2011 INFINITI QX56 Wiring

TM-86
< WIRING DIAGRAM >[7AT: RE7R01B]
A/T SHIFT LOCK SYSTEM
JCDWM1067GB
Revision: 2010 May2011 QX56

A/T SHIFT LOCK SYSTEMTM-87
< WIRING DIAGRAM > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
JCDWM1068GB
Revision: 2010 May2011 QX56

U1000 CAN COMM CIRCUITTM-103
< DTC/CIRCUIT DIAGNOSIS > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
U1000 CAN COMM CIRCUIT
DescriptionINFOID:0000000006226798
CAN (Controller Area Network) is a serial communication line for real-time application. It is an on-vehicle mul-
tiplex communication line with high data communica tion speed and excellent malfunction detection ability.
Many electronic control units are equipped onto a vehicl e, and each control unit shares information and links
with other control units during operation (not independently ). In CAN communication, control units are con-
nected with 2 communication lines (CAN-H line, CAN-L li ne) allowing a high rate of information transmission
with less wiring. Each control unit transmits/recei ves data but selectively reads required data only.
DTC LogicINFOID:0000000006226799
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” is previously c onducted, always turn ignition switch OFF and wait at
least 10 seconds before performing the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
With CONSULT-III
1. Start the engine.
2. Run engine for at least 2 cons ecutive seconds at idle speed.
3. Perform “Self Diagnostic Resu lts” in “TRANSMISSION”.
With GST
Follow the procedure “With CONSULT-III”
Is
“U1000” detected?
YES >> Go to TM-103, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006226800
Go to LAN-18, "Trouble Diagnosis Flow Chart".
DTC Trouble diagnosis name DTC is detected if... Possible cause
U1000 CAN Communication Line TCM is not transmitting or re-
ceiving CAN communication
signal for 2 seconds or more. Harness or connectors
(CAN communication line is
open or shorted.)
TCM
Revision: 2010 May2011 QX56

TM-104
< DTC/CIRCUIT DIAGNOSIS >[7AT: RE7R01B]
P0615 STARTER RELAY
P0615 STARTER RELAY
DescriptionINFOID:0000000006226801
TCM prohibits cranking other than at “P” or “N” position.
DTC LogicINFOID:0000000006226802
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” is previously c onducted, always turn ignition switch OFF and wait at
least 10 seconds before performing the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
With CONSULT-III
1. Shift the selector lever to “P” and “N” positions.
2. Turn ignition switch ON and wait 2 seconds or more.
3. Perform “Self Diagnostic Results” in “TRANSMISSION”.
Is
“P0615” detected?
YES >> Go to TM-104, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006226803
1.CHECK STARTER RELAY SIGNAL
1. Turn ignition switch ON.
2. Check voltage between IPDM E/R connector terminal and ground.
Is the inspection result normal?
YES >> Check starter relay circuit. Refer to STR-7, "Wiring Diagram".
NO >> GO TO 2.
2. CHECK HARNESS BETWEEN A/T ASSEMBLY AND IPDM E/R (PART 1)
1. Turn ignition switch OFF.
2. Disconnect A/T assembly c onnector and IPDM E/R connector.
3. Check the continuity between A/T assembly vehi cle side harness connector terminal and IPDM E/R vehi-
cle side harness connector terminal.
DTC Trouble diagnosis name DTC is detected if... Possible cause
P0615 Starter Relay Circuit The starter monitor value is
OFF when the ignition switch is
ON at the “P” and “N” positions. Harness or connectors
(Starter relay and TCM circuit
is open or shorted.)
 Starter relay circuit
IPDM E/R connector
GroundCondition Voltage (Approx.)
Connector Terminal
E15 48 Selector lever in “P” and
“N” positions.
Battery voltage
Selector lever in other
positions. 0 V
Revision: 2010 May2011 QX56

