2012 Lancia Thema wiper fluid

WINDSHIELD WIPERS
AND WASHERS
The multifunction lever operates the
windshield wipers and washer when
the ignition is placed in the ON/RUN
or ACC position. The multifunction
lever is located on the left side of the
steering column.
Rotate the end of the multifunction
lever to the first detent, past the inter-
mittent settings for low-speed wiper
operation, or to the second detent past
the intermittent settings for high-
speed wiper operation.
CAUTION!
 Turn the windshield wipers offwhen driving through an auto-
matic car wash. Damage to the
windshield wipers may result if
the wiper control is left in any
position other than off.
 In cold weather, always turn off
the wiper switch and allow the
wipers to return to the “Park” po-
sition before turning off the en-
gine. If the wiper switch is left on
and the wipers freeze to the wind-
shield, damage to the wiper motor
may occur when the vehicle is re-
started.
 Always remove any buildup of
snow that prevents the windshield
wiper blades from returning to the
off position. If the windshield
wiper control is turned off and the
blades cannot return to the off
position, damage to the wiper mo-
tor may occur.
INTERMITTENT WIPER
SYSTEM
Use the intermittent wiper when
weather conditions make a single wiping cycle with a variable pause
between cycles desirable. Rotate the
end of the multifunction lever to the
first detent position, and then turn the
end of the lever to select the desired
delay interval. There are four delay
settings, which allow you to regulate
the wipe interval from a minimum of
one cycle every second to a maximum
of approximately 18 seconds between
cycles. The delay intervals will double
in duration when the vehicle speed is
16 km/h or less.
MIST FEATURE
Rotate the end of the lever downward
to the Mist position to activate a single
wipe cycle to clear off road mist or
spray from a passing vehicle. The
wipers will continue to operate until
you release the multifunction lever.
NOTE:
The mist feature does not activate
the washer pump; therefore, no
washer fluid will be sprayed on the
windshield. The wash function
must be used in order to spray the
windshield with washer fluid.
Windshield Wiper/Washer Control
110

NOTE:
 The Rain Sensing feature willnot operate when the wiper
speed is in the low or high posi-
tion.
 The Rain Sensing feature may not function properly when ice
or dried salt water is present on
the windshield.
 Use of Rain­X® or products containing wax or silicone may
reduce rain sensor performance.
The Rain Sensing system has protec-
tive features for the wiper blades and
arms. It will not operate under the
following conditions:
 Low Temperature Wipe Inhibit
— The Rain Sensing feature will
not operate when the ignition is
placed in the RUN position, the ve-
hicle is stationary and the outside
temperature is below 0°C, unless
the wiper control on the multifunc-
tion lever is moved, the vehicle
speed becomes greater than 0 km/h
or the outside temperature rises
above freezing. 
Neutral Wipe Inhibit — The Rain
Sensing feature will not operate
when the ignition is placed in the
RUN position, the transmission
shift lever is in the NEUTRAL po-
sition and the vehicle speed is less
than 8 km/h, unless the wiper con-
trol on the multifunction lever is
moved or the shift lever is moved
out of the NEUTRAL position.
HEADLIGHT WASHERS
(for versions/markets,
where provided)
The multifunction lever operates the
headlight washers when the ignition
switch is in the ON position and the
headlights are turned on. The multi-
function lever is located on the left
side of the steering column.
To use the headlight washers, push
the multifunction lever inward (to-
ward the steering column) to the sec-
ond detent and release it. The head-
light washers will spray a timed high-
pressure spray of washer fluid onto
each headlight lens. In addition, the windshield washers will spray the
windshield and the windshield wipers
will cycle.
NOTE:
After turning the ignition switch
and headlights ON, the headlight
washers will operate on the first
spray of the windshield washer
and then every eleventh spray after
that.
TILT/TELESCOPING
STEERING COLUMN
This feature allows you to tilt the
steering column upward or down-
ward. It also allows you to lengthen or
shorten the steering column. The tilt/
telescoping control handle is located
below the steering wheel at the end of
the steering column.
Tilt/Telescoping Control Handle
112

