2011 INFINITI QX56 oil pressure

DAS-340
< BASIC INSPECTION >[LDW & LDP]
CAMERA AIMING ADJUSTMENT
CAMERA AIMING ADJUSTMENT
DescriptionINFOID:0000000006223734
Always adjust the camera aiming after removing
and installing or replacing the lane camera unit.
CAUTION:
 Place the vehicle on level ground when th e camera aiming adjustment is operated.
 Follow the CONSULT-III when performing the came ra aiming. (Camera aiming adjustment cannot be
operated without CONSULT-III.)
Work Procedure (Preparation)INFOID:0000000006223735
1.PERFORM SELF-DIAGNOSIS
Perform self-diagnosis of ADAS control unit and lane camera unit.
Is any DTC detected?
Except “C1B01”>>Perform diagnosis on the detected DTC and repair or replace the applicable item. Refer to
DAS-310, "
DTC Index" (ICC/ADAS) or DAS-316, "DTC Index" (LANE CAMERA).
“C1B01” or no DTC>>GO TO 2.
2.PREPARATION BEFORE CAMERA AIMING ADJUSTMENT
1. Perform pre-inspection for diagnosis. Refer to DAS-335, "
Inspection Procedure".
2. Adjust the tire pressure to the specified pressure value.
3. Maintain no-load in vehicle.
4. Check if coolant and engine oil are filled up to correct level and fuel tank is full.
5. Shift the selector lever to “P” position and release the parking brake.
6. Clean the windshield.
7. Completely clear off the instrument panel.
>> GO TO 3.
3. PREPARATION OF AIMING ADJUSTMENT JIG
Prepare the aiming adjustment jig according to the following procedure and the figure.
1. Print out the target mark attached in this service manual. Refer to DAS-343, "
Work Procedure (Target
Mark Sample)".
2. Stick a printed target mark on the board with a scotch tape or a piece of double-sided tape.
NOTE:
 Use the board that peripheral area of the ta rget is monochrome such as a white-board.
 Notice that the cross of the target is horizontal and vertical.
JPOIA0011ZZ
Revision: 2010 May2011 QX56

DEF-10
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (IPDM E/R)
DIAGNOSIS SYSTEM (IPDM E/R)
Diagnosis DescriptionINFOID:0000000006349776
AUTO ACTIVE TEST
Description
In auto active test, the IPDM E/R sends a drive signal to the following systems to check their operation.
 Oil pressure warning lamp
 Rear window defogger
 Front wiper (LO, HI)
 Parking lamp
 License plate lamp
 Tail lamp
 Side marker lamp
 Front fog lamp
 Headlamp (LO, HI)
 A/C compressor (magnet clutch)
Operation Procedure
CAUTION:
Never perform auto active test in the following conditions.
 Engine is running.
 CONSULT-III is connected.
1. Close the hood and lift the wiper arms from the windshield. (Prevent windshield damage due to wiper
operation)
NOTE:
When auto active test is performed with hood opened, sprinkle water on windshield beforehand.
2. Turn the ignition switch OFF.
3. Turn the ignition switch ON, and within 20 seconds, pr ess the driver door switch 10 times. Then turn the
ignition switch OFF.
CAUTION:
Close passenger door.
4. Turn the ignition switch ON within 10 seconds. Af ter that the horn sounds once and the auto active test
starts.
CAUTION:
Engine starts when igniti on switch is turned ON while brake pedal is depressed.
5. The oil pressure warning lamp starts blinking when the auto active test starts.
6. After a series of the following operations is repeated 3 times, auto active test is completed.
NOTE:
 When auto active test has to be cancelled halfway through test, turn the ignition switch OFF.
 When auto active test is not activated, door swit ch may be the cause. Check door switch. Refer to DLK-117,
"ComponentFunctionCheck".
Inspection in Auto Active Test
When auto active test is actuated, the following operation sequence is repeated 3 times.
Operation
sequence Inspection location Operation
1 Oil pressure warning lamp Blinks continuously during operation of auto active test
2 Rear window defogger 10 seconds
3 Front wiper LO for 5 seconds → HI for 5 seconds
4 Parking lamp
 License plate lamp
 Tail lamp
 Side marker lamp
 Front fog lamp 10 seconds
Revision: 2010 May2011 QX56

DEF-12
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (IPDM E/R)
CONSULT-III Function (IPDM E/R)
INFOID:0000000006349777
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with IPDM E/R.
