2012 Peugeot 208 Owner's Manual - RHD (UK, Australia)

87
4
Driving

Never select neutral N
while the vehicleis moving. Only engage reverse gear Rwhen thevehicle is immobilised, with your foot on the brake pedal. In all cases, you must apply the parkingbrake to immobilise the vehicle.



"Au t o s equential" mode

In the automated mode, you can resumecontrol temporarily at any time using thesteering mounted control paddles.
The use of these paddles permits manual
selection of the gears in situations which
require a more rapid change-down than in
the automated mode (arrival at a roundabout,leaving a car park with a steep gradient,
over taking...).
The gearbox engages the required gear if
the engine speed permits. AUTO
remains
displayed on the instrument panel.
After a few moments, the gearbox resumes
automatic control of the gears.
"Snow" automated mode
In the automated mode, if the vehicle detects poor grip, the gearbox will change automatically
to the automated "snow" mode.
AUTO
and 7
appear in the
instrument panel.
Reinitialisation
Following disconnection of the battery, the gearbox must be reinitialised.) Switch on the ignition.
AUTO , 7and -appear in the instrument panel.


Operating fault

With the ignition on, if this warninglamp comes on and AUTOflashes, accompanied by an
audible signal and a message in the screen,
this indicates a
gearbox fault.
Have it checked by a PEUGEOT dealer or a qualified workshop.


For best acceleration, when over taking another vehicle for example, press the accelerator pedal firmly to pass the
point of resistance.

Stopping the vehicle
Before switching off the engine, you canchange to position N
to be in neutral.
In this case, you must apply the parking brake to immobilise the vehicle.
)
Select position N.)
Press the brake pedal.)
Wait approximately 30 seconds until Nor a gear appears in the instrument panel. )
Release the brake pedal.
The gearbox is operational again.

88
Driving














6-speed electronic gear control gearbox
Six-speed electronic gear control gearbox
which offers a choice between the comfort of
fully automatic operation or the pleasure of manual gear changing.There are two driving modes: -automatedmode for automatic control of
the gears by the gearbox,- manualmode for sequential gear changing
by the driver.
For each of these two modes, a Sport
settingis available, providing a more dynamic driving style.
In automated mode, it remains possible to
change gear manually by using the steering mounted control paddles when required, when
over taking, for example.

Gear lever
R.
Reverse )
With your foot on the brake, lift the lever
and push forwards.N.Neutral.) With your foot on the brake, select thisposition to star t.
A. Automatic mode.)
Move the lever backwards to select this
mode. M. + / -.
Manual mode with sequential gear changing.)
Move the lever to the left to select this
mode, then:


- push it for wards to change up,

- or pull it backwards to change down.
S.
Sport setting.)
Press this button to switch it on or off.+
.Change up paddle. )Press the back of the "+"
steering mounted paddle to change up a gear.-.
Change down paddle. )Press the back of the "-"steering mounted paddle to change down a gear.


Steering mounted control paddles


The steering mounted paddles cannotbe used to select neutral, or to engageor disengage reverse gear.

Do not drive with your hand resting on the gear lever as there is a risk of damaging the electronic gearbox.

89
4
Driving

Engagement of reverse gear isaccompanied by an audible signal.
Nflashes in the instrument panel,accompanied by an audible signaland a message in the instrument panel screen, if the gear lever is not inposition N
on starting.


For optimum acceleration, for example when over taking another vehicle, pressthe accelerator pedal firmly past the point of resistance.



Display in the instrument panel Moving off
Automated mode


Gear lever positions
N.
Neutral
R.Reverse 1, 2, 3, 4, 5, 6.Gears in manual mode
AUTO. This comes on when the automaticmode is selected. It switches off on changing to manual mode.
S.Sport (Sport setting).
) Place your foot on the brakewhen
this warning lamp is flashing (for example, when star ting the engine).

