2011 INFINITI QX56 sensor

BRC-40
< SYSTEM DESCRIPTION >[WITH VDC]
DIAGNOSIS SYSTEM [
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]
DIAGNOSIS SYSTEM [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]
CONSULT-III FunctionINFOID:0000000006222578
APPLICATION ITEMS
CONSULT-III can display each diagnostic item using the diagnostic test modes as follows.
*: The following diagnosis information is erased by erasing.
DTC
 Freeze frame data (FFD)
ECU IDENTIFICATION
ABS actuator and electric unit (cont rol unit) part number can be read.
SELF DIAGNOSTIC RESULT
Refer to BRC-51, "DTC Index".
When “CRNT” is displayed on self-diagnosis result,
 The system is presently malfunctioning.
When “PAST” is displayed on self-diagnosis result, System malfunction in the past is detect ed, but the system is presently normal.
Freeze frame data (FFD)
DATA MONITOR
×: Applicable
Mode Function description
ECU identification Parts number of ABS actuator and electric unit (control unit) can be read.
Self Diagnostic Result Self-diagnostic results and freeze frame data can be read and erased quickly.
*
DATA MONITOR Input/Output data in the ABS actuator and electric unit (control unit) can be read.
ACTIVE TEST Diagnostic Test Mode in
which CONSULT-III drives some act uators apart from the ABS actuator and
electric unit (control unit) and also shifts some parameters in a specified range.
WORK SUPPORT Components can be quickly and accurately adjusted.
Item name Display item
IGN counter
(0 − 39) The number of times that ignition switch is tu
rned ON after the DTC is detected is displayed.
 When “0” is displayed: It indicates that the system is presently malfunctioning.
 When except “0” is displayed: It indicates that system malfunction in the past is detected, but the system is pres- ently normal.
NOTE:
Each time when ignition switch is turned OFF to ON, numerical number increases in 1 → 2 → 3...38 → 39. When
the operation number of times exceeds 39, the number do not increase and “39” is displayed until self-diagnosis
is erased.
Item (Unit) Monitor item selection
Note
INPUT SIGNALS MAIN ITEMS
FR LH SENSOR
[km/h (MPH)] ××Wheel speed calculated by front LH wheel sensor is dis-
played.
FR RH SENSOR
[km/h (MPH)] ××Wheel speed calculated by front RH wheel sensor is dis-
played.
RR LH SENSOR
[km/h (MPH)] ××
Wheel speed calculated by rear LH wheel sensor is dis-
played.
RR RH SENSOR
[km/h (MPH)] ××Wheel speed calculated by rear RH wheel sensor is dis-
played.
DECEL G-SEN
(G) ××
Decel G detected by decel G sensor is displayed.
Revision: 2010 May2011 QX56

DIAGNOSIS SYSTEM [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]
BRC-41
< SYSTEM DESCRIPTION > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
FR RH IN SOL
(On/Off) ×Operation status of front
RH wheel ABS IN valve is dis-
played.
FR RH OUT SOL
(On/Off) ×Operation status of front
RH wheel ABS OUT valve is dis-
played.
FR LH IN SOL
(On/Off) ×
Operation status of front LH wheel ABS IN valve is dis-
played.
FR LH OUT SOL
(On/Off) ×Operation status of front LH wheel ABS OUT valve is dis-
played.
RR RH IN SOL
(On/Off) ×
Operation status of rear RH wh eel ABS IN valve is displayed
RR RH OUT SOL
(On/Off) ×
Operation status of rear RH wheel ABS OUT valve is dis-
played.
RR LH IN SOL
(On/Off) ×Operation status of rear LH
wheel ABS IN valve is dis-
played.
RR LH OUT SOL
(On/Off) ×Operation status of rear LH
wheel ABS OUT valve is dis-
played.
EBD WARN LAMP
(On/Off) Brake warning lamp ON/OFF status is displayed.
(Note 1)
STOP LAMP SW
(On/Off)××
Stop lamp switch signal input status is displayed.
MOTOR RELAY
(On/Off) ×
ABS motor and motor relay status is displayed.
ACTUATOR RLY
(On/Off) ×
ABS actuator relay status is displayed.
ABS WARN LAMP
(On/Off) ×
ABS warning lamp ON/OFF status is displayed.
(Note 1)
OFF LAMP
(On/Off) ×
VDC OFF indicator lamp ON/OFF status is displayed.(Note 1)
OFF SW
(On/Off) ××
VDC OFF switch signal input status is displayed.
SLIP/VDC LAMP
(On/Off) ×
VDC warning lamp ON/OFF status is displayed.
(Note 1)
BATTERY VOLT
(V) ××Voltage supplied to ABS actuator and electric unit (control
unit) is displayed.
GEAR ××Current gear position judged from current gear position sig-
nal is displayed.
ENGINE SPEED
(tr/min) ××
Engine speed status is displayed.
YAW RATE SEN
(d/s) ××
Yaw rate detected by yaw rate sensor is displayed.
R POSI SIG
(On/Off) R range signal input status judged from R range signal is
displayed.
4WD MODE MON
(Note 2)
(AUTO/LOCK/##) ××
4WD control status is displayed.
N POSI SIG
(On/Off) N range signal input status judged from N range signal is
displayed.
CV1
(On/Off) Cut valve 1 operation status is displayed.
CV2
(On/Off) Cut valve 2 operation status is displayed.
SV1
(On/Off) Suction valve 1 operation status is displayed.
Item (Unit)
Monitor item selection
Note
INPUT SIGNALS MAIN ITEMS
Revision: 2010 May2011 QX56

