2011 RENAULT SCENIC engine

13B-214V9 MR-372-J84-13B450$131.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET038ENGINE
STATUS DEFINITION+ AFTER IGNITION: This status indicates that the engine is in + after ignition.
RUNNING: This status indicates that the engine is running.
STOPPED: This status indicates that the engine is stopped.
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
Conformity check with engine stopped and ignition on
STOPPEDStatus ET038 is Stopped if the engine ignition is on without the starter engaged.
Conformity check with engine running, engine coolant temperature > 80°C
RUNNINGThis status indicates that the engine is running.
In the event of a fault, switch off the ignition and wait for the diagnostic tool message
(maximum time 8 minutes) Communication lost with computer: EDC16C36,
check the tool connection and computer power supply, before switching the
ignition back on.
If the fault is still present, contact the Techline.
Status ET038 may also be in the STARTING or STALLED phase
UNDER
STARTERStatus ET038 is Starting when the engine is in starting phase.
STALLEDStatus ET038 is Stalled if the engine has stalled. The vehicle is still under +after
ignition feed.
EDC16C36_V44_ET038/EDC16C36_V4C_ET038/EDC16C36_V48_ET038/EDC16C36_V50_ET038/EDC16C36_V54_ET038/
EDC16C36_V58_ET038
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-215V9 MR-372-J84-13B450$131.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET039BRAKE PEDAL
STATUS DEFINITIONDEPRESSED: This status indicates that the brake pedal is in the depressed position.
RELEASED: This status indicates that the brake pedal is in the released position.
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature
> 80°C
DEPRESSEDStatus ET039 is RELEASED when there is no action on the brake pedal.
In the event of a fault, see the interpretation of statuses ET704 Brake switch no. 1
and ET705 Brake switch no. 2.
RELEASEDStatus ET039 is DEPRESSED when there is pressure on the brake pedal.
In the event of a fault, see the interpretation of statuses ET704 Brake switch no. 1
and ET705 Brake switch no. 2.
EDC16C36_V44_ET039/EDC16C36_V4C_ET039/EDC16C36_V48_ET039/EDC16C36_V50_ET039/EDC16C36_V54_ET039/
EDC16C36_V58_ET039
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-216V9 MR-372-J84-13B450$131.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET040CLUTCH PEDAL
STATUS DEFINITIONDEPRESSED: This status indicates that the clutch pedal is depressed.
RELEASED: This status indicates that the clutch pedal is released.
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature
> 80°C
DEPRESSEDStatus ET040 is DEPRESSED when there is no action on the clutch pedal.
In the event of a fault, see the interpretation of status ET405 Clutch pedal switch.
Non-conformity of the brake signals and or the clutch switch signals can cause the
engine to race during gear changes. In the event of a fault, contact the Techline.
RELEASEDWhen the vehicle ignition is switched on without depressing the clutch pedal, status
ET040 is RELEASED.
In the event of a fault, see the interpretation of status ET405 Clutch pedal switch.
Non-conformity of the brake signals and or the clutch switch signals can cause the
engine to race during gear changes. In the event of a fault, contact the Techline.
EDC16C36_V44_ET040/EDC16C36_V4C_ET040/EDC16C36_V48_ET040/EDC16C36_V50_ET040/EDC16C36_V54_ET040/
EDC16C36_V58_ET040
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-217V9 MR-372-J84-13B450$131.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET042CRUISE CONTROL/SPEED LIMITER
STATUS DEFINITIONNOT DETECTED: This status indicates that the cruise control or speed limiter function
is not present on the vehicle.
INACTIVE: This status indicates that the main On/Off switch of the cruise control/speed
limiter is in the rest (or neutral) position.
LIMITER: This status indicates that the driver has used the main switch to select the
speed limiter.
CRUISE CONTROL: This status indicates that the driver has used the main switch to
select the cruise control.
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
Use the Mégane II ph2, Scénic II ph2 Technical Note wiring diagram.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature
> 80°C
NOT DETECTEDThe cruise control or speed limiter function is not present on the vehicle.
INACTIVENo button has been pressed.
SPEED LIMITERThe speed limiter ON/OFF button has been pressed.
Lights the orange warning light on the instrument panel.
CRUISE
CONTROL
The cruise control ON/OFF button has been pressed.
Lights the green warning light on the instrument panel.