SELF DIAGNOSTIC RESULT
Refer to PCS-22, "DTCIndex".
DATA MONITOR
Monitor item
Oil pressure warning lamp does not operate Perform auto active test.
Does the oil pressure warning
lamp blink?YES
 Harness or connector be-
tween IPDM E/R and oil
pressure switch
 Oil pressure switch
IPDM E/R
NO  CAN communication signal
between IPDM E/R and
BCM
 CAN communication signal
between BCM and combi-
nation meter
 Combination meter
Symptom Inspection contents Possible cause
Diagnosis mode Description
Ecu Identification Allows confirmation of IPDM E/R part number.
Self Diagnostic Result Displays the diagnosis results judged by IPDM E/R.
Data Monitor Displays the real-time input/output data from IPDM E/R input/output data.
Active Test IPDM E/R can provide a drive signal to electronic components to check their operations.
CAN Diag Support Monitor The results of transmit/receive diagnosis of CAN communication can be read.
Monitor Item [Unit] MAIN SIG-
NALS Description
RAD FAN REQ
[1/2/3/4] ×Displays the value of the cooling fan speed request signal received from ECM via
CAN communication.
AC COMP REQ
[Off/On] ×Displays the status of the A/C compressor request signal received from ECM via
CAN communication.
TA I L & C L R R E Q
[Off/On] ×
Displays the status of the position light request signal received from BCM via CAN
communication.
HL LO REQ
[Off/On] ×Displays the status of the low beam request signal received from BCM via CAN
communication.
HL HI REQ
[Off/On] ×Displays the status of the high beam request signal received from BCM via CAN
communication.
FR FOG REQ
[Off/On] ×Displays the status of the front fog light request signal received from BCM via
CAN communication.
FR WIP REQ
[Stop/1LOW/Low/Hi] ×
Displays the status of the front wiper request signal received from BCM via CAN
communication.
WIP AUTO STOP
[STOP P/ACT P] ×
Displays the status of the front wiper auto stop signal judged by IPDM E/R.
WIP PROT
[Off/BLOCK] ×
Displays the status of the front wiper fail-safe operation judged by IPDM E/R.
IGN RLY1 -REQ
[Off/On] Displays the status of the ignition switch ON signal received from BCM via CAN
communication.
IGN RLY
[Off/On] ×
Displays the status of the ignition relay judged by IPDM E/R.
Revision: 2010 May2011 QX56

DIAGNOSIS SYSTEM (IPDM E/R)DEF-13
< SYSTEM DESCRIPTION >
C
DE
F
G H
I
J
K
M A
B
DEF
N
O P
ACTIVE TEST
Te s t i t e m
PUSH SW
[Off/On] Displays the status of the push-button ignition switch judged by IPDM E/R.
INTER/NP SW
[Off/On] Displays the status of the shift position judged by IPDM E/R.
ST RLY CONT
[Off/On] Displays the status of the starter relay status signal received from BCM via CAN
communication.
IHBT RLY -REQ
[Off/On] Displays the status of the starter control relay signal received from BCM via CAN
communication.
ST/INHI RLY
[Off/ ST ON/INHI ON/UNKWN] Displays the status of the starter relay and starter control relay judged by IPDM
E/R.
DETENT SW
[Off/On] Displays the status of the A/T shift selector (detention switch) judged by IPDM E/
R.
S/L RLY -REQ
[Off/On] Displays the status of the steering lock relay signal received from BCM via CAN
communication.
S/L STATE
[LOCK/UNLK/UNKWN] Displays the status of the steering lock judged by IPDM E/R.
OIL P SW
[Open/Close] Displays the status of the oil pressure switch judged by IPDM E/R.
HOOD SW
[Off/On] Displays the status of the hood switch judged by IPDM E/R.
HL WASHER REQ
[Off/On] Displays the status of the headlamp washer request signal received from BCM via
CAN communication.
THFT HRN REQ
[Off/On] Displays the status of the theft warning horn request signal received from BCM
via CAN communication.
HORN CHIRP
[Off/On] Displays the status of the horn reminder signal received from BCM via CAN com-
munication.
