2011 INFINITI QX56 torque

DIAGNOSIS SYSTEM (TRANSFER CONTROL UNIT)
DLN-23
< SYSTEM DESCRIPTION > [TRANSFER: ATX90A]
C
EF
G H
I
J
K L
M A
B
DLN
N
O P
WORK SUPPORT
*: “LOCK SLEEVE SENSOR” means transfer lock position sensor.
VHCL/S SEN-RR [km/h] X Wheel speed (rear) average calculated by
transfer control.
ENG SPEED [rpm] X Engine status via CAN communication line is
displayed.
INTERNL SPEED SEN [count] X Transfer internal speed sensor status is dis-
played.
TRANSFER TORQUE [Nm] X Commanded transfer communication torque is
displayed.
UNIT PARAMETER [A1 - A9, B1 - B9, C1 - C9, D1
- D9, E1 - E9, F1 - F9, G1 - G9, H1 - H9, J1 - J9] Unit parameter of transfer recognized by trans-
fer control unit is displayed.
Monitor item (Unit)
SELECT MONITOR ITEM
Remarks
ECU INPUT
SIGNALS MAIN SIG-
NALS
Function Description
UNIT CHARACTERISTIC WRITE Writes the unit parameter of transfer to transfer control unit.
START CALIBRATION Perform initial calibration of transfer control unit.
LOCK SLEEVE SENSOR
* INITIALIZE Format learning the transfer lock position sensor written to transfer control unit.
LOCK SLEEVE SENSOR
* LEARNING Perform learning the transfer lock position sensor.
OIL DETERIORATION INFO RESET Format the transfer fl uid viscosity written to transfer control unit.
Revision: 2010 May2011 QX56

DLN-26
< ECU DIAGNOSIS INFORMATION >[TRANSFER: ATX90A]
TRANSFER CONTROL UNIT
*1: 4WD shift swich (2WD) is not equipped, but it is displayed.
*2: This indicator is not equipped, but it is displayed.
*3: This switch is not equipped, but it is displayed.
TERMINAL LAYOUT
PHYSICAL VALUES
COMPR VHCL SPEEDVehicle stopped 0.00 km/h (0.00 mph)
Vehicle driving
CAUTION:
Check air pressure of tire under standard condition. Approx. equal to the indication
on speedometer (inside of ±10
%)
VHCL/S SEN-FR Vehicle stopped 0.00 km/h (0.00 mph)
Vehicle driving
CAUTION:
Check air pressure of tire under standard condition. Approx. equal to the indication
on speedometer (inside of ±10
%)
VHCL/S SEN-RR Vehicle stopped 0.00 km/h
Vehicle driving
CAUTION:
Check air pressure of tire under standard condition. Approx. equal to the indication
on speedometer (inside of ±10
%)
ENGINE SPEED Engine running Approx. equal to the indication
on tachometer (inside of ±10 %)
INTRNL SPEED SEN 4WD mode: AUTO
A/T shift selector: DDepress the accelerator pedal several
times.
Value is changing
TRANSFER TORQUE 4WD shift switch: AUTO 0 - 2250 N·m
4WD shift switch: 4H 0 - 2250 N·m
4WD shift switch: 4L 0 Nm
UNIT PARAMETER Always A1 - A9
B1 - B9
C1 - C9
D1 - D9
E1 - E9F1 - F9
G1 - G9 H1 - H9 J1 - J9
Monitor item Condition Value/Status
JPDIE0229ZZ
Te r m i n a l N o .
(Wire color) Description
Condition Value (Approx.)
+ - Signal name Input/
Output
6
(BR) Ground Hi-Lo position sensor 1 Input/
Output Engine run-
ning
(Never
drive the
vehicle.) 4WD mode: AUTO or 4H 0 V
4WD mode: Shifting 0 V
4WD mode: 4L 5 V
Revision: 2010 May2011 QX56

