2012 MITSUBISHI iMiEV maintenance reset

Features and controls
3-63
3
Trip odometer
N00572400020
The trip odometer shows the distance traveled since the last
time it was reset.
There are two trip odometer displays: and .
Trip odometer can be used to measure the distance traveled
since the current trip began.
At the same time, Trip odometer can be used to measure
the distance from a second location.NOTE
Even if the electric motor switch is turned to “ACC” or
“LOCK” position, the trip odometer will be displayed for
about 30 seconds after the reset button is pressed.
To reset the trip odometer
To zero the counter, press and hold the reset button for more
than 1 second. Only the currently displayed value will be reset.
If trip odometer is displayed, for example, only trip odom-
eter will be reset. NOTE
Both trip odometer and trip odometer can measure
trips up to 9999.9 miles/kilometers.

If the 12V starter battery is disconnected for a long time,
both of these displays will be reset to “0”.
Service reminder
N00572500021
The service reminder shows the driving distance or number of
months remaining until the next recommended periodic main-
tenance inspection is required.
When the next inspection is nearly due, the display shows “----
--”.NOTE
The service reminder time can be modified by a certified
i-MiEV dealer, to adjust for severe usage, etc. Refer to
“Severe maintenance schedule” in your vehicle’s War-
ranty and Maintenance Manual. For further information,
please contact a certified i-MiEV dealer.

Even if the electric motor switch is turned to “ACC” or
“LOCK” position, the service reminder will be displayed
for about 30 seconds after reset button is pressed.
BK0140800US.book 63 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Features and controls
3-65
3
Resetting the service reminder
With the electric motor switch in the “LOCK” position or the
“ACC” position, it is possible to reset the spanner mark (A)
and “------” indication (B).
When they have been reset, the driving distance or number of
months remaining until the next periodic inspection are shown
and the spanner mark (A) is no longer shown every time the
electric motor switch is turned from the “LOCK” position or
the “ACC” position to the “ON” position.1. Push the reset button (D) to view the driving distance or
number of months remaining until the next periodic
inspection.
2. Give the reset button (D) a long push (at least 2 seconds)
to make the spanner mark (A) start flashing. (If you do not
touch the reset button for about 10 seconds while the
spanner mark is flashing, the display will revert to its orig-
inal indication.)
3. Give the reset button (D) a gentle push while the spanner
mark is flashing. The “------” indication (B) will change to
“cLEAr” (C).
4. The driving distance or number of months remaining until
the next periodic inspection will be shown.
NOTE
It is not possible to reset the “------” indication (B) with
the electric motor switch in the “ON” position.

When a certain distance has been driven and a certain
period has elapsed after appearance of the “------” indica-
tion (B), the indication is automatically reset and the num-
ber of months until the next periodic inspection is shown.

If you accidentally reset the display, consult a certified
i-MiEV dealer for assistance.
CAUTION
!
The customer is responsible for making sure that
regular inspections and maintenance are performed.
Inspections and maintenance must be performed to
prevent accidents and malfunctions.
BK0140800US.book 65 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Vehicle care and maintenance
7-17
7
NOTE
Before cleaning the 12V starter battery, tighten all the
filler port caps to keep dirt and moisture out.

Check each 12V starter battery terminal for corrosion. If
necessary, clean the terminals with a solution of baking
soda and water. Grease the posts and clamps after clean-
ing or tightening them.

Check to see that the 12V starter battery is securely
installed and cannot be moved. Also check each terminal
for tightness.

If you will not be driving your vehicle for a long period of
time, remove the 12V starter battery and store it in a place
where the 12V starter battery fluid will not freeze. Mem-
ory data for settings made by the user may be erased when
the 12V starter battery is removed. If this happens, reset
the settings again using the relevant procedures. The 12V
starter battery only should be stored with a full charge.
WA R N I N G
!
Open doors and windows in any closed space where
you may be charging or working with the 12V
starter battery.
Always wear protective clothing and goggles when
working with the 12V starter battery, or have a
skilled automobile technician do it.
If you are quick-charging your 12V starter battery,
first disconnect the 12V starter battery cables.
In order to prevent a short circuit, be sure to discon-
nect the negative (-) terminal first, and reconnect it
last.
If the electrolyte level is very low, have the 12V
starter battery checked at a certified i-MiEV dealer.
12V starter battery terminals and related accesso-
ries contain lead and lead compounds. Wash hands
after handling.
CAUTION
!
When replacing the 12V starter battery, remove the
connected positive (+) and negative (-) terminals
after turning the electric motor switch to the
“LOCK” position and waiting at least 1 minute. If
the 12V starter battery terminal is removed just
after the electric motor switch is turned to the
“LOCK” position, this may cause damage to compo-
nents of the electric motor unit.
BK0140800US.book 17 ページ ２０１１年９月２９日　木曜日　午後３時２８分