2012 RENAULT PULSE warning


> (GLW    0RGHO .$2(0B5HQDXOW @
ignition switch position will change to “ACC”.
NOTE:
.When the ignition switch is pushed to the
“ACC” or“ON” position or the engine is
started by the above procedures, the Intel-
ligent Key battery discharge indicator ap-
pears (on the Vehicle information display) or
the Intelligent Key system warning light may
blink in yellow (on the meter) even if the
Intelligent Key is inside the vehicle. This is
not a malfunction. To stop the warning light
from blinking, touch the ignition switch with
the Intelligent Key again.
. If the Intelligent Key battery discharge
indicator appears (on the Vehicle informa-
tion display) or the Intelligent Key system
warning light in the meter is blinking in
green, replace the battery as soon as
possible. (See “Battery”(P.8-23) .)GA\fOLI\bE E\bGI\bE
1. Apply the parking brake.
2. Depress the foot brake pedal.
3.Automatic Transmission (AT)/Continuously
Variable Transmission (CVT) model:
Move the selector lever to the “P” (Park) or “\b”
(\beutral) position.
The starter is designed to operate only when
the selector lever is in the proper position.
Manual Transmission (MT) model:
Move the shift lever to the “\b” (\beutral) position,
and depress the clutch pedal to the floor while
starting the engine.
The starter is designed to not operate unless
the clutch pedal is depressed.
4. Crank the engine with your foot off the accelerator pedal by turning the ignition switch to the “\fTART”
position.
5. Immediately release the ignition switch when the engine starts. If the engine starts, but fails to run,
repeat the above procedures.
If the engine is very hard to start in extremely cold
or hot weather, depress the accelerator pedal and
hold it to help start the engine.
CAUTION:
.Do not operate the starter for more than 15
seconds at a time. If the engine does not
start, turn the ignition switch off and wait 10
seconds before cranking the engine again.
Otherwise, the starter could be damaged.
. If it becomes necessary to start the engine
with a booster battery and jumper cables, the instructions and cautions contained in
the “6. In case of emergency” section should
be carefully followed.
6. Allow the engine to idle for at least 30 seconds after starting the engine to warm-up. Drive at
moderate speeds for a short distance first,
especially in cold weather.
CAUTION:
Do not leave the vehicle unattended while the
engine is warming up.
DIE\fEL E\bGI\bE
1. Apply the parking brake.
2. Depress the foot brake pedal.
3. Move the shift lever to the “\b” (\beutral) position,and depress the clutch pedal to the floor while
starting the engine.
4. Turn the ignition switch to the “O\b” position and wait until the glow plug indicator light
turns
off.
5. Crank the engine with your foot off the accelerator pedal by turning the ignition switch to the “\fTART”
position.
6. Immediately release the ignition switch when the engine starts. If the engine starts, but fails to run,
repeat the above procedures.
CAUTION:
.Do not operate the starter for more than 20
seconds at a time. If the engine does not
start, turn the ignition switch off and wait 20
seconds before cranking the engine again.
Otherwise, the starter could be damaged.
Starting and driving5-9
STARTING ENGINE (model without
Intelligent Key system)
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
5-12Starting and driving
.When stopping the vehicle on an uphill
grade, do not hold the vehicle by depressing
the accelerator pedal. The foot brake pedal
should be depressed in this situation.
Starting vehicle
1. After \ftarting the engine, fully \bepre\f\f the foot
brake pe\bal before \fhifting the \felector lever out
of the “P” (Park) po\fition.
2. Keep the foot brake pe\bal \bepre\f\fe\b an\b move the \felector lever to a \briving po\fition.
3. Relea\fe the parking brake, the foot brake pe\bal, an\b then gra\bually \ftart the vehicle in motion.
The AT is designed so the foot brake pedal
MUST be depressed before shifting from the “P”
(Park) position to any driving position while the
ignition switch is in the “ON”position.
The selector lever cannot be moved out of the
“P” (Park) position and into any of the other gear
positions if the ignition switch is turned to the
“LOCK” ,“OFF” or“ACC” position or if the key is
removed.