EDC16C36_V44_ET042/EDC16C36_V4C_ET042/EDC16C36_V48_ET042/EDC16C36_V50_ET042/EDC16C36_V54_ET042/
EDC16C36_V58_ET042
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-219V9 MR-372-J84-13B450$131.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET042
CONTINUED 2
INACTIVE
MEGANE II:
When the main switch is in rest position (or neutral), status ET042 is INACTIVE.
If CRUISE CONTROL or SPEED LIMITER appears despite the main switch being in
the rest (or neutral) position, carry out the following operations:
Check the connections of the cruise control/speed limiter main switch.
Check for +12 V after ignition on the switch connector.
– Connection code AP43 of component 1081.
Disconnect the main switch, and when it is in the rest position, check the insulation
between:
– Connection codes AP43 and 3FX, of component 1081.
– Connection codes AP43 and 3PD of component 1081.
Check the continuity between connections AP43 and 3PD of component 1081 in
the speed limiter position.
Check the continuity between connections AP43 and 3FX of component 1081 in
the cruise control position.
If these checks are not in order, replace the switch.
Check the continuity, insulation and the absence of interference resistance on
the following connections:
– Connection code 3FX,
– Connection code 3PD,
between components 1081 and 120.
Also check the engine management computer connectors.
If there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair) repair the wiring, otherwise replace it.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-220V9 MR-372-J84-13B450$131.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET042
CONTINUED 3
INACTIVE
SCENIC II:
When the main switch is in rest position (or neutral), status ET042 is INACTIVE.
If CRUISE CONTROL or SPEED LIMITER appears despite the main switch being in
the rest (or neutral) position, carry out the following operations:
Check the connections of the cruise control/speed limiter main switch.
Check for +12 V after ignition on the switch connector.
– Connection code AP43 of component 1546.
Disconnect the main switch, and when it is in the rest position, check the insulation
between:
– Connection codes AP43 and 3FX of component 1546.
– Connection codes AP43 and 3PD of component 1546.
Check the continuity between connections AP43 and 3PD of component 1546 in
the speed limiter position.
Check the continuity between connections AP43 and 3FX of component 1546 in
the cruise control position.
If these checks are not in order, replace the switch.
Check the continuity, insulation and the absence of interference resistance on
the following connections:
– Connection code 3FX,
– Connection code 3PD,
Between components 1546 and 120.
Also check the engine management computer connectors.
If there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair) repair the wiring, otherwise replace it.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-221V9 MR-372-J84-13B450$131.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET042
CONTINUED 4
SPEED LIMITER
MEGANE II:
When the driver presses the main speed limiter switch, status ET042 becomes
SPEED LIMITER.
If CRUISE CONTROL or INACTIVE appears although the switch was pressed in the
speed limiter position, carry out the following operations:
Check the connections of the cruise control/speed limiter main switch.
Check for +12 V after ignition on the switch connector.
– Connection code AP43 of component 1081.
Disconnect the main switch, and when it is in the rest position, check the insulation
between:
– Connection codes AP43 and 3FX of component 1081.
– Connection codes AP43 and 3PD of component 1081.
Check the continuity between connections AP43 and 3PD of component 1081 in
the speed limiter position.
Check the continuity between connections AP43 and 3FX of component 1081 in
the cruise control position.
If these checks are not in order, replace the switch.
Check the continuity, insulation and the absence of interference resistance on
the following connections:
– Connection code 3FX,
– Connection code 3PD,
between components 1081 and 120.
Also check the engine management computer connectors.
If there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair) repair the wiring, otherwise replace it.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-222V9 MR-372-J84-13B450$131.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET042
CONTINUED 5
SPEED LIMITER
SCENIC II:
When the driver presses the main speed limiter switch, status ET042 becomes
SPEED LIMITER.
If CRUISE CONTROL or INACTIVE appears although the switch was pressed in the
speed limiter position, carry out the following operations:
Check the connections of the cruise control/speed limiter main switch.
Check for +12 V after ignition on the switch connector.
– Connection code AP43 of component 1546.
Disconnect the main switch, and when it is in the rest position, check the insulation
between:
– Connection codes AP43 and 3FX of component 1546.
– Connection codes AP43 and 3PD of component 1546.
Check the continuity between connections AP43 and 3PD of component 1546 in
the speed limiter position.
Check the continuity between connections AP43 and 3FX of component 1546 in
the cruise control position.
If these checks are not in order, replace the switch.
Check the continuity, insulation and the absence of interference resistance on
the following connections:
– Connection code 3FX,
– Connection code 3PD,
between components 1546 and 120.
Also check the engine management computer connectors.
If there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair) repair the wiring, otherwise replace it.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58