Monitor Item
[Unit] MAIN SIG-
NALS Description
Test item Operation Description
CORNERING LAMP LH
NOTE:
This item is indicated, but cannot be tested.
RH
HORN On Operates horn relay for 20 ms.
REAR DEFOGGER Off OFF
On Operates the rear window defogger relay.
FRONT WIPER Off OFF
Lo Operates the front wiper relay.
Hi Operates the front wiper relay and front wiper high relay.
MOTOR FAN* 1OFF
2 Transmits 50% pulse duty signal (PWM signal) to the cooling fan control module.
3 Transmits 75% pulse duty signal (PWM signal) to the cooling fan control module.
4
Transmits 100% pulse duty signal (PWM signal) to the cooling fan control mod-
ule.
HEAD LAMP WASHER On Operates the headlamp washer relay for 1 second.
Revision: 2010 May2011 QX56

DLK-252
< REMOVAL AND INSTALLATION >
CAB MOUNTING INSULATOR
 Drain brake fluid from brake line. Refer to BR-10, "Draining".
 Release fuel pressure. Refer to EC-153, "
Work Procedure".
 Disconnect both battery cables. Refer to PG-164, "
Removal and Installation".
 Drain engine coolant from radiator. Refer to CO-8, "
Draining".
 Discharge refrigerant from A/C circuit. Refer to HA-20, "
Recycle Refrigerant".
 Drain power steering fluid from reservoir tank.
4. Remove parts relating to connection of body assembly and frame assembly.  Tire and wheel: Refer to WT-64, "
Removal and Installation" (with TPMS).
 Front fender protector (LH and RH): Refer to EXT-23, "
FENDER PROTECTOR : Removal and Installa-
tion".
 Front bumper: Refer to EXT-13, "
Removal and Installation".
 Radiator core support upper: Refer to DLK-220, "
Removal and Installation".
 Fan shroud: Refer to CO-16, "
Removal and Installation".
 Battery and battery case: Refer to PG-164, "
Removal and Installation".
 Air cleaner case (upper and lower): Refer to EM-27, "
Removal and Installation".
 Engine cover: Refer to EM-25, "
Removal and Installation".
 Rear wheel house protector (LH and RH): EXT-24, "
REAR WHEEL HOUSE PROTECTOR : Removal
and Installation".
 Rear bumper: Refer to EXT-17, "
Removal and Installation".
 Fuel filler tube: Remove to FL-8, "
Exploded View".
 Spare tire
 Towing hook bracket.
5. Separate parts relating to connection of body assembly and frame assembly. Vehicle front
 Disconnect ICC sensor connector. (models with ICC) Refer to CCS-176, "
Removal and Installation".
 Remove radiator upper hose and radiator lower hose from radiator assembly. Refer to CO-13,
"Exploded View".
 Remove A/T fluid cooler hose B and A/T fluid cooler hose E from A/T fluid cooler tubes. Refer to TM-
202, "Exploded View".
 Remove power steering return hose from oil cooler, and then power steering return hose clamp bolt from frame assembly. Refer to ST-54, "
Exploded View".
 Remove power steering suction hose from reservoir tank. Refer to ST-54, "
Exploded View".
CAUTION:
Never spill power steering fluid in engine room.
 Remove A/C low-presser flexible hose from A/C low-presser pipe. Refer to HA-35, "
LOW-PRESSURE
FLEXIBLE HOSE : Removal and Installation".
 Remove A/C hi-presser flexible hose from condenser. Refer to HA-34, "
HIGH-PRESSURE FLEXIBLE
HOSE : Removal and Installation".
 Remove all engine Control Harness connectors, har ness clips and others that are connected to the
body assembly side of the engine room. (engine room LH and RH side). Refer to PG-148, "
Engine Con-
trol Harness".
NOTE:
Separate harness connectors from ECM (engine control module). Refer to EC-10, "
General Precau-
tions".
CAUTION:
 When pulling out harnesses, never damage harnesses or connectors.
 After temporarily securing connectors, cover th em with vinyl or similar material to protect
against adhesion of foreign materials.
 Disconnect engine room harness connectors and remo ve harness clips from engine assembly (engine
RH side). Refer to PG-146, "
Engine Room Harness".
 Remove heater hoses from front water outlet tube (engine room RH side). Refer to HA-33, "
Exploded
View".