CAUTION:
. DEPRESS THE FOOT BRAKE PEDAL - Shift-
ing the selector lever to “D”, “R”, “2” or “1”
without depressing the foot brake pedal
causes the vehicle to move slowly when
the engine is running. Make sure the foot
brake pedal is depressed fully and the
vehicle is stopped before shifting the selec-
tor lever.
. MAKE SURE OF THE SELECTOR LEVER
POSITION - Make sure the selector lever is
in the desired position. “D”, “2” and “1” are
used to move forward and “R” to back up. .
WARM UP THE ENGINE - Due to the higher
idle speeds when the engine is cold, extra
caution must be exercised when shifting the
selector lever into the driving position
immediately after starting the engine.
Shifting gear
JVS0008XLeft-Hand Drive (LHD) model
JVS0009XRight-Hand Drive (RHD) model
: Pu\fh the button*Awhile \bepre\f\fing the
foot brake pe\bal.
: Pu\fh the button*A.
: Ju\ft move the \felector lever.
WARNING:
. Apply the parking brake if the selector lever
is in any position while the engine is not
running. Failure to do so could cause the
vehicle to move unexpectedly or roll away
and result in serious personal injury or
property damage.
. If the selector lever cannot be moved from
the P (Park) position while the engine is
running and the foot brake pedal is de-
pressed, the stop lights may not work.
Malfunctioning stop lights could cause an
accident injuring yourself and others.
After \ftarting the engine, fully \bepre\f\f the foot brake
pe\bal, pu\fh the \felector lever button an\b move the
\felector lever out of the P (Park) po\fition.
If the ignition \fwitch i\f the OFF or ACC po\fition for any
rea\fon while the \felector lever i\f in any po\fition\f other
than the P (Park) po\fition, the ignition \fwitch cannot
be turne\b to the LOCK po\fition.
If the ignition \fwitch cannot be the LOCK po\fition,
perform the following \ftep\f:
1. Apply the parking brake.
2. Place the ignition \fwitch in the ON po\fition while \bepre\f\fing the foot brake pe\bal.
3. Move the \felector lever to the P (Park) po\fition.
4. Mo\bel with Intelligent Key \fy\ftem: Place the ignition \fwitch in the OFF po\fition.
Mo\bel without Intelligent Key \fy\ftem: Place the
ignition \fwitch in the LOCK po\fition.
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
5-14Starting and driving
JVS0014XRight-Hand Drive (RHD) modelTo release the shi\ft lock, \ber\form the \following
\brocedure
1. Models with Intelligent KEY system: Place theignition switch in the “OFF” or “LOCK” \bosition.
Models without Intelligent KEY system: Place the
ignition switch in the “LOCK” \bosition and remove
the key.
2. A\b\bly the \barking brake.
3. De\bress the shi\ft lock release button.
4. Push and hold the selector lever button and move the selector lever to the “N” (Neutral) \bosition
while holding down the shi\ft lock release button.
5. Place the ignition switch to the “ON” \bosition to release the steering wheel lock.
The vehicle may be moved, by \bushing, to the desired
location.
I\f the selector lever cannot be moved out o\f the “P”
(Park) \bosition, have a RENAULT dealer check the AT
system as soon as \bossible.
Fail-sa\fe
When the \fail-sa\fe o\beration occurs, the AT will be
locked in third gear.
If the vehicle is driven under extreme conditions,
such as excessive wheel spinning and subse-
quent hard braking, the fail-safe system may be
activated. This will occur even if all electrical
circuits are functioning properly. In this case,
turn the ignition switch off and wait for 3
seconds. Then turn the ignition switch back to
the “ON” position. The vehicle should return to
its normal operating condition. If it does not
return to its normal operating condition, have a
RENAULT dealer check the transmission and
repair it if necessary.
DRIVING WITH CONTINUOUSLY VARI-
ABLE TRANSMISSION (CVT)
The Continuously Variable Transmission (CVT) in your
vehicle is electronically controlled to \broduce maximum
\bower and smooth o\beration.
The recommended o\berating \brocedures \for this
transmission are shown on the \following \bages. Follow
these \brocedures \for maximum vehicle \ber\formance
and driving enjoyment.
WARNING:
Do not downshift abruptly on slippery roads.
This may cause a loss of control.
CAUTION:
. The cold engine idle speed is high, so use
caution when shifting the transmission into
a forward or reverse position before the
engine has warmed up. .
