2011 Lexus IS220d Owner's Manual

173
2-2. Instrument cluster
2
When driving
IS250/220d/200d_EE
Speed and tacho indicators
Turning the indicator on/off
Bring up the satellite switch
mode on the multi-information
display.
Press “”, “” or the “ON/
OFF” button.
Select the item whose setting is
to be changed.
Press “” or “” to display the
item whose setting is to be
changed.
Change the settings.
Press the “ON/OFF” button to
change the settings.
STEP1
STEP2
STEP3

174
2-2. Instrument cluster
IS250/220d/200d_EEChanging the indicator setting
The satellite switch can be used to change the set speed at which
the yellow speed or tacho indicator ring comes on.
The setting can be made only when the “ENGINE START
STOP” switch is in IGNITION ON mode and the vehicle is
stopped.
Push “
” or “” to select the speed or tacho indicator set mode.
( ) Turn the speed or tacho indicator to “OFF” and then “ON” by
pushing the “ON/OFF” button. ( )
After one second, the mode
enters the indicator setting
mode.
The speedometer or tachometer
needle moves to the previously
set speed.
STEP1

175
2-2. Instrument cluster
2
When driving
IS250/220d/200d_EEPush “
” or “” within 6 seconds of the speedometer or tachome-
ter needle moving to change the setting of the desired speed, then
turn the indicator mode to “ON” by pushing the “ON/OFF” button.
Pushing and holding the switch changes values at a faster rate.
If the satellite switch is not operated for some time, the multi-informa-
tion display returns to its previously displayed content.
The yellow indicator is displayed to indicate that the desired speed
has been set.
STEP2

176
2-2. Instrument cluster
IS250/220d/200d_EE
Speed indicator display conditions and vehicle speed setting range
Vehicle speed setting range:
Right-hand drive vehicles:
Approximately 50 to 160 km/h
(Approximately 30 to 100 mph)
Left-hand drive vehicles:
Approximately 50 to 200 km/h
(Approximately 30 to 125 mph)
When the maximum speed is selected, the speed indicator comes on in red.
Tacho indicator display conditions and engine speed setting range
Engine rpm setting range:
IS250: Approximately 2000 to 6500 rpm (r/min)
IS220d and IS200d: Approximately 2000 to 5100 rpm (r/min)
When the maximum rpm is selected, the tacho indicator comes on in red.
NOTICE
To prevent damage to the engine and its components
Do not let the indicator needle of the tachometer enter the red zone, which
indicates the maximum engine speed.
The engine may be overheating if the temperature gauge is in the red zone
(H). In this case, immediately stop the vehicle in a safe place, and check
the engine after it has cooled completely. (
P. 525)

177
2-2. Instrument cluster
2
When driving
IS250/220d/200d_EE
Indicators and warning lights
The indicator and warning lights on the instrument cluster and center
panel inform the driver of the status of the vehicle’s various systems.
Instrument cluster
The units used on the speedometer, tachometer and fuel gauge display,
indicators and warning lights may differ depending on the model/type.
Center panel

178
2-2. Instrument cluster
IS250/220d/200d_EE
Indicators
The indicators inform the driver of the operating state of the
vehicle’s various systems.
Turn signal indicator
(P. 170)(vehicles
with an
automatic
transmis-
sion)
“ECT SNOW” indica-
tor
(P. 162)
Headlight high beam
indicator (P. 186)(vehicles
with an
automatic
transmis-
sion)“ECT PWR” indicator
(P. 162)
Tail light indicator
(P. 186)
(if
equipped)
Cruise control indicator
(P. 198, 202)
Front fog light indicator
(P. 190)
(if
equipped)
Lexus parking assist-
sensor indicator (P.
217)
Rear fog light indicator
(P. 190)Slip indicator
(P. 224)
(vehicles with an automatic
VSC off indicator
(P. 224)
*1, 2
*1

179
2-2. Instrument cluster
2
When driving
IS250/220d/200d_EE
*1:These lights turn on when the “ENGINE START STOP” switch is
turned to IGNITION ON mode to indicate that a system check is
being performed. They will turn off after the engine is started, or
after a few seconds. There may be a malfunction in a system if a
light does not come on, or if the lights do not turn off. Have the
vehicle inspected by any authorized Lexus dealer or repairer, or
another duly qualified and equipped professional, for details.
*2:The light flashes to indicate that the system is operating
(if
equipped)
Daytime running light
system off indicator
(P. 188)SRS airbag on-off indi-
cator (P. 140)
(vehicles
with a man-
ual trans-
mission)Engine preheating indi-
cator (P. 156)
*1

180
2-2. Instrument cluster
IS250/220d/200d_EE
CAUTION
If a safety system warning light does not come on
Should a safety system light such as the ABS and SRS warning light not
come on when you start the engine, this could mean that these systems are
not available to help protect you in an accident, which could result in death
or serious injury. Have the vehicle inspected by any authorized Lexus dealer
or repairer, or another duly qualified and equipped professional, immedi-
ately if this occurs.
Warning lights
Warning lights inform the driver of malfunctions in any of the
vehicle’s systems. (P. 467)
*:These lights turn on when the “ENGINE START STOP” switch is
turned to IGNITION ON mode to indicate that a system check is
being performed. They will turn off after the engine is started, or
after a few seconds. There may be a malfunction in a system if a
light does not come on, or if the lights do not turn off. Have the
vehicle inspected by any authorized Lexus dealer or repairer, or
(vehicles
with a
manual
transmis-
sion)
(if equipped)(for
driver)(for front
passen-
ger)
*****
*****