 Disconnect front wheel sensor connectors (LH and RH). Refer to BRC-134, "
FRONT WHEEL SENSOR
: Exploded View".
 Disconnect fuel feed tube and EVAP hos e (front wheel well LH side).
 Remove steering lower shaft from steering gear side assembly. Refer to ST-37, "
Removal and Installa-
tion"
CAUTION:
Spiral cable may be cut if steering wheel turns while separating steering column assembly and
steering gear assembly.
Revision: 2010 May2011 QX56

EC-1
ENGINE
C
DE
F
G H
I
J
K L
M
SECTION EC
A
EC
N
O P
CONTENTS
ENGINE CONTROL SYSTEM
VK56VD
PRECAUTION ................ ...............................
9
PRECAUTIONS .............................................. .....9
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ............................................................. ......
9
Precaution for Procedure without Cowl Top Cover ......9
Precautions For Xenon Headlamp Service ...............9
On Board Diagnostic (OBD) System of Engine
and A/T ....................................................................
10
General Precautions ...............................................10
PREPARATION ...........................................14
PREPARATION .............................................. ....14
Special Service Tools .......................................... ....14
Commercial Service Tools ......................................14
SYSTEM DESCRIPTION .............................16
COMPONENT PARTS ................................... ....16
Component Parts Location .................................. ....16
Component Description ...........................................19
Accelerator Pedal Position Sensor ..........................21
Air Fuel Ratio (A/F) Sensor 1 ..................................21
ASCD Brake Switch & Stop Lamp Switch ...............21
ASCD Steering Switch ............................................21
ASCD Indicators ......................................................21
Battery Current Sensor (With Battery Tempera-
ture Sensor) ............................................................
22
Camshaft Position Sensor .......................................22
Crankshaft Position Sensor .....................................23
ECM ........................................................................23
Electric Throttle Control Actuator ............................23
Electrically-controlled cooling fan coupling .............24
Engine Coolant Temperature Sensor ......................25
Engine Oil Temperature Sensor ..............................25
EVAP Control System Pressure Sensor .................26
EVAP Canister Vent Control Valve .........................26
EVAP Canister Purge Volume Control Solenoid
Valve .................................................................... ....
26
Fuel Injector .............................................................26
Fuel Level Sensor ....................................................26
Fuel Pump Control Module ......................................27
Fuel Rail Pressure Sensor .......................................27
Fuel Tank Temperature Sensor ...............................27
Heated Oxygen Sensor 2 ........................................27
High Pressure Fuel Pump .......................................28
ICC Brake Switch & Stop Lamp Switch ...................29
ICC Steering Switch ................................................29
Ignition Coil With Power Transistor .........................29
Intake Valve Timing Control Solenoid Valve ...........29
Knock Sensor ...................................................... ....30
Low Fuel Pressure Sensor ......................................30
Low Pressure Fuel Pump ........................................30
Malfunction Indicator Lamp (MIL) ............................30
Manifold Absolute Pressure Sensor ........................31
Mass Air Flow Sensor (With Intake Air Tempera-
ture Sensor) .............................................................
31
Power Steering Pressure (PSP) Sensor ..................31
Refrigerant Pressure Sensor ............................... ....32
VVEL Actuator Motor ...............................................32
VVEL Actuator Motor Relay .....................................32
VVEL Control Module ..............................................32
VVEL Control Shaft Position Sensor .......................32
STRUCTURE AND OPERATION .....................33
Positive Crankcase Ventilation ................................33
On Board Refueling Vapor Recovery (ORVR) ........34
SYSTEM ............................................................35
ENGINE CONTROL SYSTEM ........................ ...........35
ENGINE CONTROL SYSTEM : System Diagram ....35
ENGINE CONTROL SYSTEM : System Descrip-
tion ...........................................................................
35
DIRECT INJECTION GASOLINE SYSTEM .......... ....36
DIRECT INJECTION GASOLINE SYSTEM :
System Diagram .....................................................
36
Revision: 2010 May2011 QX56

EC-4
Component Inspection (Engine Coolant Tempera-
ture Sensor) ...........................................................
216
P0117, P0118 ECT SENSOR ..........................217
DTC Logic ............................................................ ..217
Diagnosis Procedure .............................................217
Component Inspection (Engine Coolant Tempera-
ture Sensor) ...........................................................
