2013 AUDI TT change wheel

Tires and wheels 201
you have stored. The system does not recog ­
nize the load condition of your vehicle.
The effectiveness of the tire pressu re monitor­
ing system w ill be impaired if you store nor­
mal load pressures but then operate the vehi ­
cle at its maximum load¢,& .
See the illustration ¢
fig. 142 for the location
of the label on driver's side B-pillar (color of
the actual labe l and exact location on the ve­
hicle will vary slig htly) .
Note that the following table is accurate at
the time of go ing to press and is subject to change.
In the event of discrepancies, the tire
pressure label (on driver's side B-pi llar) always
takes precedence.
T he table below lists the recommended cold
ti re inflation pressures for the Audi mode l
covered by your Owner's Literature at the vehi­
cle's capacity weight and the tir e sizes instal­
l ed on the respective models as orig inal
equipment, or as a factory option.
I
Model/ U Tire designation Tire pressure front Tire pressure rear
Engine normal load normal load
condition full load condition full load
(upto 2 oc- condition (up to 2 oc-
condition
cupants) cupants)
PSI JI kPA PSI ]I kPA PSI II kPA PSI II kPA '.
TT/TIS: 225/50 Rl 7 94H All Sea-
32 220 32 220 29 200 29 200
2.0 liter son
4-cylin-
225/50 Rl 7 94W XL High
der Performance
32 220 32 220 29 200 29 200
245/45 R17 95H All Sea- 32 220 32 220 29 200 29 200
son
245/45 R17 95VXL High
32 220 32 220 29 200 29 200
Performance
245/40 R18
93H All Sea-
32 220 32 220 29 200 29 200 son
245/40 R18 93V XL High
32 220 33 230 29 200 30 210
Performance J
255/35 R19 96V XL High
32 220 32 220 29 200 29 200
Performance
TT RS:
245/40 R18 93V 220
2.5 liter
255/35 R19 96V XL High
5-cylin- Performance
35 240 36 250 32 220 32 220
der
XL= reinforced or extra load tire. It may also appear as xl, EXTRA LOAD, or RF on the tire side-
wall.
The correct tire pressure for the spore wheel i s
located on a label on the driver's side B-pillar.
Because technical changes may be made to
ve hicle equipment during the model year, a l­
ways compare the tire size designation on the tire press
ure label on your vehicle with the
tires on your vehicle. Make sure that the tire
s ize info rmat ion on the vehicle label is the
same as the size of the tires on the veh icle .
This is especially important if the vehicle be-
long s to someone e lse o r you boug ht the ..,.
•
•

204 Tire s and wheel s
-If the tire pressure is too low or too high,
the tires w ill wear prematurely and the
vehicle will not handle well.
- If the tire is not flat and you do not have
to change a wheel immed iately, drive at
reduced speed to the nearest service sta­
t ion to check the tire pressure and add
air as required.
(D Note
Dr iving without valve stem caps can cause
damage to the t ire va lves. To prevent this,
always make sure that facto ry installed
valve stem caps on all wheels a re securely
mounted on the valve.
@ For the sake of the environment
Underinf lated tires will a lso increase the
fue l cons umption .
Tires and vehicle load limits
There are limits to the amount of load or
weight that any veh icle and any t ire can c arry.
A vehicle that is overloaded w ill not h andle
well and is more difficult to stop. Over load ing
can not on ly lead to loss of vehicle contro l,
but can a lso damage important parts of the
vehicle and can lead to sudden tire failure, in­
cluding a blowout and sudden deflation that
can cause the veh icle to crash .
Your safety and that of your passengers a lso
depends on making sure that load limits are
not exceeded. Vehicle load includes everybody
and eve ryth ing in and on the vehicle . These
l oad limits a re tech nica lly refe rred to as the
ve hicl e's
Gros s Vehicl e W eight Rat ing
("GVWR").
The "GVWR" includes the we ight of the basic
vehicle, all factory installed accesso ries , a fu ll
tank of f uel , oi l, coo lant and othe r fluids plus
maximum load. The maxim um load includes
the number o f passengers that the vehi cle is
intended to carry ("seating capacity") with an
assumed weig ht of 150 lbs (68 kg) for each
passenger at a designated seating position and the total weight of any luggage
in the ve ­
hicle .