TM-152
< DTC/CIRCUIT DIAGNOSIS >[7AT: RE7R01B]
MAIN POWER SUPPLY AND GROUND CIRCUIT
YES >> GO TO 5.
NO >> Repair or replace damaged parts.
5.CHECK INTERMITTENT INCIDENT
Refer to GI-40, "
Intermittent Incident".
Is the inspection result normal?
YES >> Replace the control valve & TCM. Refer to TM-182, "Exploded View".
NO >> Repair or replace damaged parts.
6.DETECT MALFUNCTIONING ITEM (PART 1)
Check the following.
 Harness for short or open between battery positive term inal and A/T assembly vehicle side harness connec-
tor terminal 2. Refer to PG-11, "
Wiring Diagram - BATTERY POWER SUPPLY -".
Battery
 10A fuse (No.38, located in the fuse, fusible link and relay box). Refer to PG-141, "
Fuse and Fusible Link
Arrangement".
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-40, "Intermittent Incident".
NO >> Repair or replace damaged parts.
7.CHECK HARNESS BETWEEN IPDM E/ R AND A/T ASSEMBLY (PART 1)
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R vehicle side harness connector terminal and A/T assembly vehicle
side harness connector terminals.
Is the inspection result normal?
YES >> GO TO 8.
NO >> Repair or replace damaged parts.
8.CHECK HARNESS BETWEEN IPDM E/ R AND A/T ASSEMBLY (PART 2)
Check continuity between A/T assembly vehicle side harness connector terminal and ground.
Is the inspection result normal?
YES >> GO TO 9.
NO >> Repair or replace damaged parts.
9.DETECT MALFUNCTIONING ITEM (PART 2)
Check the following.
 Harness for short or open between ignition switch and IPDM E/R. Refer to PG-89, "
Wiring Diagram - IGNI-
TION POWER SUPPLY -".
 Ignition switch
 10A fuse (No.55, located in the IPDM E/R). Refer to PG-143, "
Fuse, Connector and Terminal Arrangement".
 IPDM E/R
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-40, "Intermittent Incident".
NO >> Repair or replace damaged parts.
IPDM E/R vehicle side harness connector A/T assembly vehicle side harness connector Continuity
Connector Terminal Connector Terminal
E15 57 F51 1
Existed
6
A/T assembly vehicle side harness connector
GroundContinuity
Connector Terminal
F51 1
Not existed
6
Revision: 2010 May2011 QX56

SHIFT LOCK SYSTEMTM-157
< DTC/CIRCUIT DIAGNOSIS > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
SHIFT LOCK SYSTEM
Component Function CheckINFOID:0000000006226882
1.CHECK A/T SHIFT LOCK OPERATION (PART 1)
1. Turn ignition switch ON.
2. Shift the selector lever to “P” position.
3. Attempt to shift the selector lever to any other position with the brake pedal released.
Can the selector lever be shifted to any other position?
YES >> Go to TM-157, "Diagnosis Procedure".
NO >> GO TO 2.
2.CHECK A/T SHIFT LOCK OPERATION (PART 2)
Attempt to shift the selector lever to any other position with the brake pedal depressed.
Can the selector lever be shifted to any other position?
YES >> INSPECTION END
NO >> Go to TM-157, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000006226883
1. CHECK POWER SOURCE
1. Turn ignition switch OFF.
2. Disconnect fuse block (J/B) connector.
3. Turn ignition switch ON.
4. Check voltage between fuse block (J/B) connector terminal and ground.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Check the following.  10A fuse [No. 3, located in fuse block (J/B)]. Refer to PG-140, "
Fuse, Connector and Terminal
Arrangement".
 Harness for short or open between ignition switch and fuse block (J/B). Refer to PG-89, "
Wiring
Diagram - IGNITION POWER SUPPLY -".
 Ignition switch
2.CHECK HARNESS BETWEEN FUSE BLOCK (J/B ) AND STOP LAMP SWITCH (PART 1)
1. Turn ignition switch OFF.
2. Disconnect stop lamp switch connector.
3. Check continuity between fuse block (J/B) vehicl e side harness connector terminal and stop lamp switch
vehicle side harness connector terminal.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace damaged parts.
3.CHECK HARNESS BETWEEN FUSE BLOCK (J/B ) AND STOP LAMP SWITCH (PART 2)
Check continuity between stop lamp switch vehicle side harness connector terminal and ground.
Fuse block (J/B) connector
GroundVoltage (Approx.)
Connector Terminal
E103 4F Battery voltage
Fuse block (J/B) vehicle side harness connector Stop lamp switch vehicle side harness connector Continuity
Connector Terminal Connector Terminal
E103 4F E115 3 Existed
Revision: 2010 May2011 QX56