BRC-42
< SYSTEM DESCRIPTION >[WITH VDC]
DIAGNOSIS SYSTEM [
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]
Note 1: Refer to BRC-16, "System Description" for ON/OFF conditions of each warning lamp and indicator
lamp.
Note 2: Models with 4WD System
Note 3: Models with Advanced Driver Assistance System
Note 4: USS means “hill start assist”
ACTIVE TEST
The active test is used to determine and identify details of a malfunction, based on self-diagnosis test result
sand data obtained in the DATA MONITOR. In response to instructions from CONSULT-III, instead of those
SV2
(On/Off) Suction valve 2 operation status is displayed.
STOP LAMP SW2
(On/Off) Stop lamp switch signal input status is displayed.
ACCEL POS SIG
(%) ×
Displays the Accelerator pedal position
SIDE G-SENSOR
(m/s
2) ×
Side G detected by side G sensor is displayed.
STR ANGLE SIG
( ° ) ×
Steering angle detected by steering angle sensor is dis-
played.
PRESS SENSOR
(bar) ×Detects the brake fluid pressure of master cylinder part is
displayed.
ACCUM PRESS SEN
(bar) Detects the brake fluid pressure of accumulator is dis-
played.
CONT PRESS SEN
(Note 3)
(bar) Detects the brake fluid pressure of control pressure sensor
is displayed
EBD SIGNAL
(On/Off) EBD operation status is displayed.
ABS SIGNAL
(On/Off) ABS operation status is displayed.
TCS SIGNAL
(On/Off) TCS operation status is displayed.
VDC SIGNAL
(On/Off) VDC operation status is displayed.
EBD FAIL SIG
(On/Off) EBD fail-safe signal status is displayed.
ABS FAIL SIG
(On/Off) ABS fail-safe signal st
atus is displayed.
TCS FAIL SIG
(On/Off) TCS fail-safe signal status is displayed.
VDC FAIL SIG
(On/Off) VDC fail-safe signal status is displayed.
CRANKING SIG
(On/Off) Cranking status is displayed.
FLUID LEV SW
(On/Off) ×Brake fluid level signal input status via CAN communication
is displayed.
PARK BRAKE SW
(On/Off) ×Parking brake switch signal input status via CAN communi-
cation is displayed.
STP ON RLY
(On/Off) Stop lamp switch relay status is displayed.
USS SIG
(Note 4)
(On/Off) hill start assist operation status is displayed.
Item (Unit)
Monitor item selection
Note
INPUT SIGNALS MAIN ITEMS
Revision: 2010 May2011 QX56

BRC-44
< SYSTEM DESCRIPTION >[WITH VDC]
DIAGNOSIS SYSTEM [
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]
*: Immediately after being selected, status is “O n”. Status changes to “Off” after approx. 2 seconds.
Stop Lamp ON Relay
When “On” or “Off” is selected on display screen, t he following items are displayed when system is normal.
NOTE:
Display occasionally changes On/Off for a moment after ignition switch is turned ON. This is operation for
checking purposes and is not a malfunction.
WORK SUPPORT
Test item Display Item Display
On Off
STOP LAMP ON RELAY STOP LAMP ON RELAY On Off
Conditions Description
ST ANGLE SENSOR ADJUSTMENT Perform neutral position adjustment of steering angle sensor.
DECEL G SENSOR CALIBRATION Perform decel G sensor calibration.
Revision: 2010 May2011 QX56

ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)BRC-45
< ECU DIAGNOSIS INFORMATION > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
ECU DIAGNOSIS INFORMATION
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
Reference ValueINFOID:0000000006222579
CONSULT-III DATA MONITOR STANDARD VALUE
Monitor item Condition Reference values in normal operation
FR LH SENSOR Vehicle stopped 0.00 km/h (MPH)
When driving
(Note 1)Nearly matches the speedometer dis-
play (within
±10%)
FR RH SENSOR Vehicle stopped 0.00 km/h (MPH)
When driving
(Note 1)Nearly matches the speedometer dis-
play (within
±10%)
RR LH SENSOR Vehicle stopped 0.00 km/h (MPH)
When driving
(Note 1)Nearly matches the speedometer dis-
play (within
±10%)
RR RH SENSOR Vehicle stopped 0.00 km/h (MPH)
When driving
(Note 1)Nearly matches the speedometer dis-
play (within
±10%)
DECEL G-SEN When stopped Approx. 0 G
During acceleration Positive value
During deceleration Negative value
FR RH IN SOL Active On
Inactive Off
FR RH OUT SOL Active On
Inactive Off
FR LH IN SOL Active On
Inactive Off
FR LH OUT SOL Active On
Inactive Off
RR RH IN SOL Active On
Inactive Off
RR RH OUT SOL Active On
Inactive Off
RR LH IN SOL Active On
Inactive Off
RR LH OUT SOL Active On
Inactive Off
EBD WARN LAMP When brake warning lamp is ON
(Note 2)On
When brake warning lamp is OFF
(Note 2)Off
STOP LAMP SW Brake pedal depressed On
Brake pedal not depressed Off
MOTOR RELAY Active On
Inactive Off
ACTUATOR RLY Active On
Inactive (in fail-safe mode) Off
Revision: 2010 May2011 QX56

BRC-46
< ECU DIAGNOSIS INFORMATION >[WITH VDC]
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
ABS WARN LAMPWhen ABS warning lamp is ON
(Note 2)On
When ABS warning lamp is OFF
(Note 2)Off
OFF LAMP When VDC OFF indicator lamp is ON
(Note 2)On
When VDC OFF indicator lamp is OFF
(Note 2)Off
OFF SW VDC OFF switch ON On
VDC OFF switch OFF Off
SLIP/VDC LAMP When VDC warning lamp is ON or Blinking
(Note 2)On
When VDC warning lamp is OFF
(Note 2)Off
BATTERY VOLT Ignition switch ON 10 – 16 V
GEAR Driving 1 – 7
Depending on shift status
ENGINE SPEED Engine stopped 0 tr/min
Engine running Almost same reading as tachometer
YAW RATE SEN Vehicle stopped Approx. 0 d/s
Turning right Negative value
Turning left Positive value
R POSI SIG When selector lever is in the R position On
When selector lever is in the other position than R Off
4WD MODE MON
(Note 3)
When 4WD sift switch is AUTO position AUTO
When 4WD sift switch is 4H position LOCK
When 4WD sift switch is 4L position ##
N POSI SIG When selector lever is in the N position On
When selector lever is in the other position than N Off
CV1 Active On
Inactive Off
CV2 Active On
Inactive Off
SV1 Active On
Inactive Off
SV2 Active On
Inactive Off
STOP LAMP SW2 Brake pedal depressed On
Brake pedal not depressed Off
ACCEL POS SIG Never depress accelerator pedal
(with ignition switch ON)
0%
Depress accelerator pedal
(with ignition switch ON) 0 – 100%
SIDE G-SENSOR Vehicle stopped
Approx. 0 m/s
2
Right turn Negative value
Left turn Positive value
STR ANGLE SIG When driving straight 0
±2.5 °
When steering wheel is steered to LH by 90 °Approx. +90 °
When steering wheel is steered to RH by 90 °Approx. –90 °
Monitor item Condition Reference values in normal operation
Revision: 2010 May2011 QX56

ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)BRC-47
< ECU DIAGNOSIS INFORMATION > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
Note 1: Confirm tire pressure is standard value.
Note 2: Refer to BRC-16, "
System Description" for ON/Blinking/OFF conditions of each warning lamp and indi-
cator lamp.
Note 3: Models with 4WD System
Note 4: Models with Advanced Driver Assistance System
Note 5: USS means “hill start assist”.
Fail-safeINFOID:0000000006222580
VDC FUNCTION, TCS FUNCTION, hill start assi st FUNCTION AND BRAKE LIMITED SLIP DIFFER-
ENTIAL (BLSD) FUNCTION
VDC warning lamp in combination meter turn ON w hen a malfunction occurs in system [ABS actuator and
electric unit (control unit)]. The control is suspended for VDC function, TCS function, hill start assist function
and brake limited slip differential (BLSD) function. T he Vehicle status becomes the same as models without
PRESS SENSORBrake pedal not depressed Approx. 0 bar
Brake pedal depressed (
−40) – (+300) bar
ACCUM PRESS SEN With ig nition switch ON Approx. 0 – 210 bar (Proportional to the
amount of accumulated pressure in the
accumulator)
CONT PRESS SEN
(Note 4)Brake pedal not depressed Approx. 0 bar
Brake pedal depressed ( −40) – (+300) bar
EBD SIGNAL EBD is active On
EBD is inactive Off
ABS SIGNAL ABS is active On
ABS is inactive Off
TCS SIGNAL TCS is active On
TCS is inactive Off
VDC SIGNAL VDC is active On
VDC is inactive Off
EBD FAIL SIG In EBD fail-safe On
EBD is normal Off
ABS FAIL SIG In ABS fail-safe On
ABS is normal Off
TCS FAIL SIG In TCS fail-safe On
TCS is normal Off
VDC FAIL SIG In VDC fail-safe On
VDC is normal Off
CRANKING SIG At cranking On
Other than at cranking Off
FLUID LEV SW When brake fluid level switch is ON (brake fluid level
is less than the specified level)
On
When brake fluid level switch is OFF Off
PARK BRAKE SW When parking brake is active On
Parking brake is released Off
STP ON RLY Stop lamp relay is active On
Stop lamp relay is inactive Off
USS SIG
(Note 5)hill start assist is active On
hill start assist is inactive Off
Monitor item Condition Reference values in normal operation
Revision: 2010 May2011 QX56

BRC-48
< ECU DIAGNOSIS INFORMATION >[WITH VDC]
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
VDC function, TCS function, hill start assist function and
brake limited slip differential (BLSD) function. How-
ever, ABS function and EBD function are operated normally.
ABS FUNCTION
ABS warning lamp and VDC warning lamp in combinati on meter turn ON when a malfunction occurs in system
[ABS actuator and electric unit (control unit)]. The c ontrol is suspended for VDC function, TCS function, ABS
function, hill start assist function and brake limited sl ip differential (BLSD) function. The vehicle status
becomes the same as models without VDC function, TCS f unction, ABS function, hill start assist function and
brake limited slip differential (BLSD) function. However, EBD function is operated normally.
NOTE:
ABS self-diagnosis sound may be heard the same as in the normal condition, because self-diagnosis is per-
formed when ignition switch turns ON and when vehicle initially starts.
EBD FUNCTION
ABS warning lamp, brake warning lamp and VDC warning lamp in combination meter turn ON when a mal-
function occurs in system [ABS actuator and electric unit (control unit)]. The control is suspended for VDC
function, TCS function, ABS function, EBD function, hill start assist function and brake limited slip differential
(BLSD) function. The vehicle status becomes the sa me as models without VDC function, TCS function, ABS
function, EBD function, hill star t assist function and brake limited slip differential (BLSD) function.
DTC Malfunction detected condition Fail-safe condition
C1101 When an open circuit is detected in rear RH wheel sensor circuit.
The following functions are sus-
pended.
 VDC function
 TCS function
 ABS function
 EBD function (only when both 2 rear wheels are malfunctioning)
 hill start assist function
 Brake limited slip differential (BLSD) function
C1102 When an open circuit is detected in rear LH wheel sensor circuit.
C1103 When an open circuit is detected in front RH wheel sensor circuit.
C1104 When an open circuit is detected in front LH wheel sensor circuit.
C1105
 When power supply voltage of rear RH wheel sensor is low.
 When distance between rear RH wheel sensor and rear RH wheel sensor rotor is
large.
 When installation of rear RH wheel sensor or rear RH wheel sensor rotor is not normal.
C1106  When power supply voltage of rear LH wheel sensor is low.
 When distance between rear LH wheel sensor and rear LH wheel sensor rotor is
large.
 When installation of rear LH wheel sensor or rear LH wheel sensor rotor is not nor-
mal.
C1107  When power supply voltage of front RH wheel sensor is low.
 When distance between front RH wheel sensor and front RH wheel sensor rotor
is large.
 When installation of front RH wheel sensor or front RH wheel sensor rotor is not normal.
C1108  When power supply voltage of front LH wheel sensor is low.
 When distance between front LH wheel sensor and front LH wheel sensor rotor is
large.
 When installation of front LH wheel sensor or front LH wheel sensor rotor is not normal.
C1109  When ignition voltage is 10 V or less.
 When ignition voltage is 16 V or more. The following functions are sus-
pended.
 VDC function
 TCS function
 ABS function
 EBD function
 hill start assist function
 Brake limited slip differential
(BLSD) function
C 1111
 When a malfunction is detected in motor or motor relay.
 When a low pressure malfunction is detected in accumulator.
 When a malfunction is detected in accumulator pressure sensor.
Revision: 2010 May2011 QX56