T he
Gro ss Axle Weight Rating (" GAWR") is
the max imum load th at can be applied at e ach
of the vehicle's two axles .
T he Gross Vehicle Weight Rat ing and the
G ross Ax le Weight Ra ting are listed on the
sa fety comp liance s ticke r label lo cated on the
driver's side B-pillar. Your Audi has 4 seat ing
positions, 2 in the front and 2 in the rear fo r
total seat ing capac ity of 4. Each seating posi­
t ion has a safety be lt c>
page 100 , Safety
bel ts.
The fact that there is an upper limit to yo ur
vehicle's Gross Vehicle Weight Rating means
that the total weight of whatever is being car­
ried in the vehicle is lim ited. The more passen­
gers in the vehicle or passengers who are
heavier than the standard we ights assumed
mean that less we ight can be carried as lug­
gage.
The tire pressure label on your Aud i also lists
the max imum combi ned weig ht of all of the
occupants and luggage or other cargo t hat
t h e vehi cle can carry . Fo r th e lo cat ion of the
la bel c>page200,
fig.1 42.
_& WARNING ~
Overloading a vehicle can c ause loss o f ve-
h icle cont ro l, a c rash or other accident, se ­
rious pe rsonal injury, and even death.
- Ca rrying more we igh t tha n your veh icle
was des igned to carry wi ll prevent the
veh icle from handling proper ly and in­
crease the risk of the loss of ve hicle con­
trol.
- The brakes on a vehicle that has been
overloaded may not be able to stop the
veh icle w ith in a safe distance .
- Tires on a vehicle that has been over load­
ed can fail s uddenly , incl uding a blowout
a nd sudden deflation, causing loss of
control and a crash .

remain continuous ly illuminated . This se ­
quence will continue upon subsequent vehicle
start-ups as long as the ma lfunction ex ists.
When the malfunct ion indicator is ill uminat­
ed, the system may not be able to detect or
signa l low tire pressure as intended. TPMS
malfunct ions may occur for a variety of rea­
sons, including the installat ion of replace­
ment or alternate tires or wheels on the veh i­
cle that prevent the TPMS from funct io ni ng
properly. Always check the TPMS malfunct ion
tellta le afte r replacing one or more t ires or
wheels on your veh icle to ensure that the re­
p lacement or a lternate tires and wheels allow
the TPMS to continue to function properly.
Tire pressure indicator appears
Applies to vehicles: with tire pressure monitoring system
The tire pressure indicator in the instrument
cluster informs you if the tire pressure is too
low or if there is a system malfunction.
F ig. 1 47 Disp lay : under infla tion warn ing
Using the ABS sensors, the tire pressure moni ­
toring system compares the t ire tread circum­
fe rence and vibration characteristics of the in­
d iv idual tires . If the pressure decreases in one
or mo re tires, th is is indicated in the instru­
ment clus ter with a warning symbol
RE and a
message
'* fig. 147. The dr iver message in the
d isp lay goes out after 5 seconds. The driver
message can be d isplayed again by pressing
the
! CHECK I button @¢ page 10, fig . 3 . If on ­
ly one tire is affected, the display will indicate
its pos ition.
The ti re pressure monito ring m ust be reset in
the menu display each time the pressures are
ad justed (e.g. when switching between parti-
Tire s an d wheel s 215
al and fu ll load pressure) or after changing o r
replacing a tire on your vehicle '*
page 216.
The TPMS indicator on ly mon itors the t ire
pressure that you have previously stored . You
can f ind the recommended tire pressures for
your vehicle on the label on the driver's door
pillar ¢
page 200.
Tire tread circumference and vibration charac­
teristics can change and cause a tire pressure
warning if:
- the t ire press ure in one or more tires is too
low,
- the tire has structural damage,
- the t ire press ure was changed, wheels rotat -
ed or rep laced but the TPMS was not reset
¢ page 216.
Warning symbo ls
RE L oss of pressure in a t least one tire ¢ ,&..
Check the tire or tires and rep lace or repa ir if
necessary . The indicator light
RE in the inst ru­
ment cluster a lso i lluminates
¢ page 13 .
