2011 RENAULT SCENIC Df249

13B-37V9 MR-372-J84-13B450$090.mif
DIESEL INJECTION
Fault finding – Fault summary table13B
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58
Management of instrument panel warning lights according to the faults notified.
*temp: temperatureFaultDTC code in
hexadecimalLevel 1 fault
warning light
(orange
SERVICE
warning light)Level 2 fault
warning light
(red STOP
warning light)No fault
warning
light litOBD
warning
light lit
DF200 Atmospheric pressure
sensor2226 1.DEF/2.DEF - -1.DEF/
2.DEF
DF209 EGR valve position
sensor circuit409 - - CC.1/CO.0CC.1/
CO.0
DF221 Clutch contact signal 830 - - 1.DEF -
DF226 Damper valve circuit 120CO/CC.0/CC.1/
CC/1.DEF/
2.DEF-3.DEF-
DF228 Brake signal 571 - -1.DEF/
2.DEF-
DF232 Coolant pressure
sensor circuit530 - - CC.0/CO.1CC.0/
CO.1
DF249 Injector control 62B - 1.DEF - -
DF272 EGR valve control
circuit487 - -CO/CC.1/
CC.0/CCCO/CC.1/
CC.0/CC
DF276 Injector code
programming611 1.DEF/2.DEF - - -
DF293 Water in diesel fuel
detector2269 - - 1.DEF -
DF308 Clogged particle filter 242F X - - -
DF309 Particle filter
downstream temp* sensor242A - - CO.1/CC.0 -
DF310 Particle filter upstream
temp* sensor2031 CO.1/CC.0 - -CO.1/
CC.0
DF311 Number of failed
regenerations exceeded1435 X - - -

13B-99V9 MR-372-J84-13B450$102.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF059
PRESENT
OR
STOREDCOMBUSTION MISFIRES ON CYLINDER 1
1.DEF: Above maximum threshold
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after:
– engine speed is between idling speed and 1050 rpm PR055 Engine speed,
–PR064 Coolant temperature ≥ 50°C.
Priorities when dealing with a number of faults:
Apply the interpretation of faults DF026 CYLINDER 1 INJECTOR CONTROL
CIRCUIT and DF249 Injector control first if they are present or stored.
Special notes:
Check that the stored injector codes are consistent with those engraved on each
injector. If not, run command SC002 Enter injector codes and follow the procedure,
After an injector has been replaced, run command SC002 Enter injector codes and
command SC036 Reintialise programming and follow the procedure.
IMPORTANT
Possible absence of combustion on one cylinder even though the injector is properly
fed.
Cylinder no. 1 is located at the timing end.
Do not disconnect the injectors when the engine is running.
When removing or refitting an injector, follow the cleanliness and safety instructions
(see MR 364 (Mégane) or 370 (Scénic), Mechanical, 13B, Diesel injection, Diesel
injector: Removal - Refitting).
EDC16C36_V44_DF059/EDC16C36_V4C_DF059/EDC16C36_V48_DF059/EDC16C36_V50_DF059/EDC16C36_V54_DF059/
EDC16C36_V58_DF059
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-101V9 MR-372-J84-13B450$102.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF060
PRESENT
OR
STOREDMISFIRING ON CYLINDER 2
1.DEF: Above max threshold
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after:
– engine speed is between idling speed and 1050 rpm PR055 Engine speed,
–PR064 Coolant temperature ≥ 50°C.
Priorities when dealing with a number of faults:
Apply the interpretation of faults DF027 CYLINDER 2 INJECTOR CONTROL
CIRCUIT and DF249 Injector control first if they are present or stored.
Special notes:
Check that the stored injector codes are consistent with those engraved on each
injector. If not, run command SC002 Enter injector codes and follow the procedure.
After an injector has been replaced, run command SC002 Enter injector codes and
command SC036 Reintialise programming and follow the procedure.
IMPORTANT
Possible absence of combustion on one cylinder even though the injector is properly
fed.
Cylinder no. 1 is located at the timing end.
Do not disconnect the injectors when the engine is running.
When removing or refitting an injector, follow the cleanliness and safety instructions
(see MR 364 (Mégane) or 370 (Scénic), Mechanical, 13B, Diesel injection, Diesel
injector: Removal - Refitting).
EDC16C36_V44_DF060/EDC16C36_V4C_DF060/EDC16C36_V48_DF060/EDC16C36_V50_DF060/EDC16C36_V54_DF060/
EDC16C36_V58_DF060
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-103V9 MR-372-J84-13B450$102.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF061
PRESENT
OR
STOREDMISFIRING ON CYLINDER 3
1.DEF: Above max threshold
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after:
– engine speed is between idling speed and 1050 rpm PR055 Engine speed,
–PR064 Coolant temperature ≥ 50°C.
Priorities when dealing with a number of faults:
Apply the interpretation of faults DF028 Cylinder 3 injector control circuit and DF249
Injector control first if they are present or stored.
Special notes:
Check that the stored injector codes are consistent with those engraved on each
injector. If not, run command SC002 Enter injector codes and follow the procedure.
