2012 Peugeot 208 Owner's Manual - RHD (UK, Australia)

159
7
Practical information
Changing front foglamp / directional lamps
) Access to the front foglamp is through theorifice below the bumper.)
Disconnect the bulb holder connector by pressing on the top of the tongue. )
Extract the bulb holder by pressing on the
two clips clips (top and bottom).) Replace the module.
To reassemble, carry out these operations in
r
everse order.
Changing integrated direction indicator side repeater bulbs
) Press the central tongue and remove theside repeater. i)
Pull the bulb holder out and replace the failed bulb.
To reassemble, carry out these operations in
reverse order.
You should contact a PEUGEOT dealer or a qualified workshop for the replacement of these bulbs.
)
Insert a flat screwdriver between the mirror glass and its base.)
Use the screwdriver as a lever to extract
the mirror glass.) Unclip the mirror shell by pressing on the
two retaining clips.
To obtain this module, contact aPEUGEOT dealer or a qualifiedworkshop. You can also contact a PEUGEOT dealer or a qualified workshop for thisreplacement.

160
Practical information
Brake lamps (P21W).2.Reversing lamps (R10W).3. Direction indicators (PY21W amber).4.Sidelamps (light emitting diodes -LEDs).
Rear lamps


Changing the light emittingdiode-LED lamps i

For replacement, contact a PEUGEOT dealer
or qualified workshop.
5
.Foglamp (P21W).

161
7
Practical information
Changing brake lamp, reversing lamp and direction indicator bulbs
These three bulbs are changed from inside the boot:
)open the boot, )remove the access grille from the corresponding side trim panel,)slacken and remove the nut,)disconnect the lamp unit connector, )unclip the lamp unit carefully extract itpulling in line towards the outside,
)
press the four tabs and remove the bulbholder,)
turn the bulb a quar ter of a turn and change it.
To reassemble, carry out these operations inreverse order.
Take care to engage the lamp unit in its guides,while keeping it in line with the vehicle.
Tighten sufficiently to ensure sealing, but without damaging the lamp.

162
Practical information
Changing the third brake lamp
bulbs
)Unscrew the fixing pins on each side of the lamp, without removing them completely.)Push on the screws to unclip the lamp.
)Disconnect the lamp connector.)Remove the lamp from the outside. )Turn the bulb holder which corresponds
to the faulty bulb one quar ter of a turn and remove it.)Pull the bulb and change it.
To r e f i t , c a r ry out these operations in reverse order.
Number plate lamps
To facilitate the removal of the lamp, carry out
this operation with the tailgate half open.
) Insert a thin screwdriver into the lenscutout. )
Push it outwards. )
Remove the lens. )
Change the faulty bulb.
To refit, press on the lens to clip it in place.
Access is by passing a hand under the bumper. )Turn the bulb holder a quarter of a turn and
pull it out. )Disconnect the connector on the bulb holder. )Pull the bulb out and change it.
To r e f i t , c a r ry out these operations in reverse order.
You can also contact a PEUGEOT dealer or a qualified workshop for the replacement of thesebulbs.

Changing a foglamp bulb

163
7
Practical information




















Changing a fuse

The extraction tweezer is fitted to the back of
the fusebox cover located inside the glove box. )Open the glove box lid,)unclip the fusebox cover by pulling at the
top right,
)disengage the cover completely and turn it over,

Access to the tools
)
remove the carrier on which the tweezer isfitted.

164
Practical information
To replace a fuse, you must: )use the special tweezer to extract the fuse
from its housing and check the condition of its filament.)always replace the failed fuse with a fuse
of the same rating (same colour); using a
different rating could cause faults (risk of fire).
If the fuse fails again soon after replacement,have the vehicle's electrical system checked bya PEUGEOT dealer or a qualified workshop.
Changing a fuse
Before changing a fuse:
)the cause of the failure must be identifiedand rectified, )all electrical consumers must be switched
off, )the vehicle must be immobilised with theignition off,)identify the failed fuse using the tables andlayout drawings in the following pages.Good Failed
PEUGEOT will not accept responsibilityfor the cost incurred in repairing your vehicle or for rectifying malfunctions resulting from the installation of accessories not supplied and not
recommended by PEUGEOT andnot installed in accordance with its instructions, in par ticular when thecombined consumption of all of the additional equipment connectedexceeds 10 milliamperes.



Installing electricalaccessories

Your vehicle's electrical system isdesigned to operate with standard or optional equipment.
Before installing other electrical equipment or accessories on your vehicle, contact a PEUGEOT dealer or a qualified workshop.
The replacement of a fuse not shown in the tables below may cause a serious malfunction of your vehicle. Contacta PEUGEOT dealer or a qualified workshop.

Tweezer

165
7
Practical information
The fusebox is placed in the lower dashboard(right-hand side).


Access to the fuses
)Refer to the paragraph "Access to the tools".
Fuse N°RatingFunctions
F0
140 A Heated rear window.
F02 10 A
Heated door mirrors.
F0
330 A Front one-touch windows.
F0
4- Not used.
F05
30 A Rear one-touch windows.
F0
610 A Folding door mirrors.
F0
710 A
Folding door mirrors.
F0
8- Not used.
F0
9- Not used.
F1
020 A Hi-Fi amplifier.
F11-
Not used.
F12
- Not used.
Fuse tables

166
Practical information
Fuse N°RatingFunctions
F02 5
A Door mirrors, headlamps, diagnostic socket.
F09 5
A Alarm.
F1
05 A Independent telematic unit, trailer interface.
F115 A Electrochrome rear view mirror, additional heating.
F13 5
A Hi-Fi amplifier, parking sensors
F1
615 A
Front 12 V socket.
F17 15 A
Audio system, audio system
(accessory).
F18
20 A To u c h screen.
Fuses in the glove box