Check/correct the press ures of all four tires
and reset TPMS in the menu display .
Iii;~, (T ire Pressure Monitoring System) Ti re
pre ssure! System malfun ction .
Ifllilff' ap­
pears after switching the ignition on or whi le
driv ing and the indicator light
RE in the in­
strument cluster blinks for approx imately one
minute and then stays on, there is a system
malfunction .
Attempt to store the correct tire pressure '*
page 216. If the indicator light does not
turn off or if it turns on shortly thereafter, im ­
med iate ly dr ive your vehicle to a n author ized
Audi dealer or author ized repair fac ility to
have the malfunct io n cor rected.
.8, WARNING
-
- If the tire pressure ind ic a tor ap pears in
the ins trumen t cluster display, one or
more of your tires is significant ly under­
inflated . Reduce yo ur speed immediately
and avoid any hard steer ing or braking
maneuvers. Stop as soon as possible and
check the tires and their pressures.
~
•
•

216 Tires and wheels
Inflate the tire pressure to the proper
pressure as indicated on the vehicle's tire
pressure label¢
page 200. Driving on a
significantly under-inflated tire causes
the tire to overheat and can lead to tire
failure. Under-inflation also is likely to
impair the vehicle's handling and stop­
ping ability .
- The driver is responsible for maintaining
the correct tire pressures. You must
check the tire pressures regularly.
- Under certain conditions (such as a spor­
ty driving style, winter conditions or un­
paved roads), the pressure monitor ind i­
cator may be delayed.
- Ask your authorized Audi dealer if run­
flat tires may be used on your vehicle .
Your vehicle registration becomes invalid
if you use these tires when not permit­
ted. Damage to your veh icle or accidents
could also result.
- If you switch between standard and run­
flat tires, an authorized Audi dealer or
qualified workshop must reprogram the
control module .
@ Tips
-The tire pressure monitoring system
stops working when there is an ESC/ABS
malfunction.
- Using snow chains may result in a system
malfunction .
- The tire pressure monitoring system on
your Audi was developed using t ires with
the "AO" or "RO" identification on the
tire sidewall ¢
page 207. We recom­
mend using these tir es.
Reset tire pressure monitoring system
(Stepl)
Applies to veh icles: w ith tire pressure monitoring system
If the tire pressure is adjusted, wheels are ro­
tated or changed, the TPMS must be reset in
the menu display.
----- ®
Fig. 148 Wipe r lever: Contro ls fo r the menu d isplay
Fig. 149 Disp lay: S ta rt m enu
I Rese t I button @ and rocker switch @
¢
fig. 148 functions:
To open the menu
" Press the I Reset ! button @ unt il the menu
disp lay
~fig. 149 appears
Selections and settings
" Press the rocker switch @ to reach a menu
disp lay. The switch is operated the same as
the display (up/down) .
Entering and confirming
" Press the I Reset I button @.
Returning to the Start menu
" Press the I Rese t I button longer than 2 sec­
onds to return from any menu level to the
Start menu.

@ Tips
-Before resetting the TPMS, the current
pressures of
all four tires must corre­
spond t o the specified va lues. Adjust the
tire pressu re and reset the pressure in
the tire pressure mon itor ing system ac­
cord ing to the load yo u are carry ing
c::> page200.
- Do not store the tire pressure if there are
snow cha ins on the tire .
Reset tire pressure monitoring system
(Step2)
A pplies to vehicles: with t ire pressure monitoring syste m
Fig. 150 D isplay: Tire pressure
Fig. 151 D isp lay: Tir e pressure
I Reset ! button @ and rocker sw itch @
c::> page 216, fig. 148 functions:
Storing tire pressure s
.,. Turn on the ignition.
.,. Se lect the menu :
> Adjusting* > Tire pres-
sure
> Store .
Entering and confirming
.,. Se lect the menu: Store now
.,. Press the
!Reset I button @.
.,. Se lect the menu: Confim
.,. Press the
!Reset I button @. Tires and wheels 21
7
Returning to the Start menu
.,. Press t he I Reset l butto n longer tha n 2 sec­
onds to re turn from any menu level to the
Start men u.