218
P0122, P0123 TP SENSOR .............................219
DTC Logic ............................................................ ..219
Diagnosis Procedure .............................................219
Component Inspection (Throttle Position Sensor) ..220
P0125 ECT SENSOR .......................................222
DTC Logic ............................................................ ..222
Diagnosis Procedure .............................................222
Component Inspection (Engine Coolant Tempera-
ture Sensor) ...........................................................
223
P0127 IAT SENSOR ........................................224
DTC Logic ............................................................ ..224
Diagnosis Procedure .............................................224
Component Inspection (Intake Air Temperature
Sensor) ..................................................................
225
P0128 THERMOSTAT FUNCTION .................226
DTC Logic ............................................................ ..226
Diagnosis Procedure .............................................227
Component Inspection (Engine Coolant Tempera-
ture Sensor) ...........................................................
227
P0130, P0150 A/F SENSOR 1 .........................228
DTC Logic ............................................................ ..228
Component Function Check ..................................229
Diagnosis Procedure .............................................230
P0131, P0151 A/F SENSOR 1 .........................232
DTC Logic ............................................................ ..232
Diagnosis Procedure .............................................233
P0132, P0152 A/F SENSOR 1 .........................235
DTC Logic ............................................................ ..235
Diagnosis Procedure .............................................236
P0133, P0153 A/F SENSOR 1 .........................238
DTC Logic ............................................................ ..238
Diagnosis Procedure .............................................239
P0137, P0157 HO2S2 ......................................243
DTC Logic ............................................................ ..243
Component Function Check ..................................244
Diagnosis Procedure .............................................245
Component Inspection (HO2 sensor 2) .................246
P0138, P0158 HO2S2 ......................................249
DTC Logic ............................................................ ..249
Component Function Check ..................................251
Diagnosis Procedure .............................................251
Component Inspection (HO2 sensor 2) .................254
P0139, P0159 HO2S2 .......................................257
DTC Logic ............................................................ .257
Component Function Check .................................258
Diagnosis Procedure .............................................259
Component Inspection (HO2 sensor 2) ................260
P0171, P0174 FUEL INJECTION SYSTEM
FUNCTION ........................................................
263
DTC Logic ............................................................ .263
Diagnosis Procedure .............................................264
P0172, P0175 FUEL INJECTION SYSTEM
FUNCTION ........................................................
267
DTC Logic ............................................................ .267
Diagnosis Procedure .............................................268
P0181 FTT SENSOR ........................................271
DTC Logic ............................................................ .271
Diagnosis Procedure .............................................271
Component Inspection (Fuel Tank Temperature
Sensor) .................................................................
273
P0182, P0183 FTT SENSOR ............................274
DTC Logic ............................................................ .274
Diagnosis Procedure .............................................274
Component Inspection (Fuel Tank Temperature
Sensor) .................................................................
275
P0190, P0192, P0193 FRP SENSOR ...............276
DTC Logic ............................................................ .276
Diagnosis Procedure .............................................276
Component Inspection (Fuel Rail Pressure Sen-
sor) ........................................................................
278
P0191 FRP SENSOR .......................................279
DTC Logic ............................................................ .279
Diagnosis Procedure .............................................279
Component Inspection (Fuel Rail Pressure Sen-
sor) ........................................................................
281
P0196 EOT SENSOR .......................................283
DTC Logic ............................................................ .283
Diagnosis Procedure .............................................284
Component Inspection (Engine Oil Temperature
Sensor) .................................................................
284
P0197, P0198 EOT SENSOR ...........................285
DTC Logic ............................................................ .285
Diagnosis Procedure .............................................285
Component Inspection (Engine Oil Temperature
Sensor) .................................................................
286
P0201, P0202, P0203, P0204, P0205, P0206,
P0207, P0208 INJECTOR ................................
287
DTC Logic ............................................................ .287
Diagnosis Procedure .............................................287
P0222, P0223 TP SENSOR ..............................288
DTC Logic ............................................................ .288
Diagnosis Procedure .............................................288
Component Inspection (Throttle Position Sensor) .289
Revision: 2010 May2011 QX56

EC-5
C
DE
F
G H
I
J
K L
M
EC A
N
O P
P0300, P0301, P0302, P0303, P0304, P0305,
P0306, P0307, P0308 MISFIRE ..................... ..