7
MAINTAINING YOUR VEHICLE
 ENGINE COMPARTMENT — 3.6L . . . . . . . . . . . 255
 ENGINE COMPARTMENT — 3.0L DIESEL . . . . 256
 ONBOARD DIAGNOSTIC SYSTEM — OBD II . . . 257
 REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . 257
 MAINTENANCE PROCEDURES . . . . . . . . . . . . . 257  ENGINE OIL – GASOLINE ENGINE . . . . . . . . 258
 ENGINE OIL – DIESEL ENGINE . . . . . . . . . . 259
 SYNTHETIC ENGINE OILS . . . . . . . . . . . . . . 259
 MATERIALS ADDED TO ENGINE OILS . . . . . 259
 DISPOSING OF USED ENGINE OIL ANDFILTERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 259
 ENGINE OIL FILTER . . . . . . . . . . . . . . . . . . . 259
 ENGINE AIR CLEANER FILTER . . . . . . . . . . 259
 MAINTENANCE-FREE BATTERY . . . . . . . . . 260
 AIR CONDITIONER MAINTENANCE . . . . . . . 261
 A/C AIR FILTER . . . . . . . . . . . . . . . . . . . . . . 261
 BODY LUBRICATION . . . . . . . . . . . . . . . . . . . 262
 WINDSHIELD WIPER BLADES . . . . . . . . . . . 263
 ADDING WASHER FLUID . . . . . . . . . . . . . . . 263
 INTERVENTION REGENERATION STRATEGY – 3.0L DIESEL ENGINE . . . . . . . 264
253

The filter is located in the fresh air
inlet under the hood, behind a remov-
able panel in the cowl on the passen-
ger side of the vehicle, next to the
windshield wipers. When installing a
new filter, ensure its proper orienta-
tion.
1. Remove the access door in the cowl
screen by pressing the retaining clips.
2. Unsnap both ends and lift the filter
access cover.3. Remove the used filter.
4. Install the new filter with arrows
pointing in the direction of airflow,
which is toward the rear of the vehicle
(text and arrows on the filter will in-
dicate this).
5. Close the filter access cover.
Refer to the “Maintenance Schedule”
for the proper maintenance intervals.
BODY LUBRICATION
Locks and all body pivot points, in-
cluding such items as seat tracks, door
hinge pivot points and rollers, liftgate,
tailgate, sliding doors and hood
hinges, should be lubricated periodi-
cally with a lithium based grease to
assure quiet, easy operation and to
protect against rust and wear. Prior to
the application of any lubricant, theparts concerned should be wiped
clean to remove dust and grit; after
lubricating excess oil and grease
should be removed. Particular atten-
tion should also be given to hood
latching components to ensure proper
function. When performing other un-
derhood services, the hood latch, re-
lease mechanism and safety catch
should be cleaned and lubricated.
The external lock cylinders should be
lubricated twice a year, preferably in
the Fall and Spring. Apply a small
amount of a high quality lubricant
directly into the lock cylinder.
CAUTION!
Car maintenance should be done at
a LANCIA Dealership. For routine
and minor maintenance operations
you wish to carry out yourself, we do
recommend you have the proper
equipment, genuine LANCIA spare
parts and the necessary fluids; do
not however carry out these opera-
tions if you have no experience.
Access Door
Filter Access Cover
A/C Air Filter
262

WINDSHIELD WIPER
BLADES
Clean the rubber edges of the wiper
blades and the windshield periodi-
cally with a sponge or soft cloth and a
mild nonabrasive cleaner. This will
remove accumulations of salt or road
film.
Operation of the wipers on dry glass
for long periods may cause deteriora-
tion of the wiper blades. Always use
washer fluid when using the wipers to
remove salt or dirt from a dry wind-
shield.
Avoid using the wiper blades to re-
move frost or ice from the windshield.
Keep the blade rubber out of contact
with petroleum products such as en-
gine oil, gasoline, etc.
NOTE:
Life expectancy of wiper blades
varies depending on geographical
area and frequency of use. Poor
performance of blades may be
present with chattering, marks,
water lines or wet spots. If any ofthese conditions are present, clean
the wiper blades or replace as nec-
essary.
ADDING WASHER FLUID
The windshield washer and the head-
light washer (for versions/markets,
where provided) share the same fluid
reservoir. The fluid reservoir is lo-
cated in the front of the engine com-
partment. Be sure to check the fluid
level in the reservoir at regular inter-
vals. Fill the reservoir with windshield
washer solvent (not radiator anti-
freeze) and operate the system for a
few seconds to flush out the residual
water.
When refilling the washer fluid reser-
voir, apply some washer fluid to a
cloth or towel and wipe the wiper
blades clean. This will help blade per-
formance.
To prevent freeze-up of your wind-
shield washer system in cold weather,
select a solution or mixture that meets
or exceeds the temperature range of
your climate. This rating information
can be found on most washer fluid
containers.The fluid reservoir will hold nearly
4 Liters of washer fluid when the mes-
sage “Low Washer Fluid” appears in
the Electronic Vehicle Information
Center (EVIC) (for versions/markets,
where provided).
WARNING!
Commercially available windshield
washer solvents are flammable.
They could ignite and burn you.
Care must be exercised when filling
or working around the washer solu-
tion.CAUTION!
Car maintenance should be done at
a LANCIA Dealership. For routine
and minor maintenance operations
you wish to carry out yourself, we do
recommend you have the proper
equipment, genuine LANCIA spare
parts and the necessary fluids; do
not however carry out these opera-
tions if you have no experience.
263