Avoid revving up the engine while the
vehicle is stopped. This could cause unex-
pected vehicle movement.
. Never shift to either the “P” (Park) or “R”
(Reverse) position while the vehicle is mov-
ing. This could cause serious damage to the
transmission.
. Start the engine in either the “P” (Park) or
“N” (Neutral) position. The engine will not
start in any other position. If it does, have
your vehicle checked by a RENAULT dealer.
. Shift into the “P” (Park) position and apply
the parking brake when at a standstill for
longer than a short waiting period.
. Keep the engine at idling speed while
shifting from the “N” (Neutral) position to
any driving position.
. When stopping the vehicle on an uphill
grade, do not hold the vehicle by depressing
the accelerator pedal. The foot brake pedal
should be depressed in this situation.
Starting vehicle
1. A\fter starting the engine, \fully de\bress the \foot
brake \bedal be\fore moving the selector lever out
o\f the “P” (Park) \bosition.
2. Kee\b the \foot brake \bedal de\bressed and move the selector lever to a driving \bosition.
3. Release the \barking brake, the \foot brake \bedal, and then gradually start the vehicle in motion.
The CVT is designed so the foot brake pedal
MUST be depressed before shifting from the “P”
(Park) position to any driving position while the
ignition switch is in the “ON”position.
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
The selector lever cannot be moved out of the
“P”(Park) position and into any of the other
positions if the ignition switch is placed in the
“LOCK” ,“OFF” or“ACC” position or if the key is
removed.
CAUTION:
. DEPRESS THE FOOT BRAKE PEDAL - Shift-
ing the selector lever to “D”, “R” or “L”
without depressing the foot brake pedal
causes the vehicle to move slowly when
the engine is running. Make sure the foot
brake pedal is depressed fully and the
vehicle is stopped before shifting the selec-
tor lever.
. MAKE SURE OF THE SELECTOR LEVER
POSITION - Make sure the selector lever is
in the desired position. “D” and “L” are used
to move forward and “R” to back up.
. WARM UP THE ENGINE - Due to the higher
idle speeds when the engine is cold, extra
caution must be exercised when shifting the
selector lever into the driving position
immediately after starting the engine.
JVS0011XLeft-Hand Drive (LHD) model
JVC0026XRight-Hand Drive (RHD) model
: Push the butt\fn*Awhi\be depressing the
f\f\ft brake peda\b.
: Push the butt\fn*A.
: Just m\fve the se\bect\fr \bever.
Shifting
WARNING:
. Apply the parking brake if the selector lever
is in any position while the engine is not
running. Failure to do so could cause the
vehicle to move unexpectedly or roll away
and result in serious personal injury or
property damage.
. If the selector lever cannot be moved from
the “P”(Park) position while the engine is
running and the foot brake pedal is de-
pressed, the stop lights may not work.
Malfunctioning stop lights could cause an
accident injuring yourself and others.
After starting the engine, fu\b\by depress the f\f\ft brake
peda\b, push the se\bect\fr \bever butt\fn and m\fve the
se\bect\fr \bever \fut \ff the “P” (Park) p\fsiti\fn.
If the igniti\fn switch is p\baced in the “OFF” \fr “ACC”
p\fsiti\fn f\fr any reas\fn whi\be the se\bect\fr \bever is in any
p\fsiti\fns \fther than the “P” (Park) p\fsiti\fn, the igniti\fn
switch cann\ft be p\baced in the “LOCK” p\fsiti\fn.
If the igniti\fn switch cann\ft be p\baced in the “LOCK”
p\fsiti\fn, perf\frm the f\f\b\b\fwing steps:
1. App\by the parking brake.
2. P\bace the igniti\fn switch in the “ON” p\fsiti\fn whi\be depressing the f\f\ft brake peda\b.
3. M\fve the se\bect\fr \bever t\f the “P” (Park) p\fsiti\fn.
4. M\fde\bs with Inte\b\bigent Key system: P\bace the igniti\fn switch in the “OFF” p\fsiti\fn.
M\fde\bs with\fut Inte\b\bigent Key system:
P\bace the igniti\fn switch in the “LOCK” p\fsiti\fn.
Starting and driving5-15
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
5. Place the ignition switch in the “ON” \fosition tounlock the steering wheel.
\bhe vehicle may be moved to the desired location.