SELECTOR LEVER POSITION INDICATORTM-163
< DTC/CIRCUIT DIAGNOSIS > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
YES >> Check intermittent incident. Refer to GI-40, "Intermittent Incident".
NO >> Repair or replace damaged parts.
9.CHECK POWER SOURCE (PART 2)
1. Turn ignition switch OFF.
2. Disconnect A/T shift selector connector.
3. Turn ignition switch ON.
4. Check voltage between A/T shift selector vehicle side harness connector terminals.
Is the inspection result normal?
YES >> GO TO 10.
NO >> Check illumination circuit. Refer to INL-34, "
Wiring Diagram".
10.CHECK SHIFT POSITION SWITCH (PART 2)
1. Disconnect shift position switch connector.
2. Check continuity between A/T shift selector connec tor terminals and shift position switch connector termi-
nals.
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace damaged parts.
Component Inspection (Selecto r Lever Position Indicator)INFOID:0000000006226889
1.CHECK SELECTOR LEVER POSITION INDICATOR
Check that selector lever position indicator lamps turn on.
CAUTION:
Connect the fuse between the termina ls when applying the voltage.
A/T shift selector vehicle side harness connector
Condition Voltage (Approx.)
Connector Te r m i n a l
+ −
M57 9 10 Lighting switch 1ST Battery voltage
A/T shift selector connector Shift position switch connector Continuity
Connector Terminal Connector Terminal
M57 9
M281 9Existed
1, 2, 3, 4, 5, 8, 10, 12 Not existed
10 8Existed
1, 2, 3, 4, 5, 9, 10, 12 Not existed
Shift position switch harness connector Condition Status
Te r m i n a l
+ (fuse) −
110 Apply 12 V direct current between
terminals 1 and 10.
“M” mode indicato
r lamp turns on.
2
12Apply 12 V direct current between
terminals 2 and 12.
“P” position indicator lamp turns on.
3 Apply 12 V direct current between
terminals 3 and 12. “R” position indica
tor lamp turns on.
4 Apply 12 V direct current between
terminals 4 and 12.
“D” position indica
tor lamp turns on.
5 Apply 12 V direct current between
terminals 5 and 12. “N” position indica
tor lamp turns on.
98 Apply 12 V direct current between
terminals 9 and 8. Illumination lamp turns on.
Revision: 2010 May2011 QX56

PRECAUTIONSVTL-3
< PRECAUTION >
C
DE
F
G H
J
K L
M A
B
VTL
N
O P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000006376373
The Supplemental Restraint System such as “A IR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severi ty of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
• To avoid rendering the SRS inoper ative, which could increase the risk of personal injury or death in
the event of a collision that would result in air ba g inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
 Improper maintenance, including in correct removal and installation of the SRS, can lead to personal
injury caused by unintentional act ivation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIR BAG”.
 Do not use electrical test equipm ent on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identi fied by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
 When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s)
with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly
causing serious injury.
 When using air or electric power tools or hammers , always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution Necessary for Steering Wh eel Rotation after Battery Disconnect
INFOID:0000000006376453
NOTE:
 Before removing and installing any control units, first tu rn the push-button ignition switch to the LOCK posi-
tion, then disconnect both battery cables.
 After finishing work, confirm that all control unit connectors are connected properly, then re-connect both
battery cables.
 Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.
If a DTC is detected, perform trouble diagnos is according to self-diagnosis results.
For vehicle with steering lock unit, if the battery is disconnected or discharged, the steering wheel will lock and
cannot be turned.
If turning the steering wheel is required with the batte ry disconnected or discharged, follow the operation pro-
cedure below before starting the repair operation.
OPERATION PROCEDURE
1. Connect both battery cables. NOTE:
Supply power using jumper cables if battery is discharged.
2. Turn the push-button ignition switch to ACC position. (At this time, the steering lock will be released.)
3. Disconnect both battery cables. The steering lock wil l remain released with both battery cables discon-
nected and the steering wheel can be turned.
4. Perform the necessary repair operation.
Revision: 2010 May2011 QX56