)
Select position N.)
Press the brake pedal down fully. )
Start the engine.
Nappears in the instrument panelscreen.
)
Select automated mode (position A
), Amanual mode (position M ), or reverse(position R).R)
Release the parking brake.)
Ta k e your foot off the brake pedal, thenaccelerate.
AUTOand 1, 1
or R
appears in the instrument panel screen.
)
After star ting the vehicle, select position Afor enter automated mode.
AUTO
and the gear engaged appear
in the instrument
panel screen.
The
gearbox is then operating in auto-active
mode, without any action on the par t of the driver. It continuously selects the most suitablegear, depending on the:


- style of driving,

- profile of the road. Foot on brake
flashes on the instrument panel, accompanied by an audible signal and a message in the instrument panel screen, if the brakepedal is not pressed on starting.

90
Driving

At very low speed, if reverse gear is requested, this will only be takeninto account when the vehicle is immobilised. A warning lamp appears in the instrument panel screen.
Manual gear changing
Manual mode

On sharp acceleration, the gearbox willnot change up unless the driver acts onthe gear lever or the steering mounted paddles.
Never select neutral N
while the vehicleis moving.
Only engage reverse gear Rwhen thevehicle is immobilised with the brakepedal pressed. This selective
gear change mode enables you
to over take, for example, while still remaining in automatic mode.)Operate the +or - steering mounted controlpaddle.
The gearbox engages the gear requested if theengine speed permits. AUTOis still displayed
in the instrument panel.

After a few moments without any action on
the controls, the gearbox resumes automatic control of the gears.
) When the vehicle has moved off, select
pos
ition M to change to manual mode.


- Pull the lever towards the +sign
to change up a gear.

- P
ush the lever towards the -sign
to change down a gear.
The
gears engaged appear successively in the instrument panel screen.
The
gear change requests are only carried out
if the engine speed permits.
It is not necessary to release the accelerator
during gear changes.
When braking or slowing down, the gearbox
changes down automatically to permit
acceleration in the correct gear.

91
4
Driving

Sport setting

Operating fault
When immobilising the vehicle, with the engine running, you must place the gear lever in neutral N.Before carrying out any work in the engine compar tment, check that the gear lever is in neutral N
and that the parking brake is applied.


You must press the brake pedal when starting the engine.
Whatever the circumstances, you mustmanually apply the parking brake to immobilise the vehicle.

)After selection of manual or automated
mode, press the S
button to activate theSport setting, which provides a more
dynamic driving style. With the i
gnition on, the flashing
o
f this warning lamp and theflashing of AUTO
, accompanied
by an audible signal and a message in
the instrument panel screen, indicates a
malfunction of the
gearbox.
have it checked by PEUGEOT or a qualified
workshop.
S appears along side the gear engaged in the instrument panel screen.
)Press the Sbutton again to deactivate it. Sthen disappears from the instrument panelscreen.

Return to normal mode is automatic ever
y time
the ignition is switched off.

Stopping the vehicle
Before switching off the engine, you can
choose to:
- move to position N
to engage neutral,
- leave the gear engaged; in this case, it will
not be possible to move the vehicle.
In both cases,
you must apply the parkingbrake to immobilise the vehicle.

92
Driving
Four-speed automatic gearbox which offers a choice between the comfor t of fully automatic operation, enhanced by spor t and snow
pro
grammes, or manual gear changing.
There are therefore four driving modes:-automatic
operation for electronic management of the gears by the gearbox,
-
sportprogramme for a more dynamic style
of driving,

- snowprogramme to improve driving when
traction is poor,

- se
quentialoperation for manual changing
of the gears by the driver.















Automatic gearbox
1.
Gear lever.2.
Button "S"(sport)
.
3.Button "7"(snow).



Gear selection gateGear lever
P.Park.
- Immobilisation of the vehicle, parking brakeon or off.
- Starting the engine.
R. Reverse.
- Reversing manoeuvres, vehicle stationary, engine at idle.N.Neutral.
- Immobilisation of the vehicle, parking brakeon.
- Star ting the engine.D.
Automatic operation.M + / -. Manual operation with sequential changing of the four gears.)Push for wards to change up through the
gears.or )Pull backwards to change down through
the gears.



Displays in the instrument panel

When you move the lever in the gate to select
a position, the corresponding indicator is
displayed in the instrument panel. P. ParkR.ReverseN.
NeutralD.Drive (Automatic driving) S.Sportprogramme 7.Snowprogramme1 2 3 4.
Gears engaged during manual
operation
-. Invalid value during manual operation


Foot on brake
)
Press the brake pedal when this
indicator lamp is displayed in the
instrument panel
(e.g.: star tingthe engine).