291
DTC Logic ........................................................... ..291
Diagnosis Procedure .............................................292
P0327, P0328, P0332, P0333 KS ....................297
DTC Logic ........................................................... ..297
Diagnosis Procedure .............................................297
Component Inspection (Knock Sensor) ................298
P0335 CKP SENSOR .......................................299
DTC Logic ........................................................... ..299
Diagnosis Procedure .............................................299
Component Inspection (Crankshaft Position Sen-
sor) ........................................................................
301
P0340, P0345 CMP SENSOR ..........................303
DTC Logic ........................................................... ..303
Diagnosis Procedure .............................................304
Component Inspection (Camshaft Position Sen-
sor) ........................................................................
306
P0420, P0430 THREE WAY CATALYST
FUNCTION .......................................................
307
DTC Logic ........................................................... ..307
Component Function Check ..................................308
Diagnosis Procedure .............................................309
P0441 EVAP CONTROL SYSTEM ..................312
DTC Logic ........................................................... ..312
Component Function Check ..................................313
Diagnosis Procedure .............................................314
P0443 EVAP CANISTER PURGE VOLUME
CONTROL SOLENOID VALVE .......................
317
DTC Logic ........................................................... ..317
Diagnosis Procedure .............................................318
Component Inspection (EVAP Canister Purge
Volume Control Solenoid Valve) ...........................
320
P0444, P0445 EVAP CANISTER PURGE
VOLUME CONTROL SOLENOID VALVE .......
322
DTC Logic ........................................................... ..322
Diagnosis Procedure .............................................322
Component Inspection (EVAP Canister Purge
Volume Control Solenoid Valve) ...........................
323
P0447 EVAP CANISTER VENT CONTROL
VALVE ..............................................................
325
DTC Logic ........................................................... ..325
Diagnosis Procedure .............................................325
Component Inspection (EVAP Canister Vent Con-
trol Valve) ............................................................ ..
327
P0448 EVAP CANISTER VENT CONTROL
VALVE ..............................................................
329
DTC Logic ........................................................... ..329
Diagnosis Procedure .............................................329
Component Inspection (EVAP Canister Vent Con-
trol Valve) ............................................................ ..
331
P0451 EVAP CONTROL SYSTEM PRES-
SURE SENSOR ...............................................
333
DTC Logic ............................................................ ..333
Diagnosis Procedure .............................................333
Component Inspection (EVAP Control System
Pressure Sensor) ................................................. ..
335
P0452 EVAP CONTROL SYSTEM PRES-
SURE SENSOR ...............................................
336
DTC Logic ..............................................................336
Diagnosis Procedure .............................................337
Component Inspection (EVAP Control System
Pressure Sensor) ................................................. ..
339
P0453 EVAP CONTROL SYSTEM PRES-
SURE SENSOR ...............................................
341
DTC Logic ..............................................................341
Diagnosis Procedure .............................................342
Component Inspection (EVAP Control System
Pressure Sensor) ................................................. ..
345
P0456 EVAP CONTROL SYSTEM .................346
DTC Logic ..............................................................346
Diagnosis Procedure .............................................347
Component Inspection (Fuel Filler Cap) ................350
P0460 FUEL LEVEL SENSOR .......................352
DTC Logic ............................................................ ..352
Diagnosis Procedure .............................................352
P0461 FUEL LEVEL SENSOR .......................353
DTC Logic ..............................................................353
Component Function Check ..................................353
Diagnosis Procedure .............................................354
P0462, P0463 FUEL LEVEL SENSOR ...........355
DTC Logic ..............................................................355
Diagnosis Procedure .............................................355
P0500 VSS ......................................................356
Description ........................................................... ..356
DTC Logic ..............................................................356
Component Function Check ..................................357
Diagnosis Procedure .............................................357
P0506 ISC SYSTEM ........................................358
Description .............................................................358
DTC Logic ..............................................................358
Diagnosis Procedure .............................................358
P0507 ISC SYSTEM ........................................360
Description .............................................................360
DTC Logic ..............................................................360
Diagnosis Procedure .............................................360
P050E COLD START CONTROL ...................362
Description .............................................................362
DTC Logic ..............................................................362
Diagnosis Procedure .............................................362
P0524 ENGINE OIL PRESSURE ....................364
Revision: 2010 May2011 QX56