(D Tips
-Before rese tt ing the TPMS, the c urrent
pressures o f
all four tires must corre­
spond to t he spec ified values . Adj ust t he
t ir e pr essure and reset the pressure in
the tire pressu re monitoring system ac­
co rding to the load you are ca rrying
c::> page 200.
- Do not store the tire pressure if there are
snow chains on the tire.
Run-flat tires
Introduction
Applies to vehicles: wit h Run-fla t tires
Run-flat tires help keep you moving if a tire
goes flat.
Re inforced sidewalls give the t ires r un-flat ca­
pabili ty if tire pressure is lost .
We recommend that run-flat tires o nly be
mounted on vehicles that were orig inally
equipped with these special t ires at the facto­
ry an d have a Tire Pressu re Monitoring Sys­
tem .
Run-flat tir es can be identifi ed by th e letters
"RSC" on the tire sidewall.
If you do change the tires on your veh icle from
no rma l to run-flat tires, you must buy the
special rims required fo r run-flat tires, and the
T ire Pressu re M on itor ing System must be re­
programmed by an authorized Aud i d ealer o r
othe r qualified wo rkshop .
What do run -flat tires do?
These special tir es have run-flat capab ilities
that help keep you moving if a tire loses pres­
s ur e and goes flat. Under favorab le condi tions
t ir es can be dr iven
at least 30 miles (SO km) ,
but you mus t not drive fa ster than SO mph
( 80 km/h)
c::> page 218, Driving with run-fla t
tires .
Ill-

218 Tires and wheels
When it is not possible to continue
driving , even with run-flat tires?
-If the E lectronic Stabilization Control (ESC)
is not working or keeps coming on.
- If the
Tire Pr essure Monitoring System does
not work .
- If the tire has been severely damaged, in a
crash , for example. The tread can separate
from a damaged tire as the wheel turns, and
hit parts of the vehicle, such as the fuel tank
filler neck , fuel lines or brake lines.
- Do not continue driving if severe vibration occurs or if the tire starts to smoke because
the tire is running hot.
- Do not continue driving if damage to the
tire, such as cracks in the sidewall, appears.
A WARNING
Improper use of run-flat tires can cause
vehicle damage that can lead to loss of ve­
hicle control, a crash and serious personal
lnJUry.
- Run-flat tires can only be used with spe­
cial rims.
- Run-flat tires must always be mon itored
with a properly programmed Tire Pre­
ssu re Monit oring Sys tem.
- Always inspect a tire that has lost air to
make sure it is safe to drive with the tir e
in the run-flat mode.
- Never drive with run-flat tires that have
been damaged in a collision.
- Never drive with run-flat tires if heat
build-up causes the tire to give off
smoke.
- Never drive with run-flat tires if the vehi­
cle shakes or vibrates severely.
- Never drive with a run-flat tire that de­
velops sidewall cracks or other damage
wh ile in use .
-If you switch between standard and run­
flat tires, an authorized Audi dealer or
qualified workshop must reprogram the
control module.
(D Note
Run-flat tires have specia l characteristics
and requirements, that are very different
from conventional tires. Run-flat tires re­
quire special rims for run-flat use and can­
not be used on conventional wheel rims.
(D Tips
- If you are not able to cont inue driv ing
w ith run-flat tires, please seek professio­
nal assistance.
- Please contact your authorized Audi
dealer or Audi of America, Inc. if you
have questions about tires and rims .
Driving with run-flat tires
Applies to vehicles: wit h Run -flat tires
Handling characteristics change when tire
pressure is low .
Driving on tires with low tire pressure changes
the way a veh icle handles, particularly when
cornering and braking. The handling charac­
teristics of run-flat tires do not seem to
change a lot even when driving on low pres­
sure or in the run-flat mode . Nevertheless you
must still take spec ia l precautions when oper­
at ing a vehicle on run-flat tires when tire pres­
sure is low o r the tire(s) is flat:
.,. Th e Electronic Stabilization Control (ESC)
must be switched on.
.,. Never drive faster than SO mph (80 km/h)
q &_ .
.,. Plan ahead when driving and anticipate
what you will have to do considering traffic
and road conditions up ahead .
