Page 402 of 442
Vehicle care and maintenance
7-39
7
3. Pull the bulb out of the socket. 4. To install the bulb, perform the removal steps in reverse.
NOTEWhen installing the light assembly, push in the end facing
the front of the vehicle first.*: Front of the vehicle
BK0140800US.book 39 ページ 2011年9月29日 木曜日 午後3時28分
Page 404 of 442
Vehicle care and maintenance
7-41
7
4. Remove the bulb as follows.
[Front turn signal light]
Pull the bulb out of the socket.
[Front fog light and daytime running light]
While holding down the tab (F), pull out the bulb assem-
bly (G).5. To install the bulb, perform the removal steps in reverse.Front fog light
Daytime running light Front turn signal light
CAUTION
!Handle halogen light bulb with care. The gas inside
a halogen light bulb is highly pressurized, so drop-
ping, knocking, or scratching a halogen light bulb
can cause it to shatter.Never hold the halogen light bulb with a bare hand,
dirty glove, etc.
The oil from your hand could cause the bulb to
break the next time the fog lights are used.
If the glass surface is dirty, clean it with alcohol and
let it dry completely before installing the bulb.
BK0140800US.book 41 ページ 2011年9月29日 木曜日 午後3時28分
Page 406 of 442
Vehicle care and maintenance
7-43
7
4. Turn the socket counterclockwise to remove it.NOTEThe tail and stop lights use LEDs rather than bulbs.
For repair and replacement, contact a certified i-MiEV
dealer.5. Pull the bulb out of the socket.
6. To install the bulb, perform the removal steps in reverse.C- Tail and stop light (LED) - cannot be replaced
D- Rear turn signal light
E- Back up light
BK0140800US.book 43 ページ 2011年9月29日 木曜日 午後3時28分
Page 407 of 442
7-44 Vehicle care and maintenance
7
Rear side-marker lights
N00935400108
1. Remove the clips (A), then lift the cover (B).2. Turn the socket (C) counterclockwise to remove it.
3. Pull the bulb out of the socket.
BK0140800US.book 44 ページ 2011年9月29日 木曜日 午後3時28分
Page 408 of 442
Vehicle care and maintenance
7-45
7
4. To install the bulb, perform the removal steps in reverse.
High-mounted stop light
N00943900115
1. Remove the mounting screws (A) and remove the light
unit.
BK0140800US.book 45 ページ 2011年9月29日 木曜日 午後3時28分
Page 409 of 442
7-46 Vehicle care and maintenance
7
2. While holding down the tab (B), pull out the connector. 3. Remove the screws (C) and then remove the bulb holder
(D).
BK0140800US.book 46 ページ 2011年9月29日 木曜日 午後3時28分
Page 410 of 442
Vehicle care and maintenance
7-47
7
4. Pull the bulb out of the socket.
5. To install the bulb, perform the removal steps in reverse.
License plate lights
N00944000399
1. When removing the light unit (A), push it toward the left
side of the vehicle body.
BK0140800US.book 47 ページ 2011年9月29日 木曜日 午後3時28分
Page 411 of 442
7-48 Vehicle care and maintenance
7
2. Use a flat blade screwdriver into the tab (B) and pry gen-
tly to remove the lens.3. Pull the bulb out of the socket.
BK0140800US.book 48 ページ 2011年9月29日 木曜日 午後3時28分