DLN-28
< ECU DIAGNOSIS INFORMATION >[TRANSFER: ATX90A]
TRANSFER CONTROL UNIT
CAUTION:
When using circuit tester to measure voltage for in
spection, be sure not to extend forcibly any con-
nector terminals.
Fail-SafeINFOID:0000000006222228
 If any malfunction occurs in 4WD electrical system, and control unit detects the malfunction, 4WD warning
lamp on combination meter turns ON to indicate system malfunction.
 When 4WD warning lamp is ON, vehicle changes to rear-wheel drive or shifts to 4-wheel drive (front-wheels
still have some driving torque).
29
(LG/R) Ground Hi-Lo position sensor 2
Input/
Output Engine
running
(Never
drive the
vehicle.)
Always 0 V
30
(R/B) Ground Transfer lock position
sensor (GND) —Always 0 V
31
(L/O) Ground Transfer internal speed
sensor (DIR)
Input IGN ONWhen changing the trans-
fer motor rota
tion direc-
tion.
32
(BR/R) Ground IGN SW Input IGN ON Battery voltage
IGN OFF 0V
35
(R) Ground 4WD shift SW (4H) Input IGN ON 4WD shift switch: 4H Battery voltage
4WD shift switch: Except
4H
0 V
36
(L/R) Ground Transfer fluid tempera-
ture sensor (GND)
—Always 0 V
38
(G/O) Ground
Transfer lock position
sensor signal Input IGN ON
39
(R/W) Ground Transfer internal speed
sensor power supply
InputIGN ON 8 V
IGN OFF 0V
41
(W/R) Ground Transfer control actuator
power supply Input Always Battery voltage
43
(G/R) Ground Motor drive B Input/
Output Transfer motor driving 0V - Battery voltage
44
(B) Ground GND — Always 0 V
45
(G/Y) Ground Motor drive A Input/
Output Transfer motor driving 0V - Battery voltage
46
(B) Ground Transfer control actuator
(GND)
—Always 0 V
Te r m i n a l N o .
(Wire color) Description
Condition Value (Approx.)
+ - Signal name Input/
Output
JPDIE0269GB
JPDIE0268GB
Revision: 2010 May2011 QX56

DLN-102
< SYMPTOM DIAGNOSIS >[TRANSFER: ATX90A]
4WD WARNING LAMP BLINKS QUICKLY
4WD WARNING LAMP BLINKS QUICKLY
DescriptionINFOID:0000000006222318
While driving, 4WD warning lamp blinks 2 times in 1 second and it turns OFF after 1 minute.
 This symptom protects drivetrain parts when a heavy
load is applied to the electric controlled coupling and
multiple disc clutch temperature increases. Also, opt ional distribution of torque sometimes becomes rigid
before lamp blinks quickly. Both cases are not malfunction.
 When this symptom occurs, stop vehicle and allow it to idle for some times. Blinking will stop and system will be restored.
Revision: 2010 May2011 QX56

DLN-106
< PERIODIC MAINTENANCE >[TRANSFER: ATX90A]
TRANSFER FLUID
PERIODIC MAINTENANCE
TRANSFER FLUID
InspectionINFOID:0000000006222324
FLUID LEAKAGE
Check transfer surrounding area (oil seal, drain plug, and filler plug etc.) for fluid leakage.
FLUID LEVEL
1. Remove filler plug (1) and gasket. Then check that fluid is filled
up from mounting hole for the filler plug.
CAUTION:
Never start engine whil e checking fluid level.
2. Set a new gasket onto filler plug (1), and install it on transfer and then tighten to the specified torque.
CAUTION:
Never reuse gasket.
DrainingINFOID:0000000006222325
1. Run the vehicle to warm up the transfer unit sufficiently.
2. Stop the engine.
3. Remove the drain plug (1) and drain transfer fluid.
4. Set a new gasket onto drain plug (1), and install it to transfer andtighten to the specified torque.
CAUTION:
Never reuse gasket.
RefillingINFOID:0000000006222326
1. Remove filler plug (1). Fill up with new transfer fluid up to mount-ing hole for the filler plug.
CAUTION:
Carefully fill the fluid. (Fill up for approximately 3 minutes.)
2. Leave the vehicle for 3 minutes, and check the fluid level again.
3. Set a new gasket onto filler plug, and install it on transfer and tighten to the specified torque.
CAUTION:
Never reuse gasket.
4. Perform learning of transfer fluid viscosity. Refer to DLN-47, "
Work Procedure".
Specified torque : 33 N·m (3.4 kg-m, 24 ft-lb)
JPDIE0295ZZ
Specified torque : 33 N-m (3.4 kg-m, 24 ft-lb)
JPDIE0245ZZ
Fluid grade and Viscosity : Refer to
MA-10, "Fluids
and Lubricants".
Fluid capacity : Refer to DLN-124, "
Gen-
eral Specifications".
Specified torque : 33 N-m (3.4 kg-m, 24 ft-lb)
JPDIE0295ZZ
Revision: 2010 May2011 QX56

