2011 RENAULT SCENIC brake

13B-12V9 MR-372-J84-13B450$040.mif
13B
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58
High pressure pump:
The pump draws in fuel from the tank, which passes through a fuel filter and supplies the fuel injectors.
Rail pressure sensor:
This sensor is fitted to the rail and indicates the pressure inside the rail.
Rail pressure regulator:
This component regulates the high pressure of the fuel in the injection system.
Fuel temperature sensor:
This sensor measures the fuel return temperature from the pump and injector return.
Four injectors:
These injectors enable rapid, precise metering of the quantity of fuel injected, with excellent injection process repeat
action.
Vacuum pump:
The vacuum pump is driven by the camshaft. The pump provides the vacuum required to operate the following
components: control solenoid valve, brake servo.
Control solenoid valve:
The solenoid valve controls the vacuum pump and the turbocharger vane control diaphragm.
Turbocharger:
The turbocharger is used to supply the engine with more air.
Turbocharger pressure sensor:
This sensor indicates the pressure at the turbocharger air cooler outlet before the damper valve.
Air mass flow meter:
The flowmeter measures the amount of fresh air entering the engine.
EGR valve:
Exhaust gas recirculation considerably reduces the nitrogen oxide emissions (NOx).
EGR position sensor:
The sensor gives the position of the EGR solenoid valve.
Damper valve:
The damper valve is used:
– When the engine is switched off, to dampen the engine which helps stop the engine.
– When in the rest position; the valve is open by default.
DIESEL INJECTION
Fault finding – Role of components

13B-19V9 MR-372-J84-13B450$050.mif
DIESEL INJECTION
Fault finding – Features13B
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58
Cruise control/speed limiter management:
The vehicle cruise control function, when activated, allows you to keep the vehicle speed at a selected value
regardless of the driving conditions encountered.
Using the control buttons, the driver can increase or reduce the speed of the vehicle.
If the driver wishes to exceed the cruising speed, he may:
– press the accelerator pedal and exceed the cruising speed (the vehicle will return to the initial cruising speed once
the driver takes his foot off the pedal),
– press the system control buttons.
The cruise control function can be deselected either by:
– the system control buttons,
– deactivating the cruise control switch,
– when system events are detected, such as the brake pedal or clutch being pressed,
– when system errors are detected such as an inconsistent vehicle speed.
The cruise control function can also be temporarily disabled when the driver wants to increase speed by pressing
the accelerator pedal. The cruising speed is resumed when the driver releases the accelerator pedal.
The vehicle will then attempt to reach the cruising speed at a controlled acceleration rate.
It is possible to reactivate the vehicle speed control and resume the last cruising speed after deactivation (computer
feed not cut off).
When activated (using the selection switch) the vehicle speed limiter function limits the vehicle speed to a
preselected value. The driver controls the vehicle in the normal way using the accelerator pedal until the limit speed
is reached.
If an attempt is made to exceed this speed, the system ignores the pedal request and controls the vehicle speed in
the same way as the cruise control function, provided that the driver keeps the accelerator pedal depressed.
As with the cruise control function, the cruising speed can be altered using the control buttons by pressing briefly or
keeping the switch pressed.
For safety reasons, it is possible to exceed the limit speed by depressing the accelerator pedal and exceeding the
pedal position limit value. The vehicle speed is then totally controlled as a function of pedal position until the speed
falls back below the cruising speed when the speed limiter function will once again be reactivated.
If the driver wishes to exceed the cruising speed, he may:
– exceed the accelerator pedal's kickdown point,
– increase the limit speed by pressing or pressing and holding the limit speed switch.
The speed limiter function can be deselected either:
– the system control buttons,
– by switching off the speed limiter switch,
– when system events are detected, such as the brake pedal or clutch being pressed,
– when system errors are detected such as an inconsistent vehicle speed.

13B-37V9 MR-372-J84-13B450$090.mif
DIESEL INJECTION
Fault finding – Fault summary table13B
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58
Management of instrument panel warning lights according to the faults notified.
*temp: temperatureFaultDTC code in
hexadecimalLevel 1 fault
warning light
(orange
SERVICE
warning light)Level 2 fault
warning light
(red STOP
warning light)No fault
warning
light litOBD
warning
light lit
DF200 Atmospheric pressure
sensor2226 1.DEF/2.DEF - -1.DEF/
2.DEF
DF209 EGR valve position
sensor circuit409 - - CC.1/CO.0CC.1/
CO.0
DF221 Clutch contact signal 830 - - 1.DEF -
DF226 Damper valve circuit 120CO/CC.0/CC.1/
CC/1.DEF/
2.DEF-3.DEF-
DF228 Brake signal 571 - -1.DEF/
2.DEF-
DF232 Coolant pressure
sensor circuit530 - - CC.0/CO.1CC.0/
CO.1
DF249 Injector control 62B - 1.DEF - -
DF272 EGR valve control
circuit487 - -CO/CC.1/
CC.0/CCCO/CC.1/
CC.0/CC
DF276 Injector code
programming611 1.DEF/2.DEF - - -
DF293 Water in diesel fuel
detector2269 - - 1.DEF -
DF308 Clogged particle filter 242F X - - -
DF309 Particle filter
downstream temp* sensor242A - - CO.1/CC.0 -
DF310 Particle filter upstream
temp* sensor2031 CO.1/CC.0 - -CO.1/
CC.0
DF311 Number of failed
regenerations exceeded1435 X - - -