Re\flace the removed shift lock release cover after the
o\feration.
For model with Intelligent Key system: If the battery is
discharged com\fletely, the steering wheel cannot be
unlocked. Do not move the vehicle with the steering
wheel locked.
If the selector lever cannot be moved out of the “P”
(Park) \fosition, have a RENAUL\b dealer check the
CV\b system as soon as \fossible.
WARNING:
If the selector lever cannot be moved from the
“P” (Park) position while the engine is running
and the brake pedal is depressed, the stop lights
may not work. Malfunctioning stop lights could
cause an accident injuring yourself and others.
High fluid tem\ferature \frotection mode
\bhis transmission has a high fluid tem\ferature \frotec-
tion mode. If the fluid tem\ferature becomes too high
(for exam\fle, when climbing stee\f grades in high
tem\ferature with heavy loads, such as when towing a
trailer) , engine \fower and, under some conditions,
vehicle s\feed will be decreased automatically to
reduce the chance of transmission damage. Vehicle
s\feed can be controlled with the accelerator \fedal,
but engine and vehicle s\feed may be limited.
Fail-safe
When the fail-safe o\feration occurs, the CV\b will not
be shifted to the selected driving \fosition.
If the vehicle is driven under extreme conditions,
such as excessive wheel spinning and subse-
quent hard braking, the fail-safe system may be
activated. This will occur even if all electrical
circuits are functioning properly. In this case,
place the ignition switch in the “OFF”position
and wait for 10 seconds. Then turn the ignition
switch back to the “ON”position. The vehicle
should return to its normal operating condition.
If it does not return to its normal operating
condition, have a RENAULT dealer check the
transmission and repair it if necessary.
WARNING:
When the fail-safe operation occurs, vehicle
speed may be gradually reduced. The reduced
speed may be lower than other traffic, which
could increase the chance of a collision. Be
especially careful when driving. If necessary, pull
to the side of the road at a safe place and allow
the transmission to return to normal operation,
or have it repaired if necessary.
DRIVING WI\bH MANUAL \bRANSMISSION
(M\b)
WARNING:
. Do not downshift abruptly on slippery roads.
This may cause a loss of vehicle control.
. Do not over-rev the engine when shifting to
a lower gear. This may cause a loss of
vehicle control or engine damage.
CAUTION:
.Do not rest your foot on the clutch pedal
while driving. This may damage the clutch
system.
. Fully depress the clutch pedal before shift-
ing to help prevent transmission damage.
. Stop the vehicle completely before shifting
into the “R” (Reverse) position.
. When the vehicle is stopped for a period of
time, for example waiting at stoplights, shift
to the “N” (Neutral) position and release the
clutch pedal with the foot brake pedal
depressed.
. Do not shift to the "N" (Neutral) position
while driving. Doing so may result in an
accident due to loss of engine braking.
Starting and driving5-17
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
5-20Starting and driving
.when the selector lever is in the "R" (Reverse\f
position.
. when the rear \befogger is turne\b on.
. when the air con\bitioner is turne\b on.
. when the Electric power steering warning light or
the Anti-lock Braking System (ABS\f warning light
(if equippe\b\f illuminate.
. when the brake pe\bal is not \bepresse\b.
. when stopping the vehicle on sloping roa\bs.
. when the power consumption is large.
NOTE:
It may take some time until Idling Stop System
activates under the following conditions:
. when the battery is \bischarge\b.
. when the outsi\be temperature is low.
. when the battery is replace\b or the battery
terminal is \bisconnecte\b for exten\be\b perio\bs
an\b then reconnecte\b.
NOTE:
The engine will not restart with releasing the
brake pedal while Idling Stop System is acti-
vated under the following condition:
. when the selector lever is in the "P" (Park\f
position.
NOTE:
The engine will restart without releasing the
brake pedal while Idling Stop System is acti-
vated under the following conditions:
. when the rear \befogger is turne\b on.
. when the air con\bitioner is turne\b on.
. when the accelerator pe\bal is \bepresse\b. .
when the steering wheel is operate\b.
. when the battery capacity is low.
. when the power consumption is large.
. when the brake pe\bal is release\b on sloping roa\bs
an\b the vehicle is move\b.
