2012 Lancia Thema ECO mode

brake pressure. This brake pressure
will not be noticed by the driver. The
brake system uses this brake pressure
to allow a fast brake response if the
driver applies the brakes.
RAIN BRAKE SUPPORT
Rain Brake Support may improve
braking performance in wet condi-
tions. It will periodically apply a small
amount of brake pressure to remove
any water buildup on the front brake
rotors. It only functions when the
windshield wipers are in the LO or HI
mode, it does not function in the in-
termittent mode. When Rain Brake
Support is active, there is no notifica-
tion to the driver and no driver inter-
action is required.
ESC ACTIVATION/
MALFUNCTION
INDICATOR LIGHT AND
ESC OFF INDICATOR
LIGHTThe “ESC Activation/
Malfunction Indicator
Light” in the instrument
cluster will come on when the ignition switch is turned to the ON
position. It should go out with the
engine running. If the “ESC
Activation/Malfunction Indicator
Light” comes on continuously with
the engine running, a malfunction has
been detected in the ESC system. If
this light remains on after several ig-
nition cycles, and the vehicle has been
driven several kilometers at speeds
greater than 48 km/h, see your autho-
rized dealer as soon as possible to
have the problem diagnosed and cor-
rected.
The “ESC Activation/Malfunction In-
dicator Light” (located in the instru-
ment cluster) starts to flash as soon as
the tires lose traction and the ESC
system becomes active. The “ESC
Activation/Malfunction Indicator
Light” also flashes when TCS is ac-
tive. If the “ESC Activation/
Malfunction Indicator Light” begins
to flash during acceleration, ease up
on the accelerator and apply as little
throttle as possible. Be sure to adapt
your speed and driving to the prevail-
ing road conditions.
NOTE:
 The “ESC Activation/
Malfunction Indicator Light”
and the “ESC OFF Indicator
Light” come on momentarily
each time the ignition switch is
turned ON.
 Each time the ignition is turned ON, the ESC system will be ON
even if it was turned off previ-
ously.
 The ESC system will make buzz- ing or clicking sounds when it is
active. This is normal; the
sounds will stop when ESC be-
comes inactive following the
maneuver that caused the ESC
activation.
The “ESC OFF Indicator
Light” indicates the Elec-
tronic Stability Control
(ESC) is off.
SYNCHRONIZING ESC
If the power supply is inter-
rupted (battery disconnected
or discharged), the “ESC
Activation/Malfunction Indi-
cator Light” may illuminate with the
213

Electronic Speed Control (for
versions/markets, where
provided)
Do not use in hilly terrain or withheavy loads.
When using the speed control, if you experience speed drops greater
than 16 km/h, disengage until you
can get back to cruising speed.
Use speed control in flat terrain and with light loads to maximize
fuel efficiency.
AutoStick® (for versions/markets,
where provided)
By using the AutoStick® mode and selecting a specific gear range, fr e-
quent shifting can be avoided. The
highest gear range should be se-
lected that allows for adequate per-
formance. For example, choose “4”
if the desired speed can be main-
tained. Choose “3” or “2” if needed
to maintain the desired speed.
Extended driving at high RPM should be avoided to prevent excess heat generation. A reduction in
ve-
hicle speed may be required to
avoid extended driving at high
RPM. Return to a higher gear range
or vehicle speed when road condi-
tions and RPM level allows.
Cooling System
To reduce potential for engine and
transmission overheating, take the
following actions:
City Driving
When stopped for short periods of
time, shift the transmission into NEU-
TRAL and increase engine idle speed.
Highway Driving
Reduce speed.
Air Conditioning
Turn off temporarily.
TRAILER HITCH
ATTACHING POINTS
Your vehicle will require extra equip-
ment to tow a trailer safely and effi-
ciently. The trailer tow hitch must be
attached to your vehicle using the
provided attaching points on the ve- hicle's frame. Refer to the following
chart to determine the accurate
at-
taching points. Other equipment,
such as trailer sway controls and
braking equipment, trailer equalizing
(leveling) equipment and low profile
mirrors, may also be required or
strongly recommended.
Trailer Tow Hitch Attaching
Points And Overhang Dimen- sions
A 638.9 mm
B 746.1 mm
C 831.1 mm
D (maximum
overhang) 1161.5 mm
E 535.3 mm
F 520.3 mm
236