13B-125
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$103.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF165
PRESENT
OR
STOREDACCELERATOR PEDAL POSITION SENSOR CIRCUIT
1.DEF: No signal
2.DEF: Accelerator pedal sensor locked
3.DEF: Detection of accelerator pedal depressed at same time as brake pedal.
1.DEF
2.DEF
NOTESPriorities when dealing with a number of faults:
Deal with fault DF012 Sensor supply no. 2 voltage first, if
it is present or stored.
Conditions for applying the fault finding procedure to a
stored fault:
The fault occurs if the brake pedal and the accelerator pedal
are depressed simultaneously for more than 1 second.
Special notes:
If the fault is present,
–the level 2 warning light illuminates if 1.DEF or 2.DEF is
present,
– turbocharging and cruise control are not authorised,
– the engine speed is fixed at 1400 rpm,
– cruise control/speed limiter function unusable,
– limitation of the quantity of fuel injected.
Use bornier Elé.1681 for any operations on the computer
connectors.
Use Wiring Diagram Technical Note, Mégane II ph2,
Scénic II ph2.
EDC16C36_V44_DF165/EDC16C36_V4C_DF165/EDC16C36_V48_DF165/EDC16C36_V50_DF165/EDC16C36_V54_DF165/
EDC16C36_V58_DF165EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-127
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$103.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF165
CONTINUED 2
3.DEFNOTESPriorities when dealing with a number of faults:
Deal with fault DF012 Sensor feed voltage no. 2 first, if it is
present or stored.
Conditions for applying the fault finding procedure to a
stored fault:
The fault occurs if the brake pedal and the accelerator pedal
are depressed simultaneously for more than 30 seconds
without any movement.
Special notes:
Do not interpret the conditions under which the fault occurs.
Make sure that the accelerator pedal is not mechanically jammed (broken spring, floor carpet, etc.).
Check that the brake switch is correctly positioned in its housing.
If the fault is still present, deal with fault DF165 2.DEF.
If the fault is still present, contact the Techline.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-147
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$103.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF228
PRESENT
OR
STOREDBRAKE SIGNAL
1.DEF: Consistency with redundant brakes
2.DEF: Engine deceleration too high
1.DEF
2.DEF
NOTESConditions for applying the fault finding procedure to a
stored fault:
The fault is declared present after the brake pedal is
depressed.
Special notes:
If the fault is present, the cruise control/speed limiter is
switched off.
Use bornier Elé. 1681 for all operations on the engine
management computer connectors.
Use Wiring Diagram Technical Note, Mégane II ph2,
Scénic II ph2.
EDC16C36_V44_DF228/EDC16C36_V4C_DF228/EDC16C36_V48_DF228/EDC16C36_V50_DF228/EDC16C36_V54_DF228/
EDC16C36_V58_DF228EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-148
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$103.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF228
CONTINUED 1
From the List of Statuses menu, check ET012 and ET013 and check:
– brake pedal in rest position ET012 = "RELEASED" and ET013 = "RELEASED"
– brake pedal depressed ET012 = "DEPRESSED" and ET013 = "DEPRESSED"
Has ET013 been correctly recognised?
Has ET012 been correctly recognised?Clear the fault
End of fault finding
procedure
Check the connections of the brake pedal switch, the ABS computer, the electronic stability program
computer and the engine management computer.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring:
Precautions for repair), repair the wiring, otherwise replace it.
Check for + 12 V after ignition feed on the connections of the brake pedal switch connector and the
condition of the fuse.
– Connection code AP10 of component 160.
– Connection code SP13 of component 160.
Disconnect the ABS - ESP and check the continuity and insulation against + 12 V and against earth
of the following connection:
– Connection code 65A between components 160 and 1094.
Check that the brake pedal switch is working correctly:
in rest position: infinite resistance continuity between the following connections:
– Connection code 65A of component 160.
– Connection code AP10 of component 160.
depressed: continuity between the following connections:
– Connection code 65A of component 160.
– Connection code AP10 of component 160.
Replace the switch if necessary.
If the fault is still present, carry out fault finding on the anti-lock braking system - electronic stability
program; if no irregularity is detected, then carry out fault finding on the multiplex network.
YES
YES
NONO
A
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-149
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$103.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF228
CONTINUED 2
Check the brake pedal switch connections and the engine management computer connections.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
Check the condition and adjustment of the brake-pedal switch. Repair if necessary.
Check for + 12 V after ignition feed on the connections of the brake pedal switch connector and the condition of
the fuse.
– Connection code AP10 of component 160.
– Connection code SP13 of component 160.
Check the continuity and insulation against + 12 V and against earth of the following connection:
– Connection code 5A between components 160 and 120/645/119.
Check that the brake pedal switch is working correctly:
in rest position: infinite resistance continuity between the following connections:
– Connection code 5A of component 160.
– Connection code SP13 of component 160.
depressed: continuity between the following connections:
– Connection code 5A of component 160.
– Connection code SP13 of component 160.
Replace the switch if necessary.
A
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58