. when the brake pe\bal is release\b with the selector
lever in the "D" (Drive\f or "N" (Neutral\f position.
. when the selector lever is place\b in the "L" (Low\f ,
"D" (Drive\f or "R" (Reverse\f position from the "N"
or "P" position.
. When the negative pressure of the brake system is
not sufficiently applie\b by \bepressing the brake
pe\bal several times.
Use this system while waiting at stoplight, etc. When
the vehicle is stoppe\b for long perio\bs of time, turn off
the engine.
When the engine hoo\b is opene\b with I\bling Stop
System on, the engine will be in the normal stoppe\b
state with the buzzer soun\bing. In this case, restart the
engine with the ignition switch.
When the \briver’s \boor is opene\b with I\bling Stop
System on, I\bling Stop System continues to be
activate\b although the buzzer soun\bs an\b the I\bling
Stop System in\bicator light blinks.
OPERATING IDLING STOP SYSTEM
NOTE:
. The engine stops automatically when the
brake pedal is depressed with the selector
lever in the "D" (Drive) position.
. When the brake pedal is released, the
engine restarts automatically.
. When the Idling Stop System is activated,
the Idling Stop System indicator light illu-
minates in the meter. .
The buzzer sounds and the indicator light
appears in the meter, indicating the condi-
tion of the Idling Stop System. For more
details, see “Stop/Start System indicator
light (if equipped for Europe)/Idling Stop
System indicator light (if equipped for Thai-
land)” (P.2-18) or “Idling Stop System remin-
der buzzer (if equipped for Thailand)” (P.2-
19) .
. The accumulated time of Idling Stop System
and the current saved fuel consumption by
Idling Stop System can be checked using the
drive computer, see “Accumulated time and
current saved fuel consumption (ml (mili-
liter)) by Idling Stop System (if equipped for
Thailand)” (P.2-27) .
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
JVS0075XType BThe information is \fisplaye\f an\f a \buzzer soun\fe\f to
remin\f the \friver to turn the ignition OFF to avoi\f a flat
\battery
The message can only \be cleare\f \by turning or
pushing the ignition OFF (or restarting the engine) .
PRECAUTIONS ON STOP/START
JVS0076X
The message is \fisplaye\f when there may \be some-
thing wrong with the Stop/Start System. You are
a\fvise\f to have the system checke\f \by a RENAULT
\fealer or qualifie\f workshop.Vehicle information display:
1. System fault warning
Instrument panel: 2. Stop/Start System in\ficator light
The message can \be cleare\f \by pressing the
\button.
NOTE:
The Stop/Start System indicator in the meter
flashes whilst the fault condition remains.
STOP/START SYSTEM OFF SWITCH
JVS0072X
The system can \be temporarily \fisengage\f \by press-
ing the Stop/Start System OFF switch. Pressing the
\button a secon\f time will re-engage the Stop/Start
System.
. When the Stop/Start System is \fisengage\f whilst
the engine is running, the engine is prevente\f from
automatically stopping.
. When the Stop/Start System is \fisengage\f after
the engine has \been automatically stoppe\f \by the
Stop/Start System, the engine will imme\fiately
restart if suita\ble con\fitions are present as
\fescri\be\f un\fer NORMAL OPERATION. The
engine will then \be prevente\f from automatically stopping \furing the same journey.
. Whenever the Stop/Start System is \fisengage\f
the in\ficator light on the Stop/Start System OFF
switch illuminates. In this con\fition the Stop/Start
System cannot prevent unnecessary fuel con-
sumption, exhaust emissions, or noise \furing your
journey.
NOTE:
The following messages may be displayed for a
few seconds in the vehicle information display
when the Stop/Start System OFF switch is
pressed.
More information a\bout the Stop/Start System can \be
checke\f using the [Settings] menu. (See “Vehicle
information \fisplay” (P.2-20) a\bout the \fisplay.)
Starting and driving5-23
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
5-24Starting and driving
WARNING:
.The VDC system is designed to help improve
driving stability but does not prevent acci-
dents due to abrupt steering operation at
high speeds or due to careless or dangerous
driving techniques. Reduce vehicle speed
and be especially careful when driving and
cornering on slippery surfaces and always
drive carefully.
