der the ja ck .
- On hard, slippery surfac e (such as tiles)
use a rubber mat o r similar to prevent
the j ack fr om s lipp ing.
- T o he lp p revent injury to yoursel f and
yo ur passenge rs:
- Do not raise the vehicle unti l yo u are
sure the jack is sec urely engaged.
- Passenge rs must not rema in in the ve­
h icle when it is jac ked up .
- Make sure that passen gers wait in a
safe p lace away from the vehicle and
well away from the roadway and traffic.
- Make sure jack position is correct, ad­
just as necessary and then contin ue to
ra ise the jack.
0 Note
A floor jack or the pads on the hoist arms
m ust
not be positioned at the points
shown
-arrows-.
Taking the wheel off
Follow these instructions step -by -step for
changing the wheel.
Fi g. 1 62 W heel change : us ing the screwd river ha ndle
(w ith the b lade removed) to turn the bolts
Fig. 163 Whee l cha nge : alig nme nt pin in side the top
hole
After you have loosened all wheel bo lts and
raised the vehicle off the ground, pe rform t he
fo llowing steps to remove and replace the
wheel:
Removing the wheel
.,. Use the
hexagonal s ocket in the screwdri v·
er handle
to completely tur n out the top ­
most whee l bolt and set it aside on a
clean
surface c;, fig. 162.
.,. Screw the threaded end of the alignment
pin from t he too l kit hand-t ight into t he
now vacant bolt hole
c:> fig. 163 .
.,. Then completely unscrew the other wheel
bolts as desc ribed above.
.,. Take off the whee l leav ing the a lignment
p in in the bo lt ho le
c;, (D .
Putting on the wheel
.,. Lift the spa re wheel and carefully s lide it
over the alignmen t pin to g uide it in place
c;, (D .
.,. Use the he xagonal socke t in the screwdr iver
h and le to screw in and tig hten all whee l
bolts
slightly .
.,. Unscrew the alignment pin and insert and
tighten the remaining whee l bolt slightly
like the rest .
.,. Turn the jack handle co unte r-clockwise to
lower the vehicle until the jack is fully re­
leased .
.,. Use the wheel bo lt wrench to tighten all
wheel bo lts firm ly
c;, page 224 . Tighten
t hem
cro sswise, from o ne bol t to the ( ap­
proxima tely) opposi te one, to keep the
wheel cente red.

(D Note
When removing or installing the wheel,
the rim could hit the bra ke rotor and dam­
age the rotor . Wor k carefully and have a
second person help you.
N ever use the hexa gonal s ocket in the ha n­
d le of the screwdriver to loosen or t ighten
the wheel bolts.
- Pull the reversib le blade from the screw­
drive r before yo u use the hexagonal
socket in t he handle to t urn the whee l
bo lts .
- When mounting tires with
unid irectional
tread design
make s ure the tread pat­
te rn is poi nte d the r ight way
¢pag e 227.
-The wheel bolts should be clea n and easy
to tu rn . Ch eck for dirt and corros ion on
the mat ing su rfaces of both the whee l
a nd th e hu b. Remove a ll dir t fro m these
s ur fa ces before remo unting the wheel.
Notes on wheel change
Pl ease rea d the information ¢ page 207, New
tires and replacing tires and wheels,
i f you are
going to use a spare t ire which is different
from the tires on your ve hicle.
Afte r you change a tire:
- Check the tire pressure on the spare imme ­
diately after mounting .
- Have the wheel bolt tightening torque
che cked with a torque wrench as soon as
possible by your authorized Audi dealer or
a qualified service station.
- With steel and alloy wheel rims, the wheel
bolts are correctly tightened at a torque of
90 ft lb (120 Nm) .
- If you notice while changing a tire that the
wheel bolt s are co rroded and diffi cult to
turn , then they should be replaced before
you check the t ightening torque.
What do I do now? 227
- Replace the flat tire with a new one and
have it installed on your vehicle as soon as
possible. Remount the wheel cover .
Until then , drive with extra care and at re­
duced speeds.
A WARNING
-
- If you are go ing to e quip your ve hicl e
wit h tires o r rims which differ from those
which were factory installed, t hen be
sure to read the information¢
page 207,
New tires and replacing tires and
wheels .
-Always sto re the tools secu rely in lug­
gage compartment. Othe rwise, in a n ac­
cident o r su dd en maneuv er they cou ld fly
forwa rd, causi ng injury to passe ngers in
the vehicle.
Tires with unidirectional tread design
Tires with unidirectional tr ead design must be
mounted with their tread pattern pointed the
right dire ction.
A u nidirectional tire can be identified by ar­
rows on the sidewall,
which point in the direc ­
tion of t he rota tion. Yo u m ust follow the
s p ecifie d direction of rot ation. This i s nece ssa ­
r y in order fo r these tires to develop t heir op­
timum character istics regard ing grip, road
no ise, wear, and hydrop la ning.
•
•