.,. Accelerate carefully.
.,. Avo id unnecessary and sudden steering and
brak ing maneuvers .
.,. Reduce your speed in plenty of time before
intersections, curves and other places where
you may have to react qu ickly.
Please see:
qpage 218, When it is not possi­
ble to continue driving, even with run-flat
tires?

Handling characteristics change when
driving with low air pressure or with flat
tires even with special run-flat tires
A low pressure or flat front tire affects vehicle
handling characteristics by pu lling the vehicle
slightly to the side where the tire is mounted
and reduces braking performance .
A low pressure or flat
rear tire also affects
driving character istics by pulling to the side
where the tire is mounted and also reduces
brak ing performance. The effect on vehicle
handling is most not iceable when driving
around curves.
A WARNING
Changed vehicle handling character istics
when driving in the run -f lat mode can
cause loss of vehicle contro l, a crash and
serious personal injury.
- Driving on special run-flat tires in the
run-f lat mode wi ll change vehicle han­
dling characteristics during braking,
when cornering and under heavy acceler­
ation.
- Never drive faster than the maximum
rated speed of 50 mph (80 km/h) when
dr iv ing in the run -flat mode.
- Always adjust vehicle speed to traffic,
road and weather cond itions and drive
slower than the max imum rated speed if
necessary weather and road conditions
are taken into account.
- Always obey speed limits and other traf­
fic laws.
Q) Note
We always recommend driving w ith even
more care when using these special t ires in
the run-flat mode . Always avo id sudden
maneuvers.
Tires and wheels 219
Replacing run-flat tires and rims
App lies to veh icles : w it h Run -flat t ires
Your vehicle was especially designed to use
special run-flat tires.
You may use and combine only approved run­
flat tires and special matching rims that have
been designed for run-flat tires . Mounting
special run-flat tires on standard wheels will not work and w ill not prov ide the advantages
fo the ru n-falt feature . Never use spec ial run­
flat tires on standa rd wheel rims.
After dr iving with a tire i n the run-flat mode,
always have the vehicle and affected tire(s)
and rim(s) inspected by a n authorized Audi
dealer. Tires that have been driven in the run­
f lat mode must be rep laced .
A WARNING
-Use of damaged run-flat tires and rims can
cause vehicle damage that can lead to loss
of vehicle control, a crash and serious per­
sonal injury.
- Always have the vehicle and affected
tire(s) and r im(s) inspected by an author­
ized Audi dealer after driving a tire in the
run-flat mode .
- Tires that have been dr iven in the run­
flat mode must be replaced.
•
•

224 What do I do now?
What should I be
aware of when
changing a tire?
General information
The following sections will provide you with
important information on how to change a
tire using the vehicle tool kit.
However, we recommend that you have a
qualified service center change the tire and
perform all work associated with changing it .
Wheels with cap-covered wheel bolts
Applies to vehicles: with cap-covered whee l bolts
The caps must be removed first from the
wheel bolts before the bolts can be un­
screwed .
Fig. 157 Wheel change: removing the wheel bolt caps
Removing
• Push the plastic clip provided with the on­
board tool kit down over the wheel bolt cap
u ntil it engages.
• Pull on the properly engaged
plastic clip to
extract the cap¢
fig. 157 .
Refitting
• Place the caps over the wheel bolts and
push them back in.
The caps are there to protect and keep the
wheel bolts clean.
Decorative wheel covers
Applies to vehicles: with decorative wheel covers
The decorative wheel covers must be removed
first to access the wheel bolts .
Fig. 158 Wheel change: removing the wheel cover
Removing
• Insert the hook prov ided with the on board
tool kit into the hole on the center hub
piece.
• Pull off the
decorative wheel cover
¢fig. 158.
Loosening and tightening the wheel
bolts
The wheel bolts must be loosened before rais­
ing the vehicle.
Fig. 159 Wheel change: loosening the wheel bolts
Loosening
• Fit the wheel bolt wrench over the wheel
bolt and push it down as far as it will go.
• Close your grip around the
end of the
wrench handle for maximum torque and
turn the wheel bolts
counter-clockwise
about one single turn in the direction of ar -
row
r:!> fig. 159. .,..