DLN-110
< REMOVAL AND INSTALLATION >[TRANSFER: ATX90A]
FRONT OIL SEAL
1. Install front oil seal with a drift (A) (commercial service tool)
within the dimension (L) shown as follows.
CAUTION:
 Never reuse front oil seal.
 Apply transfer fluid onto circumference of oil seal.
2. Install the dust shield to the front shaft flange.
3. Install the front shaft flange.
4. Install the snap ring. CAUTION:
Never reuse the snap ring.
5. Install the O-ring to plug. CAUTION:
 Never reuse the O-ring.
 Never damage the O-ring.
6. Tighten the plug to specified torque.
7. Install front propeller shaft. Refer to DLN-129, "
Removal and Installation".
8. Fill with new transfer fluid, check fluid level and for fluid leakage. Refer to DLN-106, "
Inspection".
L : 5.3 – 5.7 mm
JPDIE0160ZZ
Revision: 2010 May2011 QX56

DLN-122
< UNIT REMOVAL AND INSTALLATION >[TRANSFER: ATX90A]
TRANSFER ASSEMBLY
 When installing the transfer to the
transmission, install the mount-
ing bolts following the standard below, tighten bolts to the specified
torque.
 When installing transfer breather hose, make sure t here are no pinched or restricted areas on the transfer
breather hose caused by bending or winding.
- Install the transfer breather hose (1) of transmission side with the
paint mark (A) facing upward and the mark (B) (: ) facing right
side.
- Install the transfer breather hose (1) of transfer side with the paint mark (A) facing upward, and insert breather hose to breather tube
(2) until dimension (B) shown as follows.
- Be sure to fix breather hose in (A) and (B) positions. Fix with the
paint mark facing upward in the (A) position.
 Check oil level and check for oil leakage after installation. Refer to DLN-106, "
Inspection".
 If replacing transfer assembly, perform writing unit parameter,
learning of fluid viscosity and initial calibration. Refer to DLN-42,
"Work Procedure".
Bolt symbol A B
Insertion direction Transfer to transmission Transmission to transfer
: Tightening the bolt with bracket
JPDIE0259ZZ
JPDIE0247ZZ
B: 20 mm (0.79 in)
JPDIE0251ZZ
JPDIE0248ZZ
Revision: 2010 May2011 QX56

DLN-126
< SYMPTOM DIAGNOSIS >[FRONT PROPELLER SHAFT: 2F P15]
NOISE, VIBRATION, AND HARSHNESS
(NVH) TROUBLESHOOTING
SYMPTOM DIAGNOSIS
NOISE, VIBRATION, AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting ChartINFOID:0000000006222354
Use the chart below to help you find the cause of the symptom. If necessa ry, repair or replace these parts.
×: ApplicableReference
DLN-127, "
Inspection
"—
—
—
—
DLN-127, "
Inspection
"
DLN-127, "
Inspection
"
NVH of FRONT FINAL DRI VE in this section.
NVH of REAR FINAL DRI VE in this section.
NVH in FAX, RAX, FSU and RSU section.
NVH in WT section.
NVH in WT section.
NVH in FAX and RAX section.
NVH in BR section.
NVH in ST section.
Possible cause an d SUSPECTED PARTS
Uneven rotating torque
Center bearing improper installation
Excessive center bearing axial end play
Center bearing mounting (insulator) cracks, damage or deterioration
Excessive joint angle
Rotation imbalance
Excessive runout
DIFFERENTIAL
AXLE AND SUSPENSION
TIRE
ROAD WHEEL
DRIVE SHAFT
BRAKE
STEERING
Symptom Noise
××××××××××××××
Shake × × ××××××
Vibration ××××××× ×× × ×
Revision: 2010 May2011 QX56