2011 Ram 3500 Owner's Manual

RamBoxStorage Bin Cover Emergency Release
Lever — If Equipped
As a security measure, a Storage Bin Cover Emergency
Release is built into the storage bin cover latching mecha-
nism.NOTE:In the event of an individual being locked inside
the storage bin, the storage bin cover can be opened from
inside of the bin by pulling on the glow-in-the-dark lever
attached to the storage bin cover latching mechanism.
Bed Extender — If Equipped
The bed extender has three functional positions:
•Storage Position
•Divider Position
•Extender Position
Storage Position
The storage position for the bed extender is at the front of
the truck bed which maximizes the bed cargo area when
not in use.
Storage Bin Cover Emergency Release Lever
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

To install the bed extender into the storage position,
perform the following:
1. Make sure the center handle is unlocked using the
vehicle key and rotate the center handle vertically to
release the extender side gates.2. With the side gates open, position the extender fully
forward in the bed against the front panel.
Center Handle and Lock
1 — Center Handle Lock 2 — Handle
Storage Position
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185

3. Rotate the side gates closed allowing the outboard
ends to be positioned in front of the cargo tie down loops.
4. Rotate the center handle horizontally to secure the side
gates in the closed position.5. Lock the center handle using the vehicle key to secure
the panel into place and assist against theft.
Cargo Tie Down Loop
Side Gates Closed
186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Divider Position
The divider position is intended for managing your cargo
and assisting in keeping cargo from moving around the
bed. There are 11 divider slots along the bed inner panels
which allow for various positions to assist in managing
your cargo.
To install the bed extender into a divider position per-
form the following:
1. Make sure the center handle is unlocked using the
vehicle key and rotate the center handle vertically to
release the extender side gates.
Center Handle and Lock
1 — Center Handle Lock
2 — Handle
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187

2. With the side gates open, position the extender so the
outboard ends align with the intended slots in the sides
of the bed.
3. Rotate the side gates closed so that the outboard ends
are secured into the intended slots of the bed.4. Rotate the center handle horizontally to secure the side
gates in the closed position.
5. Lock the center handle to secure the panel into place
and assist against theft.
Aligning Gate To Slots
Side Gates Closed
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Extender Position
The extender position allows you to load the bed of the
truck beyond the tail gate. The bed extender will add an
additional 15 in (38 cm) in the back of the truck when
additional cargo room is needed. The extender position
utilizes a locating pin and rotating handle located on both
sides of the truck bed near the tailgate.To install the bed extender into the extender position
perform the following:
1. Lower the tailgate.
2. Make sure the center handle is unlocked and rotate the
center handle vertically in order to release the extender
side gates.
Extender Position
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189

3. Fit the end of the side gate ends onto the pin and
handle.4. Rotate the handles to the horizontal position to secure
into place.
Extender InstallationLocking Tab
190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING!
To reduce the risk of potential injury or property
damage:
•Cargo must be secured.
•Do not exceed cargo load rating of your vehicle.
•Secure all loads to truck utilizing cargo tie downs.
•Extender should not be used as cargo tie down.
•When vehicle is in motion do not exceed 150 lbs
(68 kg) load on the tailgate.
•The bed extender is not intended for off road use.
•When not in use, the extender/divider should be in
stowed or divider position with the tailgate closed.
•When in use all handles are to be in the locked
position.
Bed Rail Tie-Down System
CAUTION!
The maximum load per cleat should not exceed
250 lbs (113 kg) and the angle of the load on each cleat
should not exceed 60 degrees above horizontal, or
damage to the cleat or cleat rail may occur.
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191