93
4
Driving
)Apply the parking brake. )Select position P or N.)Star t the engine.
If this procedure is not followed, there is an
audible signal, accompanied by the display of
an warning message.)With the engine running, press the brake pedal. )Release the parking brake. )Select position R, Dor M.)Gradually release the brake pedal.
The vehicle moves off immediately.


Moving off


When the engine is running at idle, with the brakes released, if position R, D
or M
is selected, the vehicle moves evenwithout the accelerator being pressed.
When the engine is running, never leave children in the vehicle without supervision. When carrying out maintenance with the engine running, apply the parkingbrake and select position P
.
P


If position N
is selected inadver tently while driving, allow the engine toreturn to idle then select position D
toaccelerate.
Never select position N
while the vehicle is moving.Never select positions P
or Runless thevehicle is completely stationary.

Automatic operation
)
Select position Dfor automaticchanging
of the four gears.The gearbox then operates in auto-adaptivemode, without any inter vention on the par t
of the driver. It continuously selects the most suitable gear according to the style of
driving, the profile of the road and the load in
the vehicle.
For maximum acceleration without touching the gear lever, press the accelerator pedal downfully (kick down). The gearbox changes downautomatically or maintains the gear selecteduntil the maximum engine speed is reached.On braking, the gearbox changes downautomatically to provide efficient engine
braking.
If you release the accelerator sharply, thegearbox will not change to a higher gear for
safety reasons.

Sport and snow programmes


Sport programme "S"
)
Press button "S", after star ting the engine.
The
gearbox automatically favours a dynamic style of driving.
S
appears in the instrument panel.


Snow programme " 7"
)
Press button "7
", after star ting the engine.
The gearbox adapts to driving on slipperyroads.
This programme improves star ting and drive
when traction is poor.
7 appears in the instrument panel.



Return to automatic operation
)
At any time, press the button selected
again to quit the programme engaged and
return to auto-adaptive mode.
These two special programmes supplement the
automatic operation in very specific conditions of use.

94
Driving
Manual operation
)Select position M for sequentialchanging
o
f the four gears.)Push the lever towards the + sign tochange up a gear. )Pull the lever towards the -
sign to change
down a gear.
It is only possible to change from one gear to another if the vehicle speed and engine speedpermit; otherwise, the gearbox will operate
temporarily in automatic mode.
D disappears and the gears engaged appear in succession in the
instrument panel.

Invalid value during manual operation
This symbol is displayed if a gear
is not engaged correctly (selector
between two positions).



Stopping the vehicle

Before switching off the engine, you can engage
position P or N
to place the gearbox in neutral.
In both cases, apply the parking brake to
immobilise the vehicle.

Operating fault
When the ignition is on, thelighting of this warning lamp,
accompanied by an audible signal and a
message in the multifunction screen, indicates
a gearbox fault.
In this case, the gearbox switches to back-up mode and is locked in 3rd gear. You may feel
a substantial knock when changing from Pto Rand from N to R
. This will not cause any damage to the gearbox.
Do not exceed 60 mph (10 0 km/h), local speed
restrictions permitting.

Contact a PEUGEOT dealer or a qualified
workshop as soon as possible.
I
f the engine speed is too low or too high, the
gear selected flashes for a few seconds, then
the actual gear engaged is displayed.
It is possible to change from position D(automatic) to position M (manual) at any time.
When the vehicle is stationary or movingvery slowly, the gearbox selects gear M1automatically. The spor t and snow programmes do not
operate in manual mode.

There is a risk of damage to thegearbox:


- if you press the accelerator and brake pedals at the same time,

- if you force the movement of the gear lever from the Pposition toanother position when the battery isflat.
To reduce fuel consumption when at
a prolonged standstill with the enginerunning (traffic jam...), put the gear lever in the Nposition and apply the parkingbrake.

If the lever is not in position P
, when the Pdriver's door is opened or approximately 45 seconds after the ignition is switchedoff, a warning message appears in the screen.)Return the lever to position P; the
message disappears.