TIREFIT KIT (for
versions/markets, where
provided)
Small punctures up to
14” (6 mm) in
the tire tread can be sealed with
TIREFIT. Foreign objects (e.g.,
screws or nails) should not be re-
moved from the tire. TIREFIT can be
used in outside temperatures down to
approximately ­20°C.
This kit will provide a temporary tire
seal, allowing you to drive your ve-
hicle up to 160 km with a maximum
speed of 88 km/hr.
TIREFIT STORAGE
The TIREFIT kit is located in the
trunk. TIREFIT KIT
COMPONENTS AND
OPERATION
1. Sealant Bottle
2. Deflation Button
3. Pressure Gauge
4. Power Button
5. Mode Select Knob
6. Sealant Hose (Clear)
7. Air Pump Hose (Black)
8. Power Plug
Using The Mode Select Knob And
Hoses
Your TIREFIT kit is equipped with
the following symbols to indicate the
air or sealant mode.Selecting Air Mode
Turn the Mode Select Knob
(5) to this position for air
pump operation only. Use
the Black Air Pump Hose
(7) when selecting this mode.
Selecting Sealant Mode
Turn the Mode Se-
lect Knob (5) to this
position to inject
the TIREFIT Seal-
ant and to inflate
the tire. Use the
Sealant Hose (clear
hose) (6) when selecting this mode.
Using The Power Button
Push and release the Power
Button (4) once to turn On
the TIREFIT kit. Push and
release the Power Button (4)
again to turn Off the TIREFIT kit.
Using The Deflation ButtonPress the Deflation Button
(2) to reduce the air pres-
sure in the tire if it becomes
over-inflated.
TIREFIT Location
241

flow from the Sealant Bottle (1)
through the Sealant Hose (6) and
into the tire.
NOTE:
Sealant may leak out through the
puncture in the tire.
If the sealant (white fluid) does not
flow within 0 – 10 seconds through
the Sealant Hose (6):
1. Press the Power Button (4) to turn
Off the TIREFIT kit. Disconnect the
Sealant Hose (6) from the valve stem.
Make sure the valve stem is free of
debris. Reconnect the Sealant Hose
(6) to the valve stem. Check that the
Mode Select Knob (5) is in the Sealant
Mode position and not Air Mode.
Press the Power Button (4) to turn On
the TIREFIT kit.
2. Connect the Power Plug (8) to a
different 12 Volt power outlet in your
vehicle or another vehicle, if avail-
able. Make sure the engine is running
before turning ON the TIREFIT kit.
3. The Sealant Bottle (1) may be
empty due to previous use. Call for
assistance. NOTE:
If the Mode Select Knob (5) is on
Air Mode and the pump is operat-
ing, air will dispense from the Air
Pump Hose (7) only, not the Seal-
ant Hose (6).
If the sealant (white fluid) does
flow
through the Sealant Hose (6):
1. Continue to operate the pump un-
til sealant is no longer flowing
through hose (typically takes 30 -
70 seconds). As the sealant flows
through the Sealant Hose (6), the
Pressure Gauge (3) can read as high
as 5 Bar. The Pressure Gauge (3) will
decrease quickly from approximately
70 psi (5 Bar) to the actual tire pres-
sure when the Sealant Bottle (1) is
empty.
2. The pump will start to inject air
into the tire immediately after the
Sealant Bottle (1) is empty. Continue
to operate the pump and inflate the
tire to the pressure indicated on the
tire pressure label on the driver-side
latch pillar (recommended pressure).
Check the tire pressure by looking at
the Pressure Gauge (3). If the tire does not inflate to at least
1.8 Bar pressure within 15 min-
utes:
 The tire is too badly damaged. Do
not attempt to drive the vehicle fur-
ther. Call for assistance.
NOTE:
If the tire becomes over-inflated,
press the Deflation Button to re-
duce the tire pressure to the rec-
ommended inflation pressure be-
fore continuing.
If the tire inflates to the recom-
mended pressure or is at least 1.8
Bar pressure within 15 minutes:
1. Press the Power Button (4) to turn
off the TIREFIT kit.
2. Remove the Speed Limit sticker
from the top of the Sealant Bottle (1)
and place the sticker on the instru-
ment panel.
3. Immediately disconnect the Seal-
ant Hose (6) from the valve stem,
reinstall the cap on the fitting at the
end of the hose, and place the TIRE-
244

FIT kit in the vehicle storage location.
Quickly proceed to (D) “Drive Ve-
hicle”.CAUTION!
 The metal end fitting from PowerPlug (8) may get hot after use, so
it should be handled carefully.
 Failure to reinstall the cap on the
fitting at the end of the Sealant
Hose (6) can result in sealant con-
tacting your skin, clothing, and
the vehicle’s interior. It can also
result in sealant contacting inter-
nal TIREFIT kit components
which may cause permanent
damage to the kit.
(D) Drive Vehicle:
Immediately after injecting sealant
and inflating the tire, drive the vehicle
8 km or 10 minutes to ensure distri-
bution of the TIREFIT Sealant within
the tire. Do not exceed 88 km/h.
WARNING!
TIREFIT is not a permanent flat tire
repair. Have the tire inspected and
repaired or replaced after using
TIREFIT. Do not exceed 55 mph
(88 km/h) until the tire is repaired
or replaced. Failure to follow this
warning can result in injuries that
are serious or fatal to you, your pas-
sengers, and others around you.
(E) After Driving:
Pull over to a safe location. Refer to
“Whenever You Stop to Use TIRE-
FIT” before continuing.
1. Turn the Mode Select Knob (5) to
the Air Mode position.
2. Uncoil the power plug and insert
the plug into the vehicle's 12 Volt
power outlet.
3. Uncoil the Air Pump Hose (7)
(black in color) and screw the fitting
at the end of hose (7) onto the valve
stem.
4. Check the pressure in the tire by
reading the Pressure Gauge (3). If tire pressure is less than 1.3 Bar,
the tire is too badly damaged. Do not
attempt to drive the vehicle further.
Call for assistance.
If the tire pressure is 1.3 Bar or
higher:
1. Press the Power Button (4) to turn
on TIREFIT and inflate the tire to the
pressure indicated on the tire and
loading information label on the
driver
-side door opening.
NOTE:
If the tire becomes over-inflated,
press the Deflation Button to re-
duce the tire pressure to the rec-
ommended inflation pressure be-
fore continuing.
2. Disconnect the TIREFIT kit from
the valve stem, reinstall the cap on the
valve stem and unplug from 12 Volt
outlet.
3. Place the TIREFIT kit in its proper
storage area in the vehicle.
4. Have the tire inspected and re-
paired or replaced at the earliest op-
portunity at an authorized dealer or
tire service center.
245

