2012 DODGE DURANGO Owners Manual

Jacking Instructions
WARNING!
Carefully follow these tire changing warnings to
help prevent personal injury or damage to your
vehicle:
•Always park on a firm, level surface as far from
the edge of the roadway as possible before raising
the vehicle.
•Turn on the Hazard Warning flasher.
•Block the wheel diagonally opposite the wheel to
be raised.
•Set the parking brake firmly and set the automatic
transmission in PARK.
•Never start or run the engine with the vehicle on a
jack.(Continued)
WARNING! (Continued)
•Do not let anyone sit in the vehicle when it is on a
jack.
•Do not get under the vehicle when it is on a jack.
•Only use the jack in the positions indicated and
for lifting this vehicle during a tire change.
•If working on or near a roadway, be extremely
careful of motor traffic.
•To assure that spare tires, flat or inflated, are
securely stowed, spares must be stowed with the
valve stem facing the ground.
Jack Warning Label
6
WHAT TO DO IN EMERGENCIES 559

CAUTION!
Do not attempt to raise the vehicle by jacking on
locations other than those indicated in the Jacking
Instructions for this vehicle.
1. Loosen (but do not remove) the wheel lug nuts by
turning them to the left, one turn, while the wheel is still
on the ground.
2. Assemble the jack and jacking tools.
3. For the front axle, place the jack on the body flange
just behind the front tire as indicated by the triangular lift
point symbol on the sill molding.Do not raise the
vehicle until you are sure the jack is fully engaged.
Jack and Tool Assembly
560 WHAT TO DO IN EMERGENCIES

Lift Point Symbol On Sill MoldingFront Jacking Location6
WHAT TO DO IN EMERGENCIES 561

4. For a rear tire, place the jack in the slot on the rear
tie-down bracket, just forward of the rear tire (as indi-
cated by the triangular lift point symbol on the sill
molding).Do not raise the vehicle until you are sure the
jack is fully engaged.
5. Raise the vehicle by turning the jack screw clockwise.
Raise the vehicle just enough to remove the flat tire.
Lift Point Symbol On Sill Molding
Rear Jacking Location
562 WHAT TO DO IN EMERGENCIES

WARNING!
Raising the vehicle higher than necessary can make
the vehicle less stable. It could slip off the jack and
hurt someone near it. Raise the vehicle only enough
to remove the tire.
6. Remove the lug nuts and wheel.
7. Install the spare wheel/tire on the vehicle and install
the lug nuts with the cone-shaped end toward the wheel.
Lightly tighten the nuts.
CAUTION!
Be sure to mount the spare tire with the valve stem
facing outward. The vehicle could be damaged if the
spare tire is mounted incorrectly.WARNING!
To avoid the risk of forcing the vehicle off the jack,
do not fully tighten the wheel nuts until the vehicle
has been lowered. Failure to follow this warning may
result in personal injury.
Mounting Spare Tire6
WHAT TO DO IN EMERGENCIES 563

8. Lower the vehicle by turning the jack screw counter-
clockwise, and remove the jack and wheel blocks.
9. Finish tightening the lug nuts. Push down on the
wrench while at the end of the handle for increased
leverage. Tighten the lug nuts in a star pattern until each
nut has been tightened twice. The correct wheel nut
tightness is 110 ft lbs (150 N·m). If in doubt about the
correct tightness, have them checked with a torque
wrench by your authorized dealer or at a service station.
10. Remove the small center cap and position the alumi-
num road wheel behind rear bumper with the “beauty
side” facing rearward.11. Insert the two long tubes on the plastic protective
plate in the lug holes of the road wheel. Push the end of
the winch’s cable, spring, steel sleeve and stamped cone
shape wheel plate though the road wheel and protective
plate.
“Beauty Side”
564 WHAT TO DO IN EMERGENCIES

12. Slide the road wheel on the ground using the protec-
tive plate until it is directly under the winch and between
the rear bumper and exhaust system heat shields. Raise
the tire by turn the lug wrench on the winch extension
clockwise until it clicks/ratchets three times to make sure
the cable is tight.NOTE:
Double check to ensure the tire is snug against
the underbody of the vehicle. Damage to the winch cable
may result if the vehicle is driven with the tire loose.
Installing WinchRoad Wheel Installed In Spare Location6
WHAT TO DO IN EMERGENCIES 565

WARNING!
Do not use power tools to winch the tire up or down.
Impact-type tools may damage the winch mecha-
nism.
13. Lower the jack to the fully closed position. Return the
tools to the proper positions in the tool bag. Fold the flap
on the tool bag under the tools and roll the tools in the
bag underneath the others. Use the Velcro straps to
secure the tool bag to the jack with the lug wrench on the
forward side of the jack. Expand the jack on the bracket
by turning the thumb screw clockwise until it is tight to
prevent rattles.
14. Reinstall the plastic plug into the floor of the cargo
area. Roll up and store the Jack, Tool Kit and Tire
Changing Instructions. Reinstall the cover for the jack in
the rear storage bin. 15. Have the aluminum road wheel and tire repaired as
soon as possible and properly secure the spare tire, jack
and tool kit.
WARNING!
A loose tire or jack, thrown forward in a collision or
hard stop could endanger the occupants of the ve-
hicle. Always stow the jack parts and the spare tire in
the places provided.
Road Tire Installation
1. Mount the road tire on the axle.
2. Install the remaining lug nuts with the cone shaped
end of the nut toward the wheel. Lightly tighten the lug
nuts.
566 WHAT TO DO IN EMERGENCIES