2012 MITSUBISHI iMiEV ignition

Features and controls
3-5
3
NOTE
Electronic immobilizer is not compatible with commer-
cially available remote starting systems. Use of commer-
cially available remote starting systems may result in
vehicle starting problems and a loss of security protection.

A system failure is suspected when the electric motor
switch is turned to the “START” position, and the electric
motor unit does not start. In such a case, contact a certified
i-MiEV dealer.Replacement keysOnly keys that have been programmed to the vehicle electron-
ics can be used to start the vehicle.
If you lose a key, you can order a key from a certified i-MiEV
dealer by referring to the key number.
To prevent vehicle theft, the ID code for the vehicle keys must
be changed.
Take your vehicle and all remaining keys to a certified i-MiEV
dealer to have your ID code changed.
Additional keysTo add a key, you need to register the ID code to the vehicle.
Registering the ID code can be done by a certified i-MiEV
dealer. Or it can be done by yourself (except for vehicles sold
in Canada).
To register the ID code yourself, follow the “Customer key
programming” procedure below.
If you choose to have a certified i-MiEV dealer register the ID
code, take your vehicle and any remaining keys to a certified i-
MiEV dealer.NOTE
You are provided with 2 keys, but you may add up to 6
more keys.Customer key programming (Except for vehicles
sold in Canada)
N00562200113
You can program new keys to the system if you have two valid
(already registered) keys and blank (not registered) immobi-
lizer key (specially cut for your vehicle at a certified i-MiEV
dealer) by doing the following:
1. Insert the first valid key into the ignition and turn the igni-
tion to the “ON” position for 5 seconds.
2. Turn the ignition to the “LOCK” position and remove the
first key.
3. Within 30 seconds of turning the first key to the “LOCK”
position, insert the second valid key into the ignition and
turn it to the “ON” position. About 10 seconds later, the
immobilizer indicator will start blinking.
CAUTION
!
Do not make any alterations or additions to the
immobilizer system. Alterations or additions could
cause failure of the immobilizer.
BK0140800US.book 5 ページ ２０１１年９月２９日　木曜日　午後３時２８分

3-6 Features and controls
3
4. When the immobilizer indicator starts blinking, turn the
second valid key to the “LOCK” position and remove it.
Within 30 seconds after doing so, insert a blank immobi-
lizer key into the ignition and turn it to the “ON” position.
Perform this operation no more than 30 seconds after the
immobilizer indicator starts blinking. When registration
of the ID code is complete, the immobilizer indicator will
come on for 3 seconds then go off. If an error occurs, the
immobilizer indicator will go off during the procedure.
5. If you wish to register another key, perform the process
again from step 1.
NOTE
It is not possible to register a key if:
• the immobilizer indicator goes off during the procedure
• the immobilizer indicator does not come on for 3 sec-
onds after turning the ignition to the “ON” position with
a blank immobilizer key

The procedure will be terminated automatically if:
• a period of 30 seconds or longer elapses from the
moment when the first key is turned to the “LOCK”
position to the moment when the second key is turned to
the “ON” position
• a period of 30 seconds or longer elapses from the
moment when the second key is turned to the “LOCK”
position to the moment when the blank immobilizer key
(specially cut for your vehicle at a certified i-MiEV
dealer) is turned to the “ON” position
• more than 20 seconds elapse after the immobilizer indi-
cator starts blinking
BK0140800US.book 6 ページ ２０１１年９月２９日　木曜日　午後３時２８分

For emergencies
6-3
6
2. Position the vehicles close enough together so that the
jumper cables can reach, but be sure the vehicles are not
touching each other.
3. Set the parking brake firmly on your vehicle and move the
selector lever into the “P” (PARK) position.
4. Set the parking brake firmly on the other vehicle. Put the
automatic transaxle in “P” (PARK) or the manual
transaxle in “N” (Neutral).
5. Turn the ignition switch (the electric motor switch) on
each vehicle to the “LOCK” position.NOTE
Turn off all lights, heater, and other electrical loads. This
will help avoid sparks.6. Remove the battery cover, and then make sure your 12V
starter battery electrolyte is at the proper level. (Refer to
“Checking 12V starter battery electrolyte level” on page
7-14.)
7. Connect one end of one jumper cable to the positive
(+) terminal of the discharged battery (A), and then con-
nect the other end to the positive (+) terminal of the
booster battery (B).
CAUTION
!
Check the other vehicle. It must have a 12V battery.
If the other system is not 12V, both systems can be
damaged.
WA R N I N G
!
If the electrolyte fluid is not visible, or looks frozen,
DO NOT ATTEMPT JUMP STARTING!!
The battery might split open or explode if the tem-
perature is below the freezing point or if it is not
filled to the proper level.
BK0140800US.book 3 ページ ２０１１年９月２９日　木曜日　午後３時２８分