Automatic Door . . . . . . . . . . 19
Child Protection . . . . . . . . . . 20
Door . . . . . . . . . . . . . . . . . . 18
Power Door . . . . . . . . . . . . . 19
Low Tire Pressure System . . . . 219
Lower Anchors and Tether for
CHildren (LATCH) . . . . . . . 46,47
Lubrication, Body . . . . . . . . . 262
Maintenance Free Battery . . . . 260
Maintenance Procedures . . . . . 257
Maintenance Schedule . . . 290,293
Maintenance, General . . . . . . . 257
Malfunction Indicator Light
(Check Engine) . . . . . . . . . . . 156
Manual Transmission . . . . . . . 271 Fluid Level Check . . . . . . . 271
Master Cylinder (Brakes) . . . . 269
Memory Feature (Memory
Seat) . . . . . . . . . . . . . . . . . . 101
Memory Seat . . . . . . . . . . . . . 101
Memory Seats and Radio . . . . 101
Methanol . . . . . . . . . . . . . . . 223
Methanol Fuel . . . . . . . . . . . . 223
Mini-Trip Computer . . . . . . . . 166
Mirrors . . . . . . . . . . . . . . . . . . 63
Automatic Dimming . . . . . . . 63
Electric Powered . . . . . . . . . 64
Electric Remote . . . . . . . . . . 64 Exterior Folding . . . . . . . . . . 63
Heated . . . . . . . . . . . . . . . . 65
Outside . . . . . . . . . . . . . . . . 63
Vanity . . . . . . . . . . . . . . . . . 65
Mode Fuel Saver . . . . . . . . . . . . . 165
Modifications/Alterations,
Vehicle . . . . . . . . . . . . . . . . . . . 7
Monitor, Tire Pressure
System . . . . . . . . . . . . . . . . . 219
Multi-Function Control
Lever . . . . . . . . . . . . . . . . . . 107
Navigation System
(Uconnect™ gps) . . . . . . 134,177
New Vehicle Break-In Period . . 50
Occupant Restraints . . . . 25,37,40
Occupant Restraints
(Sedan) . . . . . . . . . . . . . 35,37,39
Octane Rating, Gasoline
(Fuel) . . . . . . . . . . . . . . 223,284
Odometer . . . . . . . . . . . . . . . 154
Oil Change Indicator . . . . 154,164
Oil Change Indicator,
Reset . . . . . . . . . . . . . . . 154,164
Oil, Engine . . . . . . . . . . . 258,284 Capacity . . . . . . . . . . . . . . 283
Change Interval . . . . . . 164,258 Diesel . . . . . . . . . . . . . . . . 259
Dipstick . . . . . . . . . . . . . . . 258
Filter . . . . . . . . . . . . . 259,284
Materials Added to . . . . . . . 259
Recommendation . . 258,259,283
Synthetic . . . . . . . . . . . . . . 259
Viscosity . . . . . . . . . . . . . . 283
Onboard Diagnostic System . . 257
Operating Precautions . . . . . . 257
Operator Manual (Owner's
Manual) . . . . . . . . . . . . . . . . . . 5
Outside Rearview Mirrors . . . . . 63
Overdrive . . . . . . . . . . . . . . . 202
Overdrive OFF Switch . . . . . . 202
Overhead Console . . . . . . . . . 135
Overheating, Engine . . . . 159,240
Owner's Manual (Operator
Manual) . . . . . . . . . . . . . . . . . . 5
Paint Care . . . . . . . . . . . . . . . 271
Park Sense System, Rear . . . . 129
Parking Brake . . . . . . . . . . . . 206
Passing Light . . . . . . . . . . . . 108
Pedals, Adjustable . . . . . . . . . 114
Pets . . . . . . . . . . . . . . . . . . . . 50
Power
Deck Lid Release . . . . . . . . . 24
Distribution Center
(Fuses) . . . . . . . . . . . . 274,276
303