Page 464 of 3787
![NISSAN TIIDA 2011 Service Repair Manual AUDIOAV-67
< SERVICE INFORMATION > [AUDIO WITH NAVIGATION]
C
D
E
F
G H
I
J
L
M A
B
AV
N
O P
MALFUNCTION WITH AUDIO
• The majority of the audio malfunctions are the result of outside causes (Malfunct NISSAN TIIDA 2011 Service Repair Manual AUDIOAV-67
< SERVICE INFORMATION > [AUDIO WITH NAVIGATION]
C
D
E
F
G H
I
J
L
M A
B
AV
N
O P
MALFUNCTION WITH AUDIO
• The majority of the audio malfunctions are the result of outside causes (Malfunct](/manual-img/5/57396/w960_57396-463.png)
AUDIOAV-67
< SERVICE INFORMATION > [AUDIO WITH NAVIGATION]
C
D
E
F
G H
I
J
L
M A
B
AV
N
O P
MALFUNCTION WITH AUDIO
• The majority of the audio malfunctions are the result of outside causes (Malfunction CD, electromagnetic interference, etc.). Check the sympt oms below to diagnose the malfunction.
• The vehicle itself can be a source of noise if noise prevention parts or electrical equipment is malfunctioning.
Check if noise is caused and/or changed by engine speed, ignition switch turned to each position, and oper-
ation of each piece of electrical equipment, and then determine the cause.
NOTE:
• CD-R is not guaranteed to play because they can contain compressed audio (MP3, WMA) or could be incorrectly mastered by the customer on a computer.
• Check if the CDs have the Compact Disc logo. If not, the disc is not mastered to the “red book” Compact
Disc standard and may not play.
All switches cannot be operated. Display does not turn ON.
AV control unit power supply and ground
circuit. Refer to
AV- 6 9.
Display turn ON. AV control unit. Refer to AV- 6 9
.
Only specified switch cannot be
operated. –
AV control unit. Refer to AV- 6 9
.
Voice guidance is not heard. Audio sound is normal. AV control unit. Refer to AV- 6 9
.
Display does not dim. Check “Illumination
Signal” in “SERVICE
SYSTEM STATUS”,
“SERVICE MENU”. “Illumination Signal” reaches
100% when the lighting
switch is ON.
AV control unit. Refer to
AV- 7 3
.
“Illumination Signal” does not
reach 100% when the lighting
switch is ON. Illumination signal circuit. Refer to
LT-
109.
Vehicle icon does not move. Check “Speed Signal”
in “SERVICE SYSTEM
STATUS”, “SERVICE
MENU”. A value of “Speed Signal”
changes according to vehicle
speeds.
AV control unit. Refer to
AV- 7 3
.
A value of “Speed Signal”
does not change according to
vehicle speeds. Vehicle speed signal circuit. Refer to
DI-
16.
Map matching is not complete
GPS icon is not displayed Check “GPS Antenna”
in “SERVICE SYSTEM
SELF TEST”, “SER-
VICE MENU”. “Connected” is displayed for
“GPS Antenna”.
AV control unit. Refer to
AV- 7 3
.
“Connected” is not displayed
for “GPS Antenna”. GPS antenna. Refer to
AV- 9 3
.
Traffic information (XM Traffic) is
not received. Radio broadcasts are received.
AV control unit. Refer to AV- 7 3
.
Radio broadcasts are not received. • Radio antenna. Refer to
AV- 9 1
.
• Antenna feeder. Refer to AV- 9 1
.
Symptoms
Check itemsProbable malfunction location / Action to
take
Symptom Probable malfunction location
Audio system does not work normally. • AV control unit power supply and ground circuit. Refer to
AV- 6 9
.
• AV control unit. Refer to AV- 7 3
.
Audio steering wheel switch does not operate proper-
ly. • Remote control signal circuit between steering switch and AV control unit.
Refer to AV- 6 9
.
• Steering wheel audio control switch. Refer to AV- 7 3
.
• AV control unit. Refer to AV- 7 3
.
No sound can be heard from any speakers. • Speaker circuit shorted to ground. Refer to
AV- 5 6
.
• AV control unit. Refer to AV- 7 3
.
No sound can be heard from front speakers. • Audio signal circuit between AV control unit and front speakers. Refer to
AV- 7 0
.