. Do not modify the vehicle’s suspension. If
suspension parts such as shock absorbers,
struts, springs, stabilizer bars, bushings and
wheels are not RENAULT-approved or are
extremely deteriorated, the VDC system may
not operate properly. This could adversely
affect vehicle handling performance, and the
“VDC OFF” indicator or “SLIP”indicator or
both indicator lights may illuminate.
. If brake related parts such as brake pads,
rotors and calipers are not standard equip-
ment or are extremely deteriorated, the
“VDC OFF” indicator or “SLIP”indicator or
both indicator lights may illuminate.
. If engine related parts such as a muffler are
not standard equipment or are extremely
deteriorated, the “VDC OFF” indicator or
“ SLIP ”indicator or both indicator lights
may illuminate.
. When driving on extremely inclined surfaces
such as higher banked corners, the VDC
system may not operate properly and the
“VDC OFF” indicator or “SLIP”indicator or
both indicator lights may illuminate. Do not
drive on these types of roads. .
When driving on unstable surfaces such as a
turntable, ferry, elevator or ramp, the “VDC
OFF” indicator or “SLIP”indicator or both
indicator lights may illuminate. This is not a
malfunction. Restart the engine after driving
onto a stable surface.
. If wheels or tires other than those recom-
mended are used, the VDC system may not
operate properly and “VDC OFF”indicator or
“SLIP” indicator or both indicator lights may
illuminate.
. The VDC system is not a substitute for winter
tires or tire chains on a snowcovered road.
When accelerating or \friving on slipper\b surfaces, the
tires ma\b spin or sli\fe. With the Vehicle D\bnamic
Control (VDC) s\bstem, sensors \fetect these move-
ments an\f control the braking an\f engine output to
help improve vehicle stabilit\b.
. When the VDC s\bstem is operating, the “SLIP”
in\ficator in the instrument panel blinks.
. If the “SLIP” in\ficator blinks, the roa\f con\fitions
are slipper\b. Be sure to a\fjust \bour spee\f an\f
\friving to these con\fitions. Be sure to \frive
carefull\b. (See “Slip in\ficator light” (P.2-17)
an\f“Vehicle D\bnamic Control (VDC) off in\ficator
light” (P.2-18) .)
. In\ficator light
If a malfunction occurs in the s\bstem, the “SLIP”
an\f “VDC OFF” in\ficator lights illuminate in the
instrument panel. As long as these in\ficators are
illuminate\f, the VDC s\bstem function is cancele\f.
The VDC s\bstem uses a Brake Limite\f Slip Differential
(BLSD) function to improve vehicle traction. The BLSD
s\bstem works when one of the \friving wheels is
spinning on a slipper\b surface. The BLSD s\bstem
brakes the spinning wheel, which \fistributes the \friving power to the other \frive wheel. If the vehicle
is operate\f with the VDC OFF switch pushe\f an\f the
VDC s\bstem turne\f off, all VDC s\bstems will be turne\f
off. The BLSD s\bstem will still operate with the VDC
s\bstem off. If the BLSD s\bstem is activate\f, the “SLIP”
in\ficator light will blink an\f \bou ma\b hear a clunk noise
an\f/or feel a pulsation in the foot brake pe\fal. This is
normal an\f is not an in\fication of a malfunction. While
the VDC s\bstem is operating, \bou ma\b feel a pulsation
in the foot brake pe\fal an\f hear a noise or feel a
vibration from un\fer the hoo\f. This is normal an\f
in\ficates that the VDC s\bstem is working properl\b.
The VDC s\bstem computer has a built-in \fiagnostic
feature that tests the s\bstem each time \bou start the
engine an\f move the vehicle at a low spee\f forwar\f or
backwar\f. When the self-test occurs, \bou ma\b hear a
“clunk” noise an\f/or feel a pulsation in the foot brake
pe\fal. This is normal an\f is not an in\fication of a
malfunction.
VEHICLE DYNAMIC CONTROL (VDC) OFF
SWITCH
SIC1881
The vehicle shoul\f be \friven with the Vehicle D\bnamic
Control (VDC) s\bstem ON for most \friving con\fitions.
When the vehicle is stuck in mu\f or snow, the VDC
VEHICLE DYNAMIC CONTROL (VDC)
SYSTEM (if equipped except for
Europe)
&RQGLWLRQ