After replacing an injector, run commands SC002 Enter injector codes and SC036
Reinitialise programming, follow the procedures.
IMPORTANT
Possible absence of combustion on one cylinder even though the injector is properly
fed.
Cylinder no. 1 is located at the timing end.
Do not disconnect the injectors when the engine is running.
When removing or refitting an injector, follow the cleanliness and safety instructions
(see MR 364 (Mégane) or 370 (Scénic), Mechanical, 13B, Diesel injection, Diesel
injector: Removal - Refitting).
EDC16C36_V44_DF061/EDC16C36_V4C_DF061/EDC16C36_V48_DF061/EDC16C36_V50_DF061/EDC16C36_V54_DF061/
EDC16C36_V58_DF061
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-105V9 MR-372-J84-13B450$102.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF062
PRESENT
OR
STOREDMISFIRING ON CYLINDER 4
1.DEF: Above max threshold
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after:
– engine speed is between idling speed and 1050 rpm, PR055 Engine speed
–PR064 Coolant temperature ≥ 50°C.
Priorities when dealing with a number of faults:
Apply the interpretation of faults DF029 CYLINDER 4 INJECTOR CONTROL
CIRCUIT and DF249 Injector control first if they are present or stored.
Special notes:
Check that the stored injector codes are consistent with those engraved on each
injector. If not, run command SC002 Enter injector codes and follow the procedure.
After replacing an injector, run commands SC002 Enter injector codes and SC036
Reinitialise programming, follow the procedures.
IMPORTANT
Possible absence of combustion on one cylinder even though the injector is properly
fed.
Cylinder no. 1 is located at the timing end.
Do not disconnect the injectors when the engine is running.
When removing or refitting an injector, follow the cleanliness and safety instructions
(see MR 364 (Mégane) or 370 (Scénic), Mechanical, 13B, Diesel injection, Diesel
injector: Removal - Refitting).
EDC16C36_V44_DF062/EDC16C36_V4C_DF062/EDC16C36_V48_DF062/EDC16C36_V50_DF062/EDC16C36_V54_DF062/
EDC16C36_V58_DF062
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-107V9 MR-372-J84-13B450$102.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF065
PRESENT
OR
STOREDCOMBUSTION MISFIRES
1.DEF: Above max threshold
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after:
– engine speed is between idling speed and 1050 rpm PR055 Engine speed,
– a coolant temperature ≥ 50°C PR064 Coolant temperature.
Priorities when dealing with a number of faults:
DF249 Injector control, present or stored,
DF026 Injector 1 control circuit, present or stored,
DF027 Injector 2 control circuit, present or stored,
DF028 Injector 3 control circuit, present or stored,
DF029 Injector 4 control circuit, present or stored.
IMPORTANT
When removing or refitting an injector, observe the cleanliness and safety instructions
(see MR 364 (Mégane) or 370 (Scénic), Mechanical, 13B, Diesel injection, Diesel
injector: Removal - Refitting).
IMPORTANT
Possible absence of combustion on one cylinder even though the injector is properly
fed.
Do not disconnect the injectors when the engine is running.
EDC16C36_V44_DF065/EDC16C36_V4C_DF065/EDC16C36_V48_DF065/EDC16C36_V50_DF065/EDC16C36_V54_DF065/
EDC16C36_V58_DF065
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-151
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$103.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF249
PRESENT
OR
STOREDINJECTOR CONTROL
1.DEF: Internal electronic fault
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after:
– the ignition is switched on,
– the engine is started.
Priority when dealing with a number of faults:
Deal with faults DF046 Battery voltage, DF026 Injector cylinder 1 control circuit,
DF027 Injector cylinder 2 control circuit, DF028 Injector cylinder 3 control circuit
and DF029 Injector cylinder 4 control circuit first if they are present or stored.
Special notes:
In some cases if the fault is present, the level 2 warning light illuminates and the engine
stops.
Use bornier Elé.1681 for all operations on the engine management computer.
Use Wiring Diagram Technical Note, Mégane II ph2, Scénic II ph2.
EDC16C36_V44_DF249/EDC16C36_V4C_DF249/EDC16C36_V48_DF249/EDC16C36_V50_DF249/EDC16C36_V54_DF249/
EDC16C36_V58_DF249EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-152
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$103.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF249
CONTINUED
This fault appears when the computer detects a fault on the injector control section
Check the condition of the injector connectors (see Wiring Diagram Technical Note, Mégane II ph2, Scénic II
ph2, Component codes 193, 194, 195, 196).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Mégane II ph2, Scénic II ph2, component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the continuity and insulation of the following connections:
– Connection code 3KW between components 193 and 120.
– Connection code 3CR between components 193 and 120.
– Connection code 3KX between components 194 and 120.
– Connection code 3CS between components 194 and 120.
– Connection code 3KY between components 195 and 120.
– Connection code 3CT between components 195 and 120.
– Connection code 3KZ between components 196 and 120.
– Connection code 3CU between components 196 and 120.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58