• Front speaker. Refer to AV- 7 3
.
• Front tweeter. Refer to AV- 7 3
.
• AV control unit. Refer to AV- 7 3
.
Revision: May 2010 2011 Versa
Page 467 of 3787
![NISSAN TIIDA 2011 Service Repair Manual AV-70
< SERVICE INFORMATION >[AUDIO WITH NAVIGATION]
AUDIO
4. Check continuity between audio unit and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair harness.
2.SPIRAL CABLE CHECK
1. Disconnect combinati NISSAN TIIDA 2011 Service Repair Manual AV-70
< SERVICE INFORMATION >[AUDIO WITH NAVIGATION]
AUDIO
4. Check continuity between audio unit and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair harness.
2.SPIRAL CABLE CHECK
1. Disconnect combinati](/manual-img/5/57396/w960_57396-466.png)
AV-70
< SERVICE INFORMATION >[AUDIO WITH NAVIGATION]
AUDIO
4. Check continuity between audio unit and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair harness.
2.SPIRAL CABLE CHECK
1. Disconnect combination switch (spiral cable) connector M31.
2. Check continuity between combination switch (spiral cable) ter- minals.
OK or NG
OK >> GO TO 4.
NG >> Replace combination switch (spiral cable). Refer to SRS-37, "
Removal and Installation".
3.CHECK STEERING SWITCH RESISTANCE
Check resistance between combination switch (spiral cable) connector M31 terminals.
OK or NG
OK >> Inspection End.
NG >> Replace steering wheel audio control switch. Refer to AV-73, "
Removal and Installation".
Sound Is Not Heard from Front Door Speaker or Front TweeterINFOID:0000000006216711
1.HARNESS CHECK
Te r m i n a l s
Continuity
AB
Connector Terminal Connector Terminal
M43 6
M30 24
Ye s
15 31
16 32
Te r m i n a l s Continuity
(+)
(–)
Connector Terminal
M43 6
Ground No
15
16
AWNIA1823GB
16 - 32 : Continuity should exist.
17 - 31 : Continuity should exist.
20 - 24 : Continuity should exist.
WKIA4424E
Terminal Signal name ConditionResistance
(Ω)
(Approx.)
16 17 Seek (down) Depress Seek down switch.
165
Phone/ Send Depress Phone/ Send switch. 0
Volume (down) Depress volume down switch. 652
20 17 Seek (up) Depress Seek up switch.
165
Phone/ End Depress Phone/ End switch. 0
Volume (up) Depress volume up switch. 652
LKIA0191E
Revision: May 2010 2011 Versa
Page 468 of 3787
![NISSAN TIIDA 2011 Service Repair Manual AUDIOAV-71
< SERVICE INFORMATION > [AUDIO WITH NAVIGATION]
C
D
E
F
G H
I
J
L
M A
B
AV
N
O P
1. Disconnect AV control unit connector and front door speaker and front tweeter connector (LH or RH).
2. C NISSAN TIIDA 2011 Service Repair Manual AUDIOAV-71
< SERVICE INFORMATION > [AUDIO WITH NAVIGATION]
C
D
E
F
G H
I
J
L
M A
B
AV
N
O P
1. Disconnect AV control unit connector and front door speaker and front tweeter connector (LH or RH).
2. C](/manual-img/5/57396/w960_57396-467.png)
AUDIOAV-71
< SERVICE INFORMATION > [AUDIO WITH NAVIGATION]
C
D
E
F
G H
I
J
L
M A
B
AV
N
O P
1. Disconnect AV control unit connector and front door speaker and front tweeter connector (LH or RH).
2. Check continuity between AV control unit harness connector ter- minal and front door speaker and front tweeter harness connec-
tor terminal.
3. Check continuity between AV control unit harness connector ter- minal and ground.
OK or NG
OK >> GO TO 2.
NG >> • Check connector housings for disconnected or loose terminals. • Repair harness or connector.