Thousands Of Kilometers24 48 72 96 120 144 168 192
Months 12 24 36 48 60 72 84 96
Check tire condition/wear and adjust pressure, if neces-
sary.        
Check operation of lighting system (headlamps, direction
indicators, hazard warning lights, luggage compartment,
passenger compartment, glove compartment, instrument
panel warning lights, etc.).        
Check operation of windscreen washer system and adjust
jets if necessary.        
Check windshield/rear window wiper blade position/
wear.        
Check cleanliness of hood and tailgate locks and cleanli-
ness and lubrication of linkages.        
Visually inspect condition of: exterior bodywork, under-
body protection, pipes and hoses (exhaust - fuel system -
brakes), rubber elements (boots, sleeves, bushes, etc.).        
Check conditions and wear of front disc brake pads.        
Check conditions and wear of rear disc brake pads.        
Check and, if necessary, top up fluid levels (brakes, wind-
shield washer, battery, engine coolant, etc.).        
Visually inspect the condition of accessory drive belt/s. 
Adjust parking brake shoes as necessary. 
Check exhaust gas emissions.        
Check engine management system operation (via diag-
nostic socket).        
Change the automatic transmission fluid and filter (*) 
291

Thousands Of Kilometers24 48 72 96 120 144 168 192
Months 12 24 36 48 60 72 84 96
Replace spark plugs. 
Replace air filter cartridge.    
Change engine oil and replace oil filter. Every 12.000 km or 12 months whichever comes first
Change brake fluid (or every 24 months). 
Replace pollen filter.        
(*) Change the automatic transmis-
sion fluid and filter(s) at 96 000 km
or 48 months if using your vehicle for
any of the following: city driving,
short (less than 7-8 km) and repeated
journeys, or frequent trailer or cara-
van towing.
Periodic Checks
Every 1 000 km or before long jour-
neys, check and, if necessary, restore:
 engine coolant;
 brake fluid;
 windshield washer fluid level;
 tire inflation pressure and condi- tion;
 operation of lighting system (head- lights, direction indicators, hazard
warning lights, etc.);  operation of windshield washer/
wiper system and positioning/wear
of windshield/rear window wiper
blades.
Every 3 000 km, check and top up, if
required, the engine oil level.
Heavy-Duty Use Of The Car
If the car is used mainly under one of
the following conditions:
 towing a trailer or caravan;
 dusty roads;
 short, repeated journeys (less than 7-8 km) at sub-zero outside tem-
peratures;
 engine often idling or driving long distances at low speeds or long pe-
riods of idleness. You should perform the following in-
spections more frequently than shown
on the Scheduled Servicing Plan:
 check front disc brake pad condi-
tions and wear;
 check cleanliness of hood and trunk locks, cleanliness and lubrication of
linkage;
 visually inspect conditions of: en- gine, transmission, pipes and hoses
(exhaust - fuel system - brakes) and
rubber elements (boots - sleeves -
bushes - etc.);
 check battery charge and battery fluid level (electrolyte);
 visually inspect condition of the ac- cessory drive belts;
 check and, if necessary, change en- gine oil and replace oil filter;
292

Thousands Of Kilometers20 40 60 80 100 120 140 160
Months 12 24 36 48 60 72 84 96
Check operation of windscreen washer system and adjust
jets if necessary.        
Check windshield/rear window wiper blade position/
wear.        
Check cleanliness of hood and tailgate locks and cleanli-
ness and lubrication of linkages.        
Visually inspect condition of: exterior bodywork, under-
body protection, pipes and hoses (exhaust - fuel system -
brakes), rubber elements (boots, sleeves, bushes, etc.).        
Check conditions and wear of front disc brake pads.        
Check conditions and wear of rear disc brake pads.        
Check and, if necessary, top up fluid levels (brakes,
windshield washer, battery, engine coolant, etc.).        
Visually inspect the condition of accessory drive belt/s. 
Adjust parking brake shoes as necessary. 
Check exhaust gas emissions.        
Check engine management system operation (via diag-
nostic socket).        
Change the automatic transmission fluid and filter (*). 
Replace fuel filter. 
Replace accessory drive belt/s. 
Replace air filter cartridge. 
Change engine oil and replace oil filter (**).
Change brake fluid (or every 24 months). 
Replace pollen filter.        
294