2.FRONT SPEAKER SIGNAL CHECK
1. Connect AV control unit connector, front door speaker connector and front tweeter connector.
2. Turn ignition switch to ACC.
3. Push “POWER” switch.
Te r m i n a l s
Continuity
AV control unit Speaker or tweeter
Connector Terminal Connector Terminal
A: M43 2
B: M46 +
Ye s
3-
11 B: M47 +
12 -
2 B: D12 +
3-
11 B: D112 +
12 -
Te r m i n a l s Continuity
AV control unit
—
Connector Terminal
A: M43 2
Ground No
3
11
12
WKIA5444E
Revision: May 2010 2011 Versa
Page 469 of 3787
![NISSAN TIIDA 2011 Service Repair Manual AV-72
< SERVICE INFORMATION >[AUDIO WITH NAVIGATION]
AUDIO
4. Check the signal between AV control unit connector terminals
with CONSULT-III or oscilloscope.
OK or NG
OK >> Replace front speaker. Refer NISSAN TIIDA 2011 Service Repair Manual AV-72
< SERVICE INFORMATION >[AUDIO WITH NAVIGATION]
AUDIO
4. Check the signal between AV control unit connector terminals
with CONSULT-III or oscilloscope.
OK or NG
OK >> Replace front speaker. Refer](/manual-img/5/57396/w960_57396-468.png)
AV-72
< SERVICE INFORMATION >[AUDIO WITH NAVIGATION]
AUDIO
4. Check the signal between AV control unit connector terminals
with CONSULT-III or oscilloscope.
OK or NG
OK >> Replace front speaker. Refer to AV-73, "Removal and
Installation".
NG >> Replace AV control unit. Refer to AV-73, "
Removal and
Installation".
Sound Is Not Heard from Rear SpeakerINFOID:0000000006216712
1.HARNESS CHECK
1. Disconnect AV control unit connector and rear speaker connector.
2. Check continuity between AV control unit harness connector ter- minal and rear speaker harness connector terminal.
3. Check continuity between AV control unit harness connector ter- minal and ground.
OK or NG
OK >> GO TO 2.
NG >> • Check connector housings for disconnected or loose terminals. • Repair harness or connector.
2.REAR SPEAKER SIGNAL CHECK
Te r m i n a l s
Condi-tion Reference
signal
(+)
(-)
Con-
nector Te r m i -
nal Con-
nector Te r m i -
nal
M43 2
M43 3
Receive
audio
signal
11
1 2
WKIA5853E
SKIA0177E
Te r m i n a l s
Continuity
AV control unit Speaker
Connector Terminal Connector Terminal
A: M43 4
B: D207 +
Ye s
5-
13 B: D307 +
14 -
Te r m i n a l s Continuity
AV control unit
—
Connector Terminal
A: M43 4
Ground No
5
13
14
WKIA5353E
Revision: May 2010 2011 Versa
Page 470 of 3787
![NISSAN TIIDA 2011 Service Repair Manual AUDIOAV-73
< SERVICE INFORMATION > [AUDIO WITH NAVIGATION]
C
D
E
F
G H
I
J
L
M A
B
AV
N
O P
1. Connect AV control unit connector and rear speaker connector.
2. Turn ignition switch to ACC.
3. Push “ NISSAN TIIDA 2011 Service Repair Manual AUDIOAV-73
< SERVICE INFORMATION > [AUDIO WITH NAVIGATION]
C
D
E
F
G H
I
J
L
M A
B
AV
N
O P
1. Connect AV control unit connector and rear speaker connector.
2. Turn ignition switch to ACC.
3. Push “](/manual-img/5/57396/w960_57396-469.png)
AUDIOAV-73
< SERVICE INFORMATION > [AUDIO WITH NAVIGATION]
C
D
E
F
G H
I
J
L
M A
B
AV
N
O P
1. Connect AV control unit connector and rear speaker connector.
2. Turn ignition switch to ACC.
3. Push “POWER” switch.
4. Check the signal between AV control unit harness connector ter- minals with CONSULT-III or oscilloscope.
OK or NG
OK >> Replace speaker. Refer to AV-73, "Removal and Instal-
lation".
NG >> Replace AV control unit. Refer to AV-73, "
Removal and
Installation".
Removal and InstallationINFOID:0000000005931322
AUDIO UNIT
Removal
1. Disconnect the battery negative terminal.
2. Remove cluster lid C. Refer to IP-11
.
3. Remove the audio unit screws (A), disconnect the connectors and remove the audio unit (1).
4. Remove the audio unit bracket.
Installation
Installation is in the reverse order of removal.
FRONT DOOR SPEAKER
Removal
1. Remove the front door finisher. Refer to EI-36.
Te r m i n a l s
Condi-tion Reference
signal
(+)
(-)
Con- nec- tor Te r m i -
nal Con-
nec- tor Te r m i -
nal
M43 4
M43 5
Re-
ceive
audio
signal
13
14
WKIA5808E
SKIA0177E
ALNIA1246ZZ
Revision: May 2010 2011 Versa
Page 471 of 3787
AV-74
< SERVICE INFORMATION >[AUDIO WITH NAVIGATION]
AUDIO
2. Remove the front door speaker screws (A), disconnect the con-
nector and remove the front door speaker (1).
Installation
Installation is in the reverse order of removal.
REAR DOOR SPEAKER
Removal
1. Remove the rear door finisher. Refer to EI-36.
2. Remove the rear door finisher screws (A), disconnect the con- nector and remove the rear door speaker (1).
Installation
Installation is in the reverse order of removal.
TWEETER
Removal
1. Remove the front pillar garnish. Refer to EI-41.
2. Remove the tweeter screw (A), disconnect the connector and remove the tweeter (1).
Installation
Installation is in the reverse order of removal.
STEERING WHEEL AUDIO CONTROL SWITCHES
SKIB4728E
SKIB4729E
SKIB4730E
Revision: May 2010 2011 Versa
Page 483 of 3787
AV-86
< SERVICE INFORMATION >[AUDIO WITH NAVIGATION]
TELEPHONE
OK >> GO TO 3.
NG >> Repair harness or connector.
3.CHECK BLUETOOTH VOICE SIGNAL
Check signal between Bluetooth control unit harness connector
B121 terminals 9 and 10.
OK or NG
OK >> Replace AV control unit. Refer to AV-73, "Removal and Installation".
NG >> Replace Bluetooth control unit. Refer to AV-86, "
Removal and Installation".
Removal and InstallationINFOID:0000000005931334
BLUETOOTH CONTROL UNIT
Hatchback
9 – 10:When giving a voice
WKIA5798ESKIB3609E
LKIA0762E
1. Bluetooth control unit bracket 2. Bluetooth control unit
A. Blue tooth control unit bolts
B. BLuetooth antenna feeder harness clip (hatchback only) C. Bluetooth antenna feeder harness con-
nector D. Bluetooth control unit connector
E. Bluetooth control unit bracket screws Front
Revision: May 2010
2011 Versa
Page 484 of 3787
![NISSAN TIIDA 2011 Service Repair Manual TELEPHONEAV-87
< SERVICE INFORMATION > [AUDIO WITH NAVIGATION]
C
D
E
F
G H
I
J
L
M A
B
AV
N
O P
Sedan
Removal
1. For hatchback, remove luggage side lower finisher (RH). Refer to EI-56, "Removal and I NISSAN TIIDA 2011 Service Repair Manual TELEPHONEAV-87
< SERVICE INFORMATION > [AUDIO WITH NAVIGATION]
C
D
E
F
G H
I
J
L
M A
B
AV
N
O P
Sedan
Removal
1. For hatchback, remove luggage side lower finisher (RH). Refer to EI-56, "Removal and I](/manual-img/5/57396/w960_57396-483.png)
TELEPHONEAV-87
< SERVICE INFORMATION > [AUDIO WITH NAVIGATION]
C
D
E
F
G H
I
J
L
M A
B
AV
N
O P
Sedan
Removal
1. For hatchback, remove luggage side lower finisher (RH). Refer to EI-56, "Removal and Installation".
• Disconnect Bluetooth antenna harness clip.
2. For sedan, remove the trunk room side finisher (RH). Refer to EI-59, "
Removal and Installation".
• Disconnect the Bluetooth antenna harness connector.
3. Disconnect the Bluetooth control unit harness connector.
4. Remove the Bluetooth control unit upper and lower bracket bolts.
5. Unhook the Bluetooth control unit upper and lowe r brackets and remove Bluetooth control unit.
6. Remove Bluetooth control unit bracket screws and remove the upper and lower brackets from unit.
Installation
Installation is in the reverse order of removal.
BLUETOOTH ANTENNA
LKIA0936E
1. Bluetooth control unit bracket 2. Bluetooth control unit 3. Bluetooth antenna feeder connector
A. Bluetooth control unit bolts B. Bluetooth control unit connector Front